LEMON Manuals: Even more car manuals for everyone
Home >> GMC >> 2021 >> Yukon AT4 >> Repair and Diagnosis >> Steering >> Steering Column >> Steering Wheel And Column >> Repair Instructions >> Steering Column Replacement (N37) >> Installation Procedure

Installation Procedure

  1. GM5549533Courtesy of GENERAL MOTORS COMPANY

    Column Lock Module (1) - Install

  2. GM5549529Courtesy of GENERAL MOTORS COMPANY
    CAUTION:

    Refer to Fastener Caution .

    Steering Column Lock Control Module Bolt (1) - Install and tighten [ 4x ] - Fastener Specifications 

  3. GM5519913Courtesy of GENERAL MOTORS COMPANY

    Steering Column (1) - Install

  4. Connect the electrical connectors attached to the steering column (1).
  5. GM5519911Courtesy of GENERAL MOTORS COMPANY

    Steering Column Nut (1) - Install and tighten [ 4x ] - Fastener Specifications 

  6. GM5519908Courtesy of GENERAL MOTORS COMPANY

    Upper Intermediate Steering Shaft (1) - Install

  7. GM5519907Courtesy of GENERAL MOTORS COMPANY

    Upper Intermediate Steering Shaft Bolt (1) - Install and tighten - Fastener Specifications 

  8. GM5519906Courtesy of GENERAL MOTORS COMPANY
    WARNING:

    Upon installing the floor duct to the side of the HVAC case, it is necessary to verify duct opening is completely installed, surrounding the HVAC case outlet port. Failure to do so could result in the duct falling downward, with the potential to interfere with driver's legs and gas/brake pedal operation.

    Floor Front Air Outlet Duct - Left Side (1) - Install

  9. GM5519904Courtesy of GENERAL MOTORS COMPANY

    Floor Front Air Outlet Duct Bolt (1) - Install and tighten - Fastener Specifications

  10. GM5520387Courtesy of GENERAL MOTORS COMPANY

    Instrument Panel Lower Trim Panel Insulator (1) - Install

  11. GM5520386Courtesy of GENERAL MOTORS COMPANY

    Instrument Panel Lower Insulator Retainer (1) - Install [ 2x ]

  12. GM5519901Courtesy of GENERAL MOTORS COMPANY

    Connect the electrical connector.

  13. Install turn signal switch and turn signal switch bracket (1) as an assembly.
  14. GM5537037Courtesy of GENERAL MOTORS COMPANY

    Ensure the locking tab on the right side of the turn signal switch bracket is fully seated.

  15. GM5537035Courtesy of GENERAL MOTORS COMPANY

    Ensure the locking tab on the left side of the turn signal switch bracket is fully seated.

  16. GM5536895Courtesy of GENERAL MOTORS COMPANY

    Wiring Harness - Move into position

  17. Install the wiring harness clip (1) on the left side of the turn signal bracket.
  18. GM5519898Courtesy of GENERAL MOTORS COMPANY

    Ensure the steering wheel airbag coil is CENTERED during installation. Steering Wheel Airbag Coil Centering

  19. Steering Wheel Airbag Coil (1) - Install
  20. Connect the electrical connectors.
  21. GM5519891Courtesy of GENERAL MOTORS COMPANY

    Instrument Panel Steering Column Lower Trim Cover (2) - Install

  22. Instrument Panel Steering Column Lower Trim Cover Bolt (1) - Install and tighten [ 3x ] - Fastener Specifications
  23. GM5527242Courtesy of GENERAL MOTORS COMPANY

    Clip the instrument panel steering column opening closeout (2) to the instrument panel steering column upper trim cover (1).

  24. GM5519890Courtesy of GENERAL MOTORS COMPANY

    Secure the instrument panel steering column upper trim cover (1) to the instrument panel steering column lower trim cover.

  25. GM5519895Courtesy of GENERAL MOTORS COMPANY

    Steering Wheel (2) - Install

  26. If a NEW threaded component is being installed, loosen the adhesive using a metal pick or similar tool before proceeding. If threaded component is reused, prepare the threaded component using the following steps:
    1. Remove any loose cured adhesive from the external threads of the component using a lint free cloth.
    2. Thread the cleaned component into the internal mating threads and remove to loosen trapped cured adhesive.
    3. Apply thread locking adhesive to the external threads of the component. Adhesives, Fluids, Lubricants, and Sealers 
    4. Ensure there are no gaps in the thread locking adhesive once applied to the component.
  27. Steering Wheel Bolt (1) - Install and tighten - Fastener Specifications 
  28. GM5519893Courtesy of GENERAL MOTORS COMPANY

    Connect the electrical connectors.

  29. Install any connector position assurance (CPA) devices or secondary locks.
  30. Steering Wheel Airbag (2) - Install
  31. Steering Wheel Airbag Bolt (1) - Install and tighten - Fastener Specifications
  32. GM5519892Courtesy of GENERAL MOTORS COMPANY

    Install the 2 steering wheel airbag access hole covers (1).

  33. GM5517090Courtesy of GENERAL MOTORS COMPANY

    Instrument Panel Knee Bolster (1) - Install

  34. GM5517088Courtesy of GENERAL MOTORS COMPANY

    Instrument Panel Knee Bolster Bolt (2) - Install and tighten [ 2x ] - Fastener Specifications

  35. Hood Primary Latch Release Cable Handle (1) - Install
  36. GM5517140Courtesy of GENERAL MOTORS COMPANY

    Connect the electrical connectors.

  37. Instrument Panel Switch Trim Plate (2) - Install
  38. Instrument Panel Switch Trim Plate Bolt (1) - Install and tighten - Fastener Specifications
  39. GM5517141Courtesy of GENERAL MOTORS COMPANY

    Connect the electrical connectors.

  40. Instrument Panel Trim Pad (2) - Install
  41. Instrument Panel Trim Pad Bolt (1) - Install and tighten [ 2x ] - Fastener Specifications
  42. GM5517142Courtesy of GENERAL MOTORS COMPANY

    Instrument Panel Trim Plate Applique (1) - Install

  43. GM5517144Courtesy of GENERAL MOTORS COMPANY

    Instrument Panel Fuse Block Access Hole Cover (1) - Install

  44. GM5515686Courtesy of GENERAL MOTORS COMPANY

    Instrument Panel Lower Trim Panel Outer Filler (1) - Install

  45. Enable the SIR System. SIR Disabling and Enabling
  46. Remove the device used to prevent steering column rotation.