LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2000 >> Focus ZTS, Standard >> Repair and Diagnosis >> Body & Frame >> Mirrors >> Power Mirror System >> Symptom Tests >> Test C: Single Mirror Inoperative With Switch Logic

Test C: Single Mirror Inoperative With Switch Logic

NOTE: Wire color changes between mirror control switch and power mirror harness connectors at splice S200. See WIRING DIAGRAMS .
  1. Turn ignition switch to LOCK position. Disconnect mirror control switch 8-pin harness connector C741. Test mirror control switch. See MIRROR CONTROL SWITCH  under COMPONENT TESTS. If switch is defective, replace mirror control switch. See MIRROR CONTROL SWITCH & MIRROR ASSEMBLY  under REMOVAL & INSTALLATION. If switch is okay, and driver's mirror does not move up or down go to next step. If switch is okay and driver's mirror does not move left or right, go to step  5. If switch is okay and passenger's mirror does not move up or down, go to step  8. If switch is okay and passenger's mirror does not move left or right, go to step  11.
  2. Connect mirror control switch. Disconnect driver's mirror 5-pin harness connector C807. Turn ignition switch to RUN position. Measure voltage between driver's mirror harness connector C807 terminals No. 1 (White wire) and No. 2 (Blue/Red wire) while operating mirror up and down. See Figure. When mirror control switch is moved to UP position, more than 10 volts should exist and polarity should reverse when moved to DOWN position. If voltage is not as specified, go to next step. If voltage is as specified, replace driver's mirror. See MIRROR CONTROL SWITCH & MIRROR ASSEMBLY  under REMOVAL & INSTALLATION.
  3. Turn ignition switch to LOCK position. Disconnect mirror control switch 8-pin harness connector C741. Measure resistance of Blue/Red wire between mirror control switch harness connector C741 terminal No. l and driver's mirror harness connector C807 terminal No. 2. See Figure and Figure . If resistance is less than 5 ohms, go to next step. If resistance is 5 ohms or greater, repair open or high resistance in Blue/Red wire. See WIRING DIAGRAMS .
  4. Measure resistance between mirror control switch harness connector C741 terminal No. 3 (White/Red wire) and driver's mirror harness connector C807 terminal No. 1 (White wire). If resistance is less than 5 ohms, replace driver's mirror. See MIRROR CONTROL SWITCH & MIRROR ASSEMBLY  under REMOVAL & INSTALLATION. If resistance is 5 ohms or greater, repair open or high resistance in White/Red or White wire. See WIRING DIAGRAMS .
  5. Disconnect driver's mirror 5-pin harness connector. Turn ignition switch to RUN position. Measure voltage between driver's mirror harness connector C807 terminals No. 1 (White wire) and No. 3 (Yellow/Blue wire) while operating mirror left and right. See Figure. When mirror control switch is moved to LEFT position, more than 10 volts should exist and polarity should reverse when moved to RIGHT position. If voltage is not as specified, go to next step. If voltage is as specified, replace driver's mirror. See MIRROR CONTROL SWITCH & MIRROR ASSEMBLY  under REMOVAL & INSTALLATION.
  6. Turn ignition switch to LOCK position. Disconnect mirror control switch 8-pin harness connector C741. Measure resistance of Yellow/Blue wire between mirror control switch harness connector C741 terminal No. 7 and driver's mirror harness connector C807 terminal No. 3. See Figure and Figure . If resistance is less than 5 ohms, go to next step. If resistance is 5 ohms or greater, repair open or high resistance in Yellow/Blue wire. See WIRING DIAGRAMS .
  7. Measure resistance between mirror control switch harness connector C741 terminal No. 3 (White/Red wire) and driver's mirror harness connector C807 terminal No. 1 (White wire). If resistance is less than 5 ohms, replace driver's mirror. See MIRROR CONTROL SWITCH & MIRROR ASSEMBLY  under REMOVAL & INSTALLATION. If resistance is 5 ohms or greater, repair open or high resistance in White/Red or White wire. See WIRING DIAGRAMS .
  8. Disconnect passenger's mirror 5-pin harness connector C808. Turn ignition switch to RUN position. Measure voltage between passenger's mirror harness connector C808 terminals No. 1 (White/Green wire) and No. 2 (Blue/Yellow wire) while operating switch to UP and DOWN position. See Figure. When mirror control switch is moved to UP position, more than 10 volts should exist and polarity should reverse when moved to DOWN position. If voltage is not as specified, go to next step. If voltage is as specified, replace passenger's mirror. See MIRROR CONTROL SWITCH & MIRROR ASSEMBLY  under REMOVAL & INSTALLATION.
  9. Turn ignition switch to LOCK position. Disconnect mirror control switch 8-pin harness connector C741. Measure resistance of Blue/Yellow wire between mirror control switch harness connector C741 terminal No. 2 and passenger's mirror harness connector C808 terminal No. 2. If resistance is less than 5 ohms, go to next step. If resistance is 5 ohms or greater, repair open or high resistance in Blue/Yellow wire. See WIRING DIAGRAMS .
  10. Measure resistance between mirror control switch harness connector C741 terminal No. 3 (White/Red wire) and passenger's mirror harness connector C808 terminal No. 1 (White/Green wire). See Figure. If resistance is less than 5 ohms, replace passenger's mirror. See MIRROR CONTROL SWITCH & MIRROR ASSEMBLY  under REMOVAL & INSTALLATION. If resistance is 5 ohms or greater, repair open or high resistance in White/Red or White/Green wire. See WIRING DIAGRAMS .
  11. Disconnect passenger's 5-pin harness connector C808. Turn ignition switch to RUN position. Measure voltage between passenger's mirror harness connector C808 terminals No. 3 (Yellow/Violet wire) and No. 1 (White/Green wire) while operating mirror left and right. See Figure. When mirror control switch is moved to LEFT position, more than 10 volts should exist and polarity should reverse when moved to RIGHT position. If voltage is not as specified, go to next step. If voltage is as specified, replace passenger's mirror. See MIRROR CONTROL SWITCH & MIRROR ASSEMBLY  under REMOVAL & INSTALLATION.
  12. Turn ignition switch to LOCK position. Disconnect mirror control switch 8-pin harness connector C741. Measure resistance of Yellow/Violet wire between mirror control switch harness connector C741 terminal No. 5 and passenger's mirror harness connector C808 terminal No. 3. See Figure and Figure . If resistance is less than 5 ohms, go to next step. If resistance is 5 ohms or greater, repair open or high resistance in Yellow/Violet wire. See WIRING DIAGRAMS .
  13. Measure resistance between mirror control switch harness connector C741 terminal No. 3 (White/Red wire) and passenger's mirror harness connector C808 terminal No. 1 (White/Green wire). See Figure and Figure . If resistance is less than 5 ohms, replace passenger's mirror. See MIRROR CONTROL SWITCH & MIRROR ASSEMBLY  under REMOVAL & INSTALLATION. If resistance is 5 ohms or greater, repair open or high resistance in White/Red or White/Green wire. See WIRING DIAGRAMS .