LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2002 >> Taurus SES, 3.0 S >> Repair and Diagnosis >> Body & Frame >> Door Locks >> Anti-Theft Systems - Passive >> System Tests >> Test C: Unprogrammed Encoded Ignition Key (DTC B1601)

Test C: Unprogrammed Encoded Ignition Key (DTC B1601)

NOTE: Power Control Module (PCM) disables engine for 20 seconds every time DTC B1601 is set. The ignition switch must remain in the RUN position for at least 20 seconds before an attempt is made to start the vehicle with any encoded ignition key. Check PCM PID ANTISCAN for this unprogrammed key time-out status.
NOTE: Large metallic objects, a second Passive Anti-Theft System (PATS) ignition key, or devices such as electronic credit cards or gas speed credit pass on the same key ring may cause vehicle starting problem and possibly set this code. Ensure encoded ignition key is an approved Ford encoded ignition key. Encoded keys from Rotunda, Ilco, and Strattec are also approved keys.
  1. Turn ignition switch to LOCK position. Connect Worldwide Diagnostic System (WDS) tester or New Generation Star (NGS) tester to Data Link Connector (DLC). See Figure. Turn ignition switch to RUN position. Perform Powertrain Control Module (PCM) self-test. Retrieve, record and clear continuous DTCs. Turn ignition switch to LOCK position and then back to RUN position. Retrieve continuous DTCs. If DTC B1601 is retrieved, go to next step. If DTC B1601 is not retrieved, system is operating properly. Check all encoded ignition keys, by starting vehicle to verify all encoded ignition keys are programmed. After repair, clear DTCs and retest system for normal operation.
  2. Using WDS or NGS tester, monitor PCM PID NUMKEYS. If PID does not indicate 8 keys, go to next step. If PID indicates 8 keys, erase and reprogram all encoded ignition keys. See KEY PROGRAMMING - USING DIAGNOSTIC EQUIPMENT  under PROGRAMMING. After repair, clear DTCs and retest system for normal operation.
  3. Ensure there are at least 2 programmed encoded ignition keys available with vehicle. If at least 2 programmed encoded ignition keys are available with vehicle, go to next step. If at least 2 programmed encoded ignition keys are not available with vehicle, obtain a NEW approved Ford encoded ignition key cut. Program encoded ignition keys. See SPARE KEY PROGRAMMING - USING DIAGNOSTIC EQUIPMENT  under PROGRAMMING, then go to step  5.
  4. Using WDS or NGS tester, monitor PCM PID SPARE_KY. If PID indicates ENABLE, reprogram ignition keys. See KEY PROGRAMMING - USING 2 PROGRAMMED KEYS  under PROGRAMMING, then go to next step. If PID indicates DISABLE, enable spare key programming switch control. See KEY PROGRAMMING - SWITCH STATE CONTROL  under PROGRAMMING. After repair, clear DTCs and retest system for normal operation.
  5. Using first encoded ignition key, turn ignition switch to RUN position for 3 seconds. Turn ignition switch to LOCK position. Using second encoded ignition key, turn ignition switch to RUN position for 3 seconds. Attempt to start vehicle using second encoded ignition key. If vehicle does not start, go to next step. If vehicle starts, system is operating properly. If additional encoded ignition keys are needed, see KEY PROGRAMMING - USING 2 PROGRAMMED KEYS  under PROGRAMMING. After repair, clear DTCs and retest system for normal operation.
  6. Leave ignition switch at RUN position. Using WDS or NGS tester, retrieve, record and clear continuous DTCs. Turn ignition switch to LOCK position and then back to RUN position. Retrieve continuous DTCs. If DTC B1601 is retrieved, replace PCM. See POWERTRAIN CONTROL MODULE  under REMOVAL & INSTALLATION. After PCM replacement, reprogram ignition keys. See KEY PROGRAMMING - USING DIAGNOSTIC EQUIPMENT . If DTC B1601 is not retrieved, system is operating properly. If any DTCs other than PATS are retrieved, see appropriate SELF-DIAGNOSTICS article in ENGINE PERFORMANCE. After repair, clear DTCs and retest system for normal operation.