Steering Gear Replacement (2.4L)
Courtesy of GENERAL MOTORS COMPANY Steering Gear Replacement (2.4L)
| Callout |
Component Name |
CAUTION:
Electrostatic discharge (ESD) can damage many solid-state electrical components. ESD susceptible components may or may not be labeled with the ESD symbol. Handle all electrical components carefully. Use the following precautions in order to avoid ESD damage:
- Touch a metal ground point in order to remove your body's static charge before servicing any electronic component; especially after sliding across the vehicle seat.
- Do not touch exposed terminals. Terminals may connect to circuits susceptible the ESD damage.
- Do not allow tools to contact exposed terminals when servicing connectors.
- Do not remove components from their protective packaging until required to do so.
- Avoid the following actions unless required by the diagnostic procedure:
- Jumpering or grounding of the components or connectors.
- Connecting test equipment probes to components or connectors. Connect the ground lead first when using test probes.
- Ground the protective packaging of any component before opening. Do not rest solid-state components on metal workbenches or on top of TVs, radios or other electrical devices.
CAUTION:
With wheels of the vehicle facing straight ahead, secure the steering wheel utilizing steering column anti-rotation pin, steering column lock or a strap to prevent rotation. Locking of the steering column will prevent damage and a possible malfunction of the SIR system. The steering wheel must be secured in position before disconnecting the following components:
- The steering column
- The intermediate shaft(s)
- The steering gear
After disconnecting these components, do not rotate the steering wheel or move the front tires and wheels. Failure to follow this procedure may cause the SIR coil assembly to become un-centered and cause possible damage to the SIR coil. If you think the SIR coil has become un-centered, refer to your specific SIR coil's centering procedure to re-center SIR Coil.
Preliminary Procedure
- With the front wheels in the straight ahead position, turn the ignition switch to the OFF position and remove the key from the ignition lock cylinder. Rotate the steering wheel in order to LOCK the steering column.
- If you will be transferring the old power steering assist motor to a new steering gear, prepare the power steering control module for removal. Refer to Power Steering Control Module Programming and Setup
.
- Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle
.
- Disconnect the outer tie rod ends from the steering knuckles. Refer to Steering Linkage Outer Tie Rod Replacement .
- Remove the catalytic converter. Refer to Catalytic Converter Replacement (LEA)
.
- Remove the propeller shaft, if equipped. Refer to Propeller Shaft Replacement
.
- Remove the transmission rear mount from the transmission rear mount bracket. Refer to Transmission Rear Mount Replacement (AWD)
, Transmission Rear Mount Replacement (FWD)
, if equipped with MH7 or MHC. Refer to Transmission Rear Mount Replacement
if equipped with MH2 or MH4.
- Disconnect the intermediate steering shaft from the steering gear. Refer to Intermediate Steering Shaft Replacement
.
- Partially lower the rear of the drivetrain and front suspension frame in order to gain clearance for the steering gear. Refer to Drivetrain and Front Suspension Frame Replacement
.
|
| 1 |
Steering Gear Bolt (Qty: 2)
Procedure
- Remove the 2 steering gear bolts.
Discard the bolts.
- Install 2 NEW steering gear bolts.
Tighten 110 N.m (81 lb ft) |
| 2 |
Steering Gear Procedure
- Remove the steering gear heat shield. Refer to Steering Gear Heat Shield Replacement (2.4L) .
- Disconnect the electrical connectors. Refer to FEP Connectors (Steering Gear)
.
- Carefully remove the steering gear through the right front wheel opening.
- Transfer parts if necessary. Refer to Power Steering Assist Motor Replacement if necessary.
- After the installation is complete, measure and adjust the front toe. Refer to Wheel Alignment - Steering Wheel Angle and/or Front Toe Adjustment
.
- If you transferred the old power steering assist motor from the old steering gear to the new steering gear, proceed with the scan tool instructions for preparing the power steering control module for removal. Refer to Power Steering Control Module Programming and Setup
.
If you installed a new steering gear with a new power steering assist motor, program the power steering control module. Refer to Power Steering Control Module Programming and Setup
.
TIP:
The power steering control module is part of the power steering assist motor. |