DTC P0172: 1/1 O2 Sensor Fuel System Rich Or DTC P0175: 2/1 O2 Sensor Fuel System Rich: Testing
- Check for contaminants that may have damaged the O2 Sensor such as contaminated fuel, unapproved silicone, oil and coolant. Turn ignition on, engine not running. Using the DRBIII®, read DTCs. If any O2 Sensor, TP Sensor, ECT, MAP, or EVAP DTCs exist, those DTCs must be repaired before continuing. See DIAGNOSTIC TROUBLE CODE DEFINITIONS . Is the Good Trip Counter displayed and equal to zero? If yes, go to next step. If no, go to step 15.
- Release fuel system pressure. Install a fuel pressure gauge to the fuel rail. Turn ignition on, engine not running. Using the DRBIII®, actuate the Auto Shutdown (ASD) Fuel System Test and observe the fuel pressure gauge. Fuel pressure specification is 44.2-54.2 psi (305-373 kPa). Turn the ignition off. If fuel pressure is within specification, go to next step. If fuel pressure is greater than specification, replace the Fuel Pressure Regulator and Fuel Filter.
- Turn ignition on, engine not running. Using the DRBIII®, read the O2 Sensor voltage. Is the O2 Sensor voltage greater than 4.5 volts? If yes, go to next step. If no, go to step 11.
- Turn the ignition off. Wait a minimum of 10 minutes to allow the O2 Sensor to cool down before continuing the test. Allow the O2 Sensor voltage to stabilize between 4 and 5 volts. Turn ignition on, engine not running. Using the DRBIII®, actuate the O2 Heater Test. Using the DRBIII®, monitor O2 Sensor voltage for at least 2 minutes. Does the voltage stay greater than 4.5 volts? If yes, replace the O2 Sensor. If no, go to next step.
- The engine must be at operating temperature and in closed loop to perform this test. Start the engine. Allow the engine to reach normal operating temperature. Using the DRBIII®, select SYSTEM TESTS. Perform the PURGE VAPORS TEST. Observe the SHORT TERM ADAPTIVE value and press "3" to flow. Did the Short Term Adaptive value change? If yes, go to next step. If no, check evaporative emission system. See EMISSION SYSTEMS & SUB-SYSTEMS in appropriate SYSTEM & COMPONENT TESTING article.
- Turn ignition off. Turn ignition on, engine not running. Using the DRBIII®, read TP Sensor voltage. The throttle must be against the stop. Is the TP Sensor voltage 0.92 volt or less with the throttle closed? If yes, go to next step. If no, check for a binding throttle condition. If okay, replace the TP Sensor.
- Using the DRBIII®, continue to monitor the TP Sensor voltage. While monitoring the DRBIII®, slowly open and close the throttle. Does the voltage increase and decrease smoothly? If yes, go to next step. If no, replace the TP Sensor.
- Turn the ignition off. Connect a vacuum gauge to a manifold vacuum source. Start the engine. Allow the engine to idle. If engine will not idle, maintain a constant RPM above idle. Using the DRBIII® in SENSORS, read the MAP Sensor vacuum value. Is the DRBIII® reading within 1 in. Hg of the vacuum gauge reading? If yes, go to next step. If no, replace the MAP Sensor.
- Turn ignition off. Turn ignition on, engine not running. Using the DRBIII®, read the Engine Coolant Temperature (ECT) Sensor value. If the engine was allowed to sit overnight (cold soak), the temperature value should be a sensible value that is somewhere close to the ambient temperature. If engine coolant temperature is greater than 180°F (82°C), allow the engine to cool until 150°F (65°C) is reached. Start the engine. During engine warm-up, monitor the Engine Coolant Temperature Sensor value. The ECT temperature value change should be a smooth transition from start up to normal operating temperature 180°F (82°C). The value should reach at least 180°F (82°C). Did the Engine Coolant Temperature value increase smoothly and reach at least 180°F (82°C)? If yes, go to next step. If no, replace the ECT Sensor.
- Check for any of the following conditions/mechanical problems:
- Air induction system must be free from restrictions.
- Engine vacuum must be at least 13 in. Hg in Neutral.
- Engine valve timing must be within specifications.
- Engine compression must be within specifications.
- Engine exhaust system must be free of any restrictions or leaks.
- Positive Crankcase Ventilation (PCV) system must flow freely.
- Torque converter stall speed must be within specifications.
- Power brake booster must be free of internal vacuum leaks.
- Fuel must be free of contamination.
- Fuel Injectors must not be plugged or restricted and Fuel Injector/control wires must not be connected to an incorrect Fuel Injector.
- Turn ignition off. Disconnect the O2 Sensor harness connector. Turn ignition on, engine not running. Using the DRBIII®, monitor the O2 Sensor voltage. Is the O2 Sensor voltage greater than 4.5 volts? If yes, replace the O2 Sensor. If no, go to next step.
- Turn the ignition off. Disconnect the PCM harness connectors. Measure the resistance of the O2 Sensor Signal circuit from the PCM harness connector to the O2 Sensor harness connector. Is the resistance less than 5.0 ohms? If yes, go to next step. If no, repair the open in the O2 Sensor Signal circuit.
- Reconnect PCM harness connectors. Start the engine. Measure the voltage on the O2 Sensor Signal circuit at the O2 Sensor harness connector. Is the voltage greater than 5.3 volts? If yes, repair the short to voltage in the O2 Sensor Signal circuit. If no, go to next step.
- There are no possible causes remaining, replace and program the Powertrain Control Module.
- Check for contaminants that may have damaged the O2 Sensor such as contaminated fuel, unapproved silicone, oil and coolant. The conditions that set the DTC are not present at this time. With the engine running at normal operating temperature, monitor the DRBIII® parameters related to the DTC while wiggling the wiring harness. Look for parameter values to change and/or a DTC to set. Review the DRBIII® Freeze Frame information. If possible, try to duplicate the conditions under which the DTC was set. Refer to any Technical Service Bulletins (TSB) that may apply. Visually inspect the related wiring harness. Look for