Test J - Fuel Pump CKT (Relay & Inertia Switch)
- Fuel Pump Relay
- Inertia Switch
- Harness Circuits (Batt +, VPWR, FUEL PUMP, GND, POWER-to-PUMP)
- ECA
| Application (Test Pin No.) | Wire Color | |
|---|---|---|
| Pin 22 | ||
| TBI & PFI | Tan/Light Green | |
| All Others | Tan/Light Green | |
| Pin 8, 19 or 50, Power-to-Pump | Pink/Black | |
| Batt (+) Ckt (MA PFI) | White/Green | |
| Pin 37 or 57 | ||
| MA PFI | White/Red | |
| All Others | Red | |
- 1) No Fuel Pump Pressure: Check Fuel Pump Electrical Operation Turn key from OFF to RUN position several times (DO NOT turn to START position). If fuel pumps run briefly each time key is turned to RUN position, fuel pump circuit is okay. If not, go to next step.
- 2) Check For VPWR to ECA
With key off, install breakout box and reconnect ECA. Set DVOM on 20-volt scale. Turn key on, leaving engine off. Measure voltage between test pins No. 37 and 40 at the breakout box. Measure voltage between test pins No. 57 and 60 at the breakout box. If both voltage readings are greater than 10.5 volts, go to step 5. If voltage is not greater than 10.5 volts, go to TEST B, step 1.NOTE: A break in step numbering sequence occurs at this point. Procedure skips from step 2 to step 5. No test procedures have been omitted.
- 5) Check Voltage to POWER-to-PUMP Circuit With KOEO, breakout box installed and ECA connected, set DVOM on 20-volt scale. Measure voltage between chassis ground and POWER-to-PUMP circuit at fuel pump relay while cranking engine. If reading is less than 8 volts, go to step 6. If reading is 8 volts or more, check the following: open in POWER-to-PUMP circuit, open in fuel pump and open fuel pump ground circuit.
- 6) Checking BATT (+) Circuit to Fuel Pump Relay Turn key on, leaving engine off. Leave breakout box installed and ECA connected. Locate fuel pump relay. Set DVOM on 20-volt scale. Measure voltage between chassis ground and BATT (+) circuit at fuel pump relay. If reading is less than 10.5 volts, repair open in BATT (+) circuit between fuel pump relay and battery positive post. Repeat QUICK TEST PROCEDURES . If reading is 10.5 volts or greater, go to next step for PFI engines or step 11 for all others.
- 7) Code 87: Checking VPWR Circuit to Fuel Pump Relay Code 87 indicates a fuel pump primary circuit failure. Possible causes for this fault are: inertia switch not reset or electrically open, faulty fuel pump relay or ECA. Open or shorted circuit. Turn key on, leaving engine off. Leave breakout box installed and ECA connected. Locate fuel pump relay. Set DVOM on 20-volt scale. Measure voltage between chassis ground and VPWR circuit (ignition START/RUN circuit on TBI and PFI) at fuel pump relay. If reading is 10.5 volts or more, go to next step. If reading is less than 10.5 volts, ensure inertia switch is on. If inertia switch will not reset, replace switch. If switch is okay, repair open in VPWR circuit (ignition switch START/RUN circuit and fuel pump relay on TBI and PFI engines between EEC power relay and fuel pump relay. Repeat QUICK TEST PROCEDURES .
- 8) Check FUEL PUMP Circuit Continuity Turn key off and wait 10 seconds. Disconnect ECA 60-pin connector. Inspect for corroded or damaged connector pins and repair as necessary. Install breakout box, leaving ECA disconnected. With DVOM on 200-ohm scale, measure resistance between FUEL PUMP circuit at pump relay and test pin No. 22 at breakout box. If reading is 5 ohms or more, repair open in FUEL PUMP circuit. Repeat QUICK TEST PROCEDURES . If reading is less than 5 ohms, go to next step.
- 9) Check For Short to Power With key off, disconnect ECA and fuel pump relay. Install breakout box and set DVOM on 20-volt scale. Turn key on. Measure voltage between test pin No. 22 and battery negative terminal. If voltage is less than one volt, go to next step. If not, repair short circuit. Reconnect ECA and attempt to start vehicle. If vehicle fails to start, replace ECA. Rerun QUICK TEST PROCEDURES .
- 10) Check For Shorts to Ground Turn key off and wait 10 seconds. Leave breakout box installed and ECA disconnected. Disconnect fuel pump relay. With DVOM on 200-k/ohm scale, measure resistance between test pin No. 22 and test pins No. 40 and 60. If reading is less than 10 k/ohms, repair short in FUEL PUMP circuit. Repeat QUICK TEST PROCEDURES . If reading is 10 k/ohms or more, go to next step.
