LEMON Manuals: Even more car manuals for everyone
Home >> Dodge and Ram >> 2013 >> 2500 HD Power Wagon >> Repair and Diagnosis >> General Information >> Specifications Index >> Common Specs & Procedures >> Common Specs & Procedures

Common Specs & Procedures

RAM 2500 HD & 3500 HD COMMON SPECS & PROCEDURES

System Specification/Procedure
Air Conditioning
  Service A/C SYSTEM
  Torque FASTENER TORQUE
Axle Nut/Hub Nut
  Front 263 ft. lbs. (356 N.m)
  Rear N/A
Battery SPECIFICATIONS
Brakes
  Bleeding Sequence Base Brakes: STANDARD PROCEDURE , Antilock Brakes: STANDARD PROCEDURE - ABS BRAKE BLEEDING
  Disc Brakes
    Service Specifications BASE BRAKE
    Torque Base Brakes: TORQUE , Antilock Brakes: SPECIFICATIONS
  Drum Brakes
    Service Specifications N/A
    Torque N/A
Charging
  Generator GENERATOR RATINGS
  Torque TORQUE - GENERATOR/CHARGING SYSTEM
Drive Belts
  Adjustment Serpentine belt used, not adjustable.
  Drive Belt Routing Refer to appropriate "Belt Routing" figure under REMOVAL .
Engine Cooling
  General Service Specifications FILL VOLUMES
  Radiator Cap Pressure Diesel: 145 kPa (21 psi); Gas: 97 kPa (14 psi)
  Thermostat R & I THERMOSTAT
  Water Pump R & I PUMP, WATER
Engine Mechanical
  5.7L
    Compression Compression should not be less than 689 kPa (100 psi) and not vary more than 25 percent from cylinder to cylinder.
    Oil Pressure At Curb Idle Speed (MIN): 4 psi (25 kPa), @ 3000 RPM: 25-110 psi (170-758 kPa), If pressure is zero at curb idle, DO NOT run engine at 3000 RPM.
    Overhaul SPECIFICATIONS
    Torque TORQUE
  5.7L CNG
    Compression Compression should not be less than 689 kPa (100 psi) and not vary more than 25 percent from cylinder to cylinder.
    Oil pressure At Curb Idle Speed (MIN): 4 psi (25 kPa), @ 3000 RPM: 25-110 psi (170-758 kPa), If pressure is zero at curb idle, DO NOT run engine at 3000 RPM.
    Overhaul SPECIFICATIONS
    Torque TORQUE
  6.7L
    Compression The minimum cylinder pressure is 350 psi. Cylinder pressure should be within 20% from cylinder to cylinder.
    Oil pressure At Curb Idle Speed (MIN): 4 psi (25 kPa), @ 3000 RPM: 25-110 psi (170-758 kPa), If pressure is zero at curb idle, DO NOT run engine.
    Overhaul SPECIFICATIONS
    Torque TORQUE
Fluid Specifications See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button.
Flywheel/Flex Plate/Drive Plate Torque
  5.7L
    Flexplate 70 ft. lbs. (95 N.m)
    Flywheel 55 ft. lbs. (75 N.m)
  5.7L CNG 100 ft. lbs. (137 N.m)
  6.7L 100 ft. lbs. (137 N.m)
Fuel System
  Pressure Specification Diesel: 26, 107 psi (1800 bar); Gas: Non SRT-4  : 59 psi +/- 5 psi; SRT-4  : 80 psi +/- 5 psi (552 kPa +/- 34 kPa)
  Fuel Pressure Test Procedure Diesel: CHECKING THE FUEL DELIVERY SYSTEM ; Gas: CHECKING THE FUEL DELIVERY SYSTEM (HARD START)
  Fuel Filter Location Fuel filter is part of fuel pump module.
  Fuel Filter R & I CNG: MODULE, FUEL PUMP ; Diesel: MODULE, FUEL PUMP ; CNG: MODULE, FUEL PUMP ; Gas
Ignition
  Firing Order & Cylinder Identification FIRING ORDER & CYLINDER IDENTIFICATION
  Ignition Wires (Resistance) Coil On Plug
  Ignition Wires (Routing) Coil On Plug
Spark Plug
  5.7L
    Type LZFR5C-11G
    Gap .043 in. (1.1 mm)
    Torque 13 (± 2) ft. lbs. (18 (± 3) N.m): Torque critical tapered design. Do not exceed 15 ft. lbs.
Starting
  Starter STARTING SYSTEM
  Torque TORQUE
Wheel Alignment
  Adjustment Specifications SPECIFICATIONS
  Torque Front link and coil suspension: SPECIFICATIONS
Wheel & Tire
  Wheel Lug Nut Torque (SRW) Refer to SPECIFICATIONS