LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2001 >> Crown Victoria Base, 4.6 W >> Repair and Diagnosis >> Body & Frame >> Windows >> Power Window System >> System Tests >> Test E: Passenger's Window Is Inoperative

Test E: Passenger's Window Is Inoperative

NOTE: Ensure lock-out switch is in OFF position before testing.
  1. Turn ignition switch to ON position. Operate passenger's window from driver's door master window switch. If passenger's window does not operate, go to next step. If passenger's window operates, go to step  16 .
  2. Turn ignition switch to LOCK position. Disconnect passenger's window motor harness connector C610. Turn ignition switch to ON position. Measure voltage between ground and passenger's window motor harness connector C610 Red/Yellow wire terminal while pressing driver's door master window switch to passenger's window DOWN position. If battery voltage does not exist, go to next step. If battery voltage exists, go to step  8 .
  3. Disconnect passenger's window/door lock switch harness connector C606. Measure voltage between ground and passenger's window/door lock switch harness connector C606 terminal No. 11 (Tan/Light Blue wire) while pressing driver's door master window switch to passenger's window DOWN position. See Fig 1 . If battery voltage does not exist, go to next step. If battery voltage exists, go to step  6 .
  4. Turn ignition switch to LOCK position. Disconnect driver's door master window switch harness connector C503. Measure resistance between ground and passenger's window/door lock switch harness connector C606 terminal No. 11 (Tan/Light Blue wire). If resistance is greater than 10 k/ohms, go to next step. If resistance is 10 k/ohms or less, repair short to ground in Tan/Light Blue wire.
  5. Measure resistance in Tan/Light Blue wire between passenger's window/door lock switch harness connector C606 terminal No. 11 and driver's door master window switch harness connector C503 terminal No. 11. See Figure and Fig 1 . If resistance is 5 ohms or less, replace driver's door master window switch. If resistance is greater than 5 ohms, repair open in Tan/Light Blue wire.
  6. Measure resistance between ground and passenger's window motor harness connector C610 Red/Yellow wire terminal. If resistance is greater than 10 k/ohms, go to next step. If resistance is 10 k/ohms or less, repair short to ground in Red/Yellow wire.
  7. Measure resistance of Red/Yellow wire between passenger's window motor harness connector C610 terminal and passenger's window/door lock switch harness connector C606 terminal No. 12. If resistance is 5 ohms or less, replace passenger's door master window switch. If resistance is greater than 5 ohms, repair open in Red/Yellow wire.
  8. Measure resistance between ground and passenger's window motor harness connector C610 Red/Yellow wire terminal. If resistance is 5 ohms or less, go to next step. If resistance is greater than 5 ohms, replace driver's door master window switch.
  9. Measure voltage between ground and passenger's window motor harness connector C610 Yellow/Red wire terminal while pressing driver's door master window switch to passenger's window UP position. If battery voltage exists, go to next step. If battery voltage does not exist, go to step  11 .
  10. Measure resistance between ground and passenger's window motor harness connector C610 Yellow/Red wire terminal. If resistance is 5 ohms or less, replace passenger's window motor. If resistance is greater than 5 ohms, replace driver's door master window switch.
  11. Disconnect passenger's window/door lock switch harness connector C606. Measure voltage between ground and passenger's window/door lock switch harness connector C606 terminal No. 9 (White/Yellow wire) while pressing driver's door master window switch to passenger's window UP position. See Fig 1 . If battery voltage exists, go to next step. If battery voltage does not exist, go to step  14 .
  12. Measure resistance between ground and passenger's window/door lock switch harness connector C606 terminal No. 8 (Yellow/Red wire). If resistance is greater than 10 k/ohms, go to next step. If resistance is 10 k/ohms or less, repair short to ground in Yellow/Red wire.
  13. Measure resistance in Yellow/Red wire between passenger's window motor harness connector C610 and passenger's window/door lock switch harness connector C606 terminal No. 8. If resistance is 5 ohms or less, replace passenger's door master window switch. If resistance is greater than 5 ohms, repair open in Red/Yellow wire.
  14. Disconnect driver's door master window switch harness connector C503. Measure resistance between ground and passenger's window/door lock switch harness connector C606 terminal No. 9 (White/Yellow wire). If resistance is greater than 10 k/ohms, go to next step. If resistance is 10 k/ohms or less, repair short to ground in White/Yellow wire.
  15. Measure resistance in White/Yellow wire between passenger's window/door lock switch harness connector C606 terminal No. 9 and driver's door master window switch harness connector C503 terminal No. 9. See Figure and Fig 1 . If resistance is 5 ohms or less, replace driver's door master window switch. If resistance is greater than 5 ohms, repair open in White/Yellow wire wire.
  16. Operate rear power window from individual window control switches. If rear windows operate, go to next step. If rear windows do not operate, go to step  18 .
  17. Disconnect passenger's window/door lock switch harness connector C606. Turn ignition switch to ON position. Measure voltage between passenger's window/door lock switch harness connector C606 terminal No. 10 (Red/Light Blue wire). See Fig 1 . If battery voltage exists, replace passenger's window/door lock switch. If battery voltage does not exist, repair open in Red/Light Blue wire.
  18. Disconnect passenger's window/door lock switch harness connector C606. Disconnect driver's door master window switch harness connector C503. Measure resistance in Red/Light Blue wire between passenger's window/door lock switch harness connector C606 terminal No. 10 and driver's door master window switch harness connector C503 terminal No. 20. See Figure and Fig 1 . If resistance is 5 ohms or less, go to next step. If resistance is greater than 5 ohms, repair open in Red/Light Blue wire.
  19. Measure resistance between ground and passenger's window/door lock switch harness connector C606 terminal No. 10 (Red/Light Blue wire). If resistance is greater than 10 k/ohms, replace driver's door master window switch. If resistance is 10 k/ohms or less, repair short to ground in Red/Light Blue wire.
Fig 1: Identifying Passenger's Window/Door Lock Switch Harness Connector C606 Terminals
G95C13542Courtesy of FORD MOTOR CO.