LEMON Manuals: Even more car manuals for everyone
Home >> Dodge and Ram >> 2013 >> 2500 HD Power Wagon >> Repair and Diagnosis >> Quick Lookups >> Technical Bulletins >> Campaigns >> Other Variant >> Restraints Control Systems >> Safety Recall T25/NHTSA 17V-302 Occupant Restraint Control Module (RC-T25-17)

Safety Recall T25/NHTSA 17V-302 Occupant Restraint Control Module (RC-T25-17)

WARNING: This page is about the 2500 HD SLT, 4D Pickup, 5.7L Eng VIN 2, which is a different variant/trim than selected.
Publication date: 2017-08-02
Reference number: RC-T25-17

SAFETY RECALL T25/NHTSA 17V-302 OCCUPANT RESTRAINT CONTROL MODULE

SAFETY RECALL T25/NHTSA 17V-302 OCCUPANT RESTRAINT CONTROL MODULE

SERVICE CAMPAIGN BULLETIN

Reference Number(s): RC-T25-17, Date of Issue:  June, 2017
CHRYSLER: 2013-2016 (DS) RAM 1500 Pickup, (DJ) RAM 2500 Pickup; 2014-2016 (D2) RAM 3500 Pickup

MODELS

2013-2016 (DS) RAM 1500 Pickup 

2013-2016 (DJ) RAM 2500 Pickup 

2014-2016 (D2) RAM 3500 Pickup 

NOTE: This recall applies only to the above vehicles equipped with roll rate sensing built from June 08, 2012 through July 10, 2015 (MDH 060801 through 071008  ).
IMPORTANT: Some of the involved vehicles may be in dealer new vehicle inventory. Federal law requires you to complete this recall service on these vehicles before retail delivery.  Dealers should also consider this requirement to apply to used vehicle inventory and should perform this recall on vehicles in for service. Involved vehicles can be determined by using the VIP inquiry process.

SUBJECT

The Occupant Restraint Control (ORC) module on about 1,030,000 of the above vehicles may activate a diagnostic trouble code (DTC) due to external stimulus which disables its ability to sense vehicle rollover events. When the DTC is set, airbag and seat belt pretensioner deployment based on rollover sensing is disabled for the ignition cycle in which the DTC was set. The loss of air bag and seat belt pretensioner deployment capability during a crash may increase the risk of injury or death.

REPAIR

The ORC module on involved vehicles must be reprogrammed with new software.

PARTS INFORMATION

No parts are required to perform this service procedure.

PARTS RETURN

No parts return required for this campaign.

SPECIAL TOOLS

The following special tools are required to perform this repair:

SERVICE PROCEDURE

Reprogram the ORC Module

NOTE: The wiTECH scan tool must be used to perform this recall. This procedure must be performed with the latest software release level. If the reprogramming flash for the ORC is aborted or interrupted, repeat the procedure. The ORC must be at the latest calibration level after completing this recall.
  1. Open the hood. Install a battery charger and verify that the charging rate provides 13.2 to 13.5 volts. Do not allow the charger to time out during the flash process. Set the battery charger timer (if so equipped) to continuous charge.
    NOTE: Use an accurate stand-alone voltmeter. The battery charger volt meter may not be sufficiently accurate. Voltages outside of the specified range will cause an unsuccessful flash. If voltage reading is too high, apply an electrical load by activating the park or headlamps and/or HVAC blower motor to lower the voltage.
  2. Connect the wiTECH micro pod II to the vehicle data link connector.
  3. Place the ignition in the "RUN"  position.
    NOTE: The following procedure steps are based on using the wiTECH 2.0 scan tool. If an earlier version of the wiTECH scan tool is used, procedure steps may be different.
  4. Open the wiTECH 2.0 website.
  5. Enter your "User id"  and "Password",  and then select "Finish"  at the bottom of the screen.
  6. From the "Vehicle Selection"  screen, select the vehicle to be updated.
  7. From the "Action Items"  screen, select the "Topology"  tab.
  8. From the "Topology"  screen, click on the "ORC"  icon.
  9. From the "ORC"  screen, select the "Flash"  tab, then compare the "Current Electronic Control Unit (ECU) Part Number"  with the "New ECU Part Number"  listed.
    • If the "Current ECU part Number"  is the same as the "New Part Number"  , proceed to Step  17.
    • If the "Current ECU part Number"  is NOT the same as the "New Part Number"  , continue with Step 10  .
  10. From the flash ECU agreement page, agree to terms by checking the box.
  11. Select "Flash ECU"  then follow the wiTECH screen instructions to complete the flash.
  12. Once the flash is complete, select the "View DTCs"  tab.
  13. Select "Clear All DTCs"  and then select "Close"  .
  14. From the "Topology"  screen, click on the "ABS"  icon.
  15. From the "ABS"  screen, select the "Misc Functions"  tab.
  16. Perform the "ABS Initialization"  routine and follow the screen prompts.
  17. Select "Clear All DTCs"  and then select "Close"  .
  18. Turn the ignition to the "OFF"  position and then remove the wiTECH micro pod II device from the vehicle.
  19. Remove the battery charger from the vehicle and then close the hood.
  20. Return the vehicle to the customer.

