LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2003 >> ZX2 Automatic >> Repair and Diagnosis >> External Pages >> Different car >> Section 292 (Engine-2.3L) >> In-Vehicle Repair >> Crankshaft Pulley >> Installation

Crankshaft Pulley: Installation

WARNING: This page is about a different car, the 2003 Ford Focus. However, it is still accessible from the selected car via links, so may be relevant.
    NOTE: Do not reuse the crankshaft damper bolt.
    NOTE: Apply clean engine oil on the seal area before installing.
    Fig 1: Install Crankshaft Pulley
    G01611316Courtesy of FORD MOTOR CO.
  1. Install the crankshaft pulley and hand-tighten the bolt.
  2. CAUTION: Only hand-tighten the bolt or damage to the front cover can occur.
    NOTE: This step will correctly align the crankshaft pulley to the crankshaft.
    Fig 2: Installing Bolt Through Crankshaft Pulley
    G01611317Courtesy of FORD MOTOR CO.
  3. Install a standard 6 mm (0.23 in) x 18 mm (0.7 in) bolt through the crankshaft pulley and thread it into the front cover. Rotate the pulley as necessary to align the bolt holes.
  4. CAUTION: Failure to hold the crankshaft pulley in place during bolt tightening can result in damage to the engine.
  5. Using the special tools to hold the crankshaft pulley in place, tighten the pulley bolt in two stages:
    • Stage 1: Tighten to 100 Nm (74 lb-ft).
    • Stage 2: Tighten an additional 90 degrees.
      Fig 3: Tightening Pulley Bolt
      G01611318Courtesy of FORD MOTOR CO.
  6. Remove the special tools from the crankshaft pulley.
  7. Remove the 6 mm (0.23 in) x 18 mm (0.7 in) bolt.
  8. Remove the special tool.
    Fig 4: Remove Special Tool
    G01611319Courtesy of FORD MOTOR CO.
  9. Remove the special tool from the camshafts.
    Fig 5: Remove Special Tool From Camshafts
    G01611320Courtesy of FORD MOTOR CO.
  10. NOTE: Only turn the engine in the normal direction of rotation.
  11. Turn the engine two complete revolutions.
  12. Install the special tool.
    Fig 6: Install Special Tool
    G01611321Courtesy of FORD MOTOR CO.
  13. CAUTION: Only hand-tighten the bolt or damage to the front cover can occur.
    NOTE: If it is not possible to install the bolt, correct the engine timing.
    Fig 7: Checking Position Of Crankshaft Pulley
    G01611322Courtesy of FORD MOTOR CO.
  14. Using the 6 mm (0.23 in) x 18 mm (0.7 in) bolt, check the position of the crankshaft pulley.
  15. NOTE: If it is not possible to install the special tool, correct the engine timing.
    Fig 8: Checking Position Of Camshafts
    G01611323Courtesy of FORD MOTOR CO.
  16. Using the special tool, check the position of the camshafts.
  17. Remove the special tool.
    Fig 9: Remove Special Tool
    G01611324Courtesy of FORD MOTOR CO.
  18. Remove the 6 mm (0.23 in) x 18 mm (0.7 in) bolt.
    Fig 10: Remove Bolt
    G01611325Courtesy of FORD MOTOR CO.
  19. Remove the special tool.
    Fig 11: Remove Special Tool
    G01611326Courtesy of FORD MOTOR CO.
  20. Install the engine plug bolt.
    Fig 12: Install Engine Plug Bolt
    G01611327Courtesy of FORD MOTOR CO.
  21. Raise the engine.
  22. Install the RH motor mount nuts.
    Fig 13: Install RH Motor Mount Nuts
    G01611328Courtesy of FORD MOTOR CO.
  23. Install the LH motor mount center nut.
    Fig 14: Install LH Motor Mount Center Nut
    G01611329Courtesy of FORD MOTOR CO.
  24. Tighten the lower engine mount nuts.
    1. Position the lower engine mount.
    2. Tighten the lower engine mount nuts.
      Fig 15: Tightening Lower Engine Mount Nuts
      G01611330Courtesy of FORD MOTOR CO.
  25. Remove the special tool.
    Fig 16: Remove Special Tool
    G01611331Courtesy of FORD MOTOR CO.
  26. Install the battery tray.
    Fig 17: Install Battery Tray
    G01611332Courtesy of FORD MOTOR CO.
  27. Install the degas bottle. For additional information, refer to ENGINE COOLING .
  28. Install the valve cover. For additional information, refer to VALVE COVER .
  29. Install the accessory drive belt. For additional information, refer to ACCESSORY DRIVE .
  30. Install the fan and shroud. For additional information, refer to ENGINE COOLING .