- 11) Check Voltage at POWER-to-PUMP Circuit
Turn key off. Leave breakout box installed and ECA disconnected. Install a jumper wire between test pin No. 22 and test pins No. 40 or 60. Set DVOM on 20-volt scale. With KOEO, measure voltage between chassis ground and POWER-to-PUMP circuit at fuel pump relay. If reading is 10.5 volts or more, replace ECA and repeat QUICK TEST PROCEDURES . If reading is less than 10.5 volts, replace fuel pump relay. Connect ECA and repeat QUICK TEST.NOTE: A break in step numbering sequence occurs at this point. Procedure skips from step 11 to step 20. No test procedures have been omitted.
- 20) Code 95: Does Engine Start?
A KOEO Code 95 indicates that one of the following has occurred:
- No Starts
- Inertia switch not reset or electrically open.
- Open circuit in or between ECA and fuel pump.
- Faulty ground connection at fuel pump.
- Vehicle Starts
- Fuel pump secondary circuit shorted to power.
- Fuel pump relay contacts always closed.
- Open in Fuel Pump Monitor (FPM) circuit between ECA and connection to POWER-to-PUMP circuit.
- On PFI engines only, fuel pump circuit (pin No. 22) shorted to ground.
- Faulty ECA.
If engine starts, go to next step. If not, go to step 25.
- No Starts
- 21) Verify Fuel Pump is Off With key off, listen for fuel pump noise. If fuel pump is off, go to step 23. If fuel pump is on, go to next step.
- 22) Check For Fuel Pump Relay Always Closed Turn key off. Disconnect fuel pump relay. If fuel pump turns off when relay is disconnected, replace fuel pump relay. Repeat QUICK TEST PROCEDURES . If fuel pump does not turn off, repair short in POWER-to-PUMP or FPM circuit.
- 23) Check Continuity of Fuel Pump Monitor (FPM) Circuit Turn key off and wait 10 seconds. Disconnect ECA 60-pin connector. Inspect connector for damaged pins, corrosion, or loose wires. Install breakout box and leave ECA disconnected. Disconnect fuel pump relay. Set DVOM on 200-ohm scale and measure resistance between test pin No. 8 (No. 19 on MA PFI at the breakout box and POWER-to-PUMP circuit at the fuel pump relay vehicle harness connector. If resistance is less than 5 ohms, go to next step for MA PFI engines. On all other engines, replace ECA, remove breakout box, reconnect fuel pump relay and repeat QUICK TEST PROCEDURES . If resistance is greater than 5 ohms, repair open circuit, remove breakout box, reconnect all components and rerun QUICK TEST.
- 24) Check Fuel Pump Primary Circuit For Short to Ground Turn key off and wait 10 seconds. Install breakout box and disconnect ECA. Disconnect fuel pump relay and set DVOM on 200-k/ohm scale. Measure resistance between test pins No. 22 and 40 at the breakout box. If resistance is greater than 10 k/ohms, remove test set-up. Replace ECA, reconnect components and rerun QUICK TEST PROCEDURES . If resistance is less than 10 k/ohms, repair short circuit and reconnect components. Repeat QUICK TEST.
- 25) Check Inertia Switch Turn key off and wait 10 seconds. Locate and disconnect fuel pump inertia switch. Verify that switch is reset. Set DVOM on 200-ohm scale. Measure resistance of fuel pump inertia switch (on MA PFI engines, measure resistance between GND pin and FP pin). If resistance is less than 5 ohms, reconnect switch and go to next step. If not, replace or reset inertia switch. Repeat QUICK TEST PROCEDURES .
- 26) Check Continuity Between FPM Circuit & Ground
Turn key off. Install breakout box and disconnect ECA. Disconnect fuel pump relay. Set DVOM on 200-ohm scale and measure resistance between test pin No. 8 (test pin No. 19 on MA PFI) at the breakout box and battery negative terminal. If resistance is less than 10 ohms, replace ECA, remove breakout box, reconnect fuel pump relay and repeat QUICK TEST PROCEDURES . If resistance is more than 10 ohms, remove test set-up and check the following: open circuit in fuel pump, poor ground connection at fuel pump, or an open in POWER-to-PUMP circuit.NOTE: A break in step numbering sequence occurs at this point. Procedure skips from step 26 to step 30. No test procedures have been omitted.
- 30) Code 96: Checking BATT (+) to Fuel Pump Relay
Code 96 indicates a fuel pump secondary circuit failure between the BATT (+) supply and the FPM connection to the POWER-to-PUMP circuit. Possible causes for this fault are: faulty fuel pump relay, ECA, or open circuit.
Turn key off and wait 10 seconds. Locate fuel pump relay. With the DVOM on 20-volt scale, measure voltage between BATT (+) circuit at fuel pump relay and battery negative post. If voltage is greater than 10.5 volts, go to next step. If voltage is less than 10.5 volts, repair open circuit in BATT (+) circuit and rerun QUICK TEST PROCEDURES .
- 31) Check For Voltage at POWER-to-PUMP Circuit to Verify Fuel Pump Relay Operation With key off, set DVOM on 20-volt scale. Connect DVOM between POWER-to-PUMP circuit at fuel pump relay and battery negative post. Check voltage while turning key to ON position (for one second) and OFF position (10 seconds). Repeat cycle at least 5 times. If voltage is greater than 10.5 volts for approximately one second after key is turned to RUN position, replace ECA and rerun QUICK TEST PROCEDURES . If voltage is not to specification, inspect relay harness connector. If okay, replace fuel pump relay. Rerun QUICK TEST.
- 32) Check Continuity of POWER-to-PUMP Circuit
Turn key off and disconnect ECA 60-pin connector. Inspect connector for damaged pins, corrosion, or loose wires. Service as necessary. Install breakout box and leave ECA disconnected. Disconnect fuel pump relay. With DVOM on 200-ohm scale, measure resistance between test pin No. 8 (No. 19 on MA PFI) at breakout box and POWER-to-PUMP circuit at relay harness connector. If resistance is less than 5 ohms, remove test set-up, replace ECA, and rerun QUICK TEST PROCEDURES . If resistance is greater than 5 ohms, repair open circuit between FPM connecting splice and fuel pump relay. Rerun QUICK TEST.NOTE: A break in step numbering sequence occurs at this point. Procedure skips from step 32 to step 90. No test procedures have been omitted.
- 90) Continuous Memory Code 95: Check EEC-IV Harness
Code 95 indicates that one of the following conditions has occurred intermittently:
- Open circuit in or between the fuel pump and FPM circuit at the ECA.
- Faulty ground circuit at the fuel pump.
- FPM or POWER-to-PUMP circuit short to power.
- Fuel pump relay contacts stuck open.
- FUEL PUMP circuit activated when ECA expected circuit to be off.
Start engine and perform WIGGLE TEST on vehicle harness to fuel pump, and to pump ground circuit harness. Lightly tap inertia switch and pump to simulate road shock. Check for engine miss or stumble while performing test. With key off, check harness connectors for corrosion or damage. Isolate and repair any faults that are found, clear Code 95 and rerun QUICK TEST PROCEDURES . If no fault is found, go to next step.
- 91) Check FPM Circuit Turn key off. Disconnect ECA 60-pin connector. Inspect connector for damaged pins, corrosion, or loose wires. Install breakout box and leave ECA disconnected. With KOEO, connect a test light between test pin No. 8 (No. 19 on MA PFI) and test pin No. 37 at the breakout box. With test light lit, perform WIGGLE TEST on FPM circuit between pump and monitor. Light should go out if fault is found during WIGGLE TEST. Isolate and repair any found faults, remove test set-up and rerun QUICK TEST PROCEDURES . If no faults are found, go to next step.
- 92) Check For Shorts to Power With KOEO, breakout box installed and ECA disconnected, connect a test light between test pin No. 8 (No. 19 on MA PFI) and test pin No. 40. Observe test light, perform WIGGLE TEST on FPM circuit and POWER-to-PUMP circuit. Lightly tap the fuel pump relay to simulate road shock. If light goes on to indicate a fault is found, isolate and repair as necessary. Remove test set-up and rerun QUICK TEST PROCEDURES . If no faults are found, fault is intermittent and cannot be duplicated at this time. Clear Continuous Memory Codes and rerun QUICK TEST.
- 93) Continuous Memory Code 96: Check For Continuous Memory Code 87 If Code 87 is also present, go to step 26. If code 87 is not displayed, go to next step.
- 94) Check EEC-IV Harness
A Continuous Memory Code 96, without an accompanying Continuous Memory Code 87 indicates that during vehicle operation, one of the following has occurred:
- An open in the BATT + circuit between the BATT + and the fuel pump relay
- Fuel pump relay contacts opened
- Open in the POWER-to-PUMP circuit from the fuel pump relay to the FPM splice, if applicable.
With engine running attempt to cause a miss or stumble while performing WIGGLE TEST on pump harness and connectors. With key off, inspect all fuel pump connectors and BATT + for damage or corrosion. If a fault is found, isolate and repair it as necessary. Clear Continuous Memory Codes and rerun QUICK TEST PROCEDURES . If no fault is found, on MA PFI engines go to next step, On all other models, fault may not be duplicated at this time. Clear Continuous Memory Codes, Code 96 testing is complete.
- 95) Continuous Code 87: Check EEC-IV Harness
A Continuous Memory Code 87 indicates the primary fuel pump circuit has failed during vehicle operation. Possible causes for this fault are:
- An open in the VPWR circuit between the EEC power relay and the fuel pump relay
- Open coil in fuel pump relay
- Open in fuel pump circuit
- Faulty inertia switch
With engine running, attempt to cause a miss or stumble while performing WIGGLE TEST on VPWR circuit between EEC power relay and fuel pump relay. Wiggle fuel pump circuit harness (test pin No. 22) between ECA and the fuel pump relay. Lightly tap fuel pump relay to simulate road shock. With key off, inspect ECA 60-pin connector for damage or corrosion. If a fault is found, isolate and repair it. Rerun QUICK TEST PROCEDURES . If no fault is found, fault may not be duplicated at this time.