Diagnostic Test
- ASD RELAY OPERATION
- Ignition on, engine not running.
- With the scan tool, select View DTCs.
Is the DTC Active at this time?
Yes
- Go To 2.
No
- Perform the INTERMITTENT CONDITION diagnostic procedure. Refer to INTERMITTENT CONDITION .
- (A209) FUSED B+ CIRCUITS
- Turn the ignition off.
- Remove the ASD Relay from the TIPM. Refer to RELAY, AUTO SHUT DOWN, REMOVAL .
- Using a 12-volt test light connected to ground, probe the (A209) Fused B+ circuits in the TIPM.NOTE:
The test light should be illuminated and bright. Compare the brightness to that of a direct connection to the battery.
Does the test light illuminate brightly?
Yes
- Go To 3.
No
- Repair the open or short to ground in the (A209) Fused B+ circuits. Inspect and replace any open fuses. Refer to FUSE LOCATIONS AND TYPES, SPECIFICATIONS .
- Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
- ASD RELAY
- Measure the resistance of the ASD Relay Coil.
Is the resistance between 60 to 80 Ohms?
Yes
- Go To 4.
No
- Replace the ASD Relay. Refer to RELAY, AUTO SHUT DOWN, REMOVAL .
- Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
- Measure the resistance of the ASD Relay Coil.
- (K51) ASD RELAY CONTROL CIRCUIT OPEN
- Disconnect the C3 PCM harness connector.CAUTION:
Do not probe the PCM harness connectors. Probing the PCM harness connectors will damage the PCM terminals resulting in poor terminal to pin connection. Install the PCM Pinout Box (special tool #8815A, Kit, NGC, 38 Position) to perform diagnosis.
- Measure the resistance of the (K51) ASD Relay Control circuit from the TIPM to the appropriate terminals of PCM Pinout Box (special tool #8815A, Kit, NGC, 38 Position).
Is the resistance below 5.0 Ohms?
Yes
- Go To 5.
No
- Repair the open in the (K51) ASD Relay Control circuit.
- Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
- Disconnect the C3 PCM harness connector.
- (K51) ASD RELAY CONTROL CIRCUIT SHORTED TO GROUND
- Measure the resistance between ground and the (K51) ASD Relay Control circuit in the TIPM.
Is the resistance below 100 Ohms?
Yes
- Repair the short to ground in the (K51) ASD Relay Control circuit.
- Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
No
- Go To 6.
- Measure the resistance between ground and the (K51) ASD Relay Control circuit in the TIPM.
- POWERTRAIN CONTROL MODULE (PCM)
- Using the wiring diagram/schematic as a guide, inspect the wiring and connectors between the ASD Relay and the Powertrain Control Module (PCM).
- Look for any chafed, pierced, pinched or partially broken wires.
- Look for broken, bent, pushed out or corroded terminals. Verify that there is good pin to terminal contact in the ASD Relay and Powertrain Control Module connectors.
- Perform any Technical Service Bulletins that may apply.
Were there any problems found?
Yes
- Repair as necessary.
- Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
No
- Replace and program the Powertrain Control Module in accordance with the Service Information. Refer to MODULE, POWERTRAIN CONTROL, REMOVAL , and PCM/ECM REPROGRAMMING - GAS and follow the PCM/ECM PROGRAMMING procedure.
- Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .