LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2011 >> Taurus Limited, AWD >> Repair and Diagnosis >> Engine Performance >> Fuel Delivery >> Fuel System - General Information >> General Procedures >> Fuel Tank Draining - L-Shaped

Fuel Tank Draining - L-Shaped

SPECIAL TOOL(S)

G07810614
Fuel Storage Tanker
164-R3202 or equivalent
G07810615
Wrench, Fuel Tank Sender Unit
310-123
WARNING: Do not smoke, carry lighted tobacco or have an open flame of any type when working on or near any fuel-related component. Highly flammable mixtures are always present and may be ignited. Failure to follow these instructions may result in serious personal injury.
WARNING: Do not carry personal electronic devices such as cell phones, pagers or audio equipment of any type when working on or near any fuel-related component. Highly flammable mixtures are always present and may be ignited. Failure to follow these instructions may result in serious personal injury.
WARNING: When handling fuel, always observe fuel handling precautions and be prepared in the event of fuel spillage. Spilled fuel may be ignited by hot vehicle components or other ignition sources. Failure to follow these instructions may result in serious personal injury.
WARNING: Always disconnect the battery ground cable at the battery when working on an evaporative emission (EVAP) system or fuel-related component. Highly flammable mixtures are always present and may be ignited. Failure to follow these instructions may result in serious personal injury.
WARNING: Before working on or disconnecting any of the fuel tubes or fuel system components, relieve the fuel system pressure to prevent accidental spraying of fuel. Fuel in the fuel system remains under high pressure, even when the engine is not running. Failure to follow this instruction may result in serious personal injury.
  1. Release the fuel system pressure. For additional information, refer to FUEL SYSTEM PRESSURE RELEASE  .
  2. Disconnect the battery ground cable. For additional information, refer to BATTERY, BATTERY MOUNTING & BATTERY CABLES Article.
  3. Remove the rear seat lower cushion. For additional information, refer to SEAT SYSTEM - SEATS Article.
  4. Remove the Fuel Pump (FP) module access cover.
    Fig 1: Locating Fuel Pump Module Access Cover
    G06064443Courtesy of FORD MOTOR CO.
  5. NOTE: Clean the FP module connections, couplings, flange surfaces and the immediate surrounding area of any dirt or foreign material.
    Fig 2: Locating FP Module Electrical Connector
    G06261682Courtesy of FORD MOTOR CO.
  6. Disconnect the FP module electrical connector.
  7. Disconnect the fuel tank wiring harness electrical connector.
    Fig 3: Locating Fuel Tank Wiring Harness Electrical Connector
    G06261683Courtesy of FORD MOTOR CO.
  8. Disconnect the Fuel Tank Pressure (FTP) sensor electrical connector.
    Fig 4: Locating Fuel Tank Pressure Sensor Electrical Connector
    G06261684Courtesy of FORD MOTOR CO.
  9. NOTE: Place absorbent toweling in the immediate surrounding area in case of fuel spillage.
    Fig 5: Locating Fuel Tank Jumper Tube-To-FP Module Quick Connect Coupling
    G06261685Courtesy of FORD MOTOR CO.
  10. Disconnect the fuel tank jumper tube-to-FP module quick connect coupling. For additional information, refer to QUICK CONNECT COUPLING  .
  11. Attach the Fuel Storage Tanker tube to the FP module outlet fitting and remove one fourth (approximately 5 gallons) of the fuel from a completely full tank, lowering the fuel level below the FP module flange.
    Fig 6: Locating Fuel Storage Tanker Tube
    G06261686Courtesy of FORD MOTOR CO.
  12. NOTE: Carefully install the Fuel Tank Sender Unit Wrench to avoid damaging the Fuel Pump (FP) module when removing the lock ring.
    NOTE: Make sure to install a new FP module O-ring seal.
    Fig 7: Removing FP Module Lock Ring Using Fuel Tank Sender Unit Wrench
    G06261687Courtesy of FORD MOTOR CO.
  13. Install the Fuel Tank Sender Unit Wrench and remove the FP module lock ring.
  14. NOTE: The Fuel Pump (FP) module must be handled carefully to avoid damage to the float arm and filter.
    Fig 8: Locating Fuel Pump Module Tube
    G06756912Courtesy of FORD MOTOR CO.
  15. Position the FP module, insert the tube from the fuel storage tanker into the FP module aperture and remove as much fuel as possible from the fuel tank.