LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2005 >> Crown Victoria Base, 4.6 W >> Repair and Diagnosis >> Body & Frame >> Seats >> Seat System >> Disassembly And Assembly >> Front Seat Backrest >> Disassembly

Front Seat Backrest: Disassembly

WARNING: Always wear safety glasses when repairing an air bag supplemental restraint system (SRS) vehicle and when handling an air bag module. This will reduce the risk of injury in the event of an accidental deployment.
WARNING: Carry a live side air bag module with the air bag and tear seam pointed away from your body. This will reduce the risk of injury in the event of an accidental deployment.
WARNING: After deployment, the air bag surface can contain deposits of sodium hydroxide, a product of the gas generant combustion that is irritating to the skin. Wash your hands with soap and water afterwards.
WARNING: Never probe the connectors on the air bag module. Doing so can result in air bag deployment, which can result in personal injury.
WARNING: Front seat backrest trim covers installed on seats with side air bags cannot be repaired. The front seat backrest trim covers are to be installed new. Cleaning is permissible.
WARNING: To reduce the risk of personal injury, do not use any memory saver devices.
NOTE: If a seat equipped with a supplemental restraint system (SRS) component is being serviced, the SRS must be depowered. 
NOTE: The air bag warning lamp illuminates when the RCM fuse is removed and the ignition switch is ON. This is normal operation and does not indicate a supplemental restraint system (SRS) fault.
NOTE: If a side air bag deployment took place the seatback pad, trim cover, and side air bag module must be replaced. The seatback frame should be replaced if necessary.
NOTE: The SRS must be fully operational and free of faults before releasing the vehicle to the customer.
NOTE: Driver side shown, passenger side similar. All vehicles

    All Vehicles 

  1. Position the seat to access the fasteners.
  2. Depower the SRS. For additional information, refer to Supplemental Restraint System (SRS) Depowering and Repowering in the General Procedures portion of SUPPLEMENTAL RESTRAINT SYSTEM .
  3. Remove the front seat backrest. For additional information, refer to FRONT SEAT BACKREST .
  4. Police Vehicles 

  5. Remove the head restraint locking clip (outboard side driver, inboard side passenger).
    Fig 1: Removing Head Restraint Locking Clip (Outboard Side Driver, Inboard Side Passenger)
    G03880435Courtesy of FORD MOTOR CO.
  6. All Vehicles 

  7. Pull the head restraint out to end of travel. Press the release button and then pull the head restraint rod past its stop position.
    Fig 2: Locating Head Restraint Sleeve Tab
    G03880436Courtesy of FORD MOTOR CO.
  8. Remove the inboard hog rings that attach the foam pad to the seat backrest frame.
    Fig 3: Removing Inboard Hog Rings That Attach Foam Pad To Seat Backrest Frame
    G03880437Courtesy of FORD MOTOR CO.
  9. Vehicles With Seat Side Air Bags 

    NOTE: Install new side air bag nuts if installing a new side air bag module. If the existing side air bag is being reinstalled, retain the existing nuts.
    Fig 4: Removing Side Air Bag Module Nuts
    G03881246Courtesy of FORD MOTOR CO.
  10. Remove the side air bag module nuts.
  11. Position the side air bag module and deployment chute away from the mounting bracket and seat back frame.
    Fig 5: Positioning Side Air Bag Module And Deployment Chute Away From Mounting Bracket And Seat Back Frame
    G03881247Courtesy of FORD MOTOR CO.
  12. Position the seat back trim cover and seat back pad forward enough to access the side air bag module.
    Fig 6: Positioning Seat Back Trim Cover And Seat Back Pad Forward Enough To Access Side Air Bag Module
    G03881307Courtesy of FORD MOTOR CO.
  13. Remove the side air bag module from the deployment chute.
    • Pull the side air bag module mounting studs back through the deployment chute openings and remove the side air bag module from the deployment chute.
      Fig 7: Removing Side Air Bag Module From Deployment Chute
      G03880441Courtesy of FORD MOTOR CO.
  14. Disconnect and remove the side air bag module.
    Fig 8: Disconnecting Side Air Bag Module
    G03880442Courtesy of FORD MOTOR CO.
  15. NOTE: Make note of the side air bag wire harness routing for installation.
  16. If necessary, release the pin-type retainers from the backrest frame and remove the side air bag wire harness.
  17. All Vehicles 

  18. From inside the seat backrest, pinch the headrest guide pin ends and remove the sleeves.
    Fig 9: Identifying Head Restraint Sleeves
    G03932811Courtesy of FORD MOTOR CO.
  19. Remove the backrest foam pad and trim cover.
    • Separate the trim cover from the backrest foam pad.
  20. Vehicles With Power Lumbar 

  21. Detach the lumbar motor bracket clip.
    Fig 10: Detaching Lumbar Motor Bracket Clip
    G03880356Courtesy of FORD MOTOR CO.
  22. Detach the two lumbar support bracket clips and slide the lumbar assembly up and off.
    Fig 11: Detaching Lumbar Support Bracket Clips And Slide Lumbar Assembly Up And Off
    G03880445Courtesy of FORD MOTOR CO.