LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2024 >> Edge Titanium >> Repair and Diagnosis >> Electrical >> Gauges >> Instrument Panel And Console >> Removal And Installation >> Instrument Panel Upper Section >> Removal

Instrument Panel Upper Section: Removal

NOTE: Removal steps in this procedure may contain installation details.
  1. Remove the instrument panel. Refer to: Instrument Panel .
  2. Remove the instrument panel speaker grille. Use the General Equipment: Interior Trim Remover
    GFD815427Courtesy of FORD MOTOR COMPANY
  3. Remove the bolts and the instrument panel speaker.

    • Disconnect the electrical connector.

      Torque

      : 2.5 Nm

    GFD815428Courtesy of FORD MOTOR COMPANY
    GFD815429Courtesy of FORD MOTOR COMPANY
    GFD815430Courtesy of FORD MOTOR COMPANY
  4. Remove the bolts and the information and entertainment display unit.

    • Disconnect the electrical connectors.

      Torque

      : 2.5 Nm

    GFD815431Courtesy of FORD MOTOR COMPANY
  5. Remove the screws and position the APIM down and rearward.

    Torque

    : 2.5 Nm

    GFD814828Courtesy of FORD MOTOR COMPANY
  6. Disconnect the electrical connectors.
    GFD814838Courtesy of FORD MOTOR COMPANY
  7. Remove the bolts and the ACM.

    • Disconnect the electrical connectors.

      Torque

      : 2.5 Nm

    GFD815432Courtesy of FORD MOTOR COMPANY
  8. Release the clips and remove the upper instrument panel storage bin.

    Torque

    : 2.5 Nm

    GFD815433Courtesy of FORD MOTOR COMPANY
  9. Remove bolts, release the clips and remove the IPC bezel.

    Torque

    : 2.5 Nm

    GFD814672Courtesy of FORD MOTOR COMPANY
  10. Remove the bolts and the IPC.

    Torque

    : 2.5 Nm

    GFD815434Courtesy of FORD MOTOR COMPANY
  11. Disconnect the electrical connector.
    GFD814674Courtesy of FORD MOTOR COMPANY
  12. Remove the headlamp switch.

    • Disconnect the electrical connector.

    GFD815435Courtesy of FORD MOTOR COMPANY
    • Disconnect the electrical connector.

    • Remove the bolts.

      Torque

      : 8 Nm

    • Through the opening, push the tabs down and detach the clips.

    GFD815436Courtesy of FORD MOTOR COMPANY
  13. Pivot the driver knee airbag down, separate the knee bolster clips and remove the driver knee airbag.
    GFD815437Courtesy of FORD MOTOR COMPANY
  14. Release the clips and remove the glove compartment finish panel.
    GFD815438Courtesy of FORD MOTOR COMPANY
  15. Open the glove compartment.
    GFD814594Courtesy of FORD MOTOR COMPANY
  16. Detach the glove compartment damper.
    GFD814595Courtesy of FORD MOTOR COMPANY
  17. Release the tabs and fully lower the glove compartment.
    GFD814596Courtesy of FORD MOTOR COMPANY
    1. Disconnect the electrical connectors.
    2. Remove the bolts.

      Torque

      : 4 Nm

    3. Remove the screws.

      Torque

      : 2.5 Nm

    4. Release the clips and remove the glove compartment. Use the General Equipment: Interior Trim Remover
    GFD815439Courtesy of FORD MOTOR COMPANY
  18. Remove the screws and the lower steering column shroud.

    Torque

    : 2.5 Nm

    GFD815440Courtesy of FORD MOTOR COMPANY
  19. Disconnect the electrical connectors.
    GFD815441Courtesy of FORD MOTOR COMPANY
  20. NOTE: Vehicles with power adjustable steering column.

    Detach the retainer, disconnect the power tilt motor and power telescopic motor electrical connectors.

    GFD811443Courtesy of FORD MOTOR COMPANY
  21. Disconnect the deployable column electrical connector.
    GFD815442Courtesy of FORD MOTOR COMPANY
  22. NOTE: Do not reuse steering column bolts. This may result in fastener failure and steering column detachment or loss of steering control. Failure to follow this instruction may result in serious injury to vehicle occupant(s).

    Remove and discard the bolts and remove the steering column.

    Torque

    : 25 Nm

    GFD815443Courtesy of FORD MOTOR COMPANY
  23. Remove the engine start stop button.

    • Disconnect the electrical connector.

    GFD815444Courtesy of FORD MOTOR COMPANY
  24. Remove the 2 screws, release the clips and remove the lower instrument panel trim panel.
    GFD815445Courtesy of FORD MOTOR COMPANY
  25. Remove passenger airbag to cross car beam bolts.

    • Disconnect the electrical connector.

      Torque

      : 9 Nm

    GFD815446Courtesy of FORD MOTOR COMPANY
  26. Remove the HVAC to instrument panel upper section bolts.

    • Detach the wiring harness from the instrument panel upper section and position aside.

      Torque

      : 4 Nm

    GFD815447Courtesy of FORD MOTOR COMPANY
  27. NOTE: Make sure that all electrical connectors and wiring are not hindered before removing the instrument panel upper section or damage to the components may occur.

    Remove the instrument panel upper section to in-vehicle cross beam bolts and remove the instrument panel upper section.

    Torque

    : 2.5 Nm

GFD815448Courtesy of FORD MOTOR COMPANY