COMPLETION REPORTING AND REIMBURSEMENT

Claims for vehicles that have been serviced must be submitted on the DealerCONNECT Claim Entry Screen located on the Service tab. Claims paid will be used by FCA to record recall service completions and provide dealer payments.

Use one  of the following labor operation numbers and time allowances:

LABOR OPERATION NUMBER AND TIME ALLOWANCE

  Labor Operation Number  Time Allowance
ORC module update previously performed 18-T2-51-81 0.2 hours
Reprogram the ORC module 18-T2-51-82 0.2 hours
NOTE: See the Warranty Administration Manual, Recall Claim Processing Section, for complete recall claim processing instructions.

DEALER NOTIFICATION

To view this notification on DealerCONNECT, select "Global Recall System" on the Service tab, then click on the description of this notification.

OWNER NOTIFICATION AND SERVICE SCHEDULING

All involved vehicle owners known to FCA are being notified of the service requirement by first class mail. They are requested to schedule appointments for this service with their dealers. A generic copy of the owner letter is attached.

VEHICLE LISTS, GLOBAL RECALL SYSTEM, VIP AND DEALER FOLLOW UP

All involved vehicles have been entered into the DealerCONNECT Global Recall System (GRS) and Vehicle Information Plus (VIP) for dealer inquiry as needed.

GRS provides involved dealers with an updated  VIN list of their incomplete  vehicles. The owner's name, address and phone number are listed if known. Completed vehicles are removed from GRS within several days of repair claim submission.

To use this system, click on the "Service"  tab and then click on "Global Recall System."  Your dealer's VIN list for each recall displayed can be sorted by: those vehicles that were unsold at recall launch, those with a phone number, city, zip code, or VIN sequence.

Dealers must  perform this repair on all unsold vehicles before  retail delivery. Dealers should also use the VIN list to follow up with all owners to schedule appointments for this repair.

Recall VIN lists may contain confidential, restricted owner name and address information that was obtained from the Department of Motor Vehicles of various states. Use of this information is permitted for this recall only and is strictly prohibited from all other use. 

ADDITIONAL INFORMATION

If you have any questions or need assistance in completing this action, please contact your Service and Parts District Manager.

Customer Services/Field Operations

FCA US LLC

IMPORTANT SAFETY RECALL - OCCUPANT RESTRAINT CONTROL MODULE

This notice applies to your vehicle, 

[Model Year and Model]

VIN XXXXXXXXXXXXXXXXX 

T25/NHTSA 17V-302 

Dear [Name],

This notice is sent to you in accordance with the National Traffic and Motor Vehicle Safety Act.

FCA has decided that a defect, which relates to motor vehicle safety, exists in certain [2013-2016 (DS) RAM 1500 Pickup, 2013-2016 (DJ) RAM 2500 Pickup and 2014-2016 (D2) RAM 3500 Pickup] vehicles.

WHY DOES MY VEHICLE NEED REPAIRS? 

The Occupant Restraint Control (ORC) module on your truck [1] may activate a diagnostic trouble code (DTC) due to external stimulus which disables its ability to sense vehicle rollover events. When the DTC is set, airbag and seat belt pretensioner deployment based on rollover sensing is disabled for the ignition cycle in which the DTC was set. The loss of rollover-activated side air bags and seat belt pretensioner deployment capability during a crash may increase the risk of injury or death  .

HOW DO I RESOLVE THIS IMPORTANT SAFETY ISSUE? 

FCA will repair your vehicle [2] free of charge (parts and labor). To do this, your dealer will reprogram the ORC module with new software. In addition, your dealer will require your vehicle for proper check-in, preparation, and check-out during your visit. Your time is important to us; please be aware that these steps may require more time. The estimated repair time is one hour. We recommend that you schedule a service appointment to minimize your inconvenience. Please bring this letter with you to your dealership.

TO SCHEDULE YOUR FREE REPAIR CALL 1-800-853-1403 OR YOUR CHRYSLER, DODGE, JEEP OR RAM DEALER TODAY 

WHAT IF I ALREADY PAID TO HAVE THIS REPAIR COMPLETED? 

If you have already experienced this specific condition and have paid to have it repaired, you may visit www.fcarecallreimbursement.com  to submit your reimbursement request online. [3] Once we receive and verify the required documents, reimbursement will be sent to you within 60 days. If you have had previous repairs performed and/or already received reimbursement, you may still need to have the recall repair performed.

We apologize for any inconvenience, but are sincerely concerned about your safety. Thank you for your attention to this important matter.

Customer Assistance/Field Operations

Fiat Chrysler Automobiles US LLC

LOGO 

YOUR SCHEDULING OPTIONS 

VEHICLE PICTURE 

  1. RECOMMENDED OPTION Call your authorized Chrysler/Dodge/Jeep®/RAM/Dealership 
  2. Call the FCA Recall Assistance Center at 1-800-853-1403. An agent can confirm part availability and help schedule an appointment 
  3. Visit our Recall Website, recalls.mopar.com or scan below. 

    QR Code 

    You can find your nearest dealer and review all your scheduling options from this website. You will be asked to provide your Vehicle Identification Number (VIN) to protect and verify your identity. The last eight characters of your VIN are provided above.

DEALERSHIP INSTRUCTIONS 

Please reference Safety Recall T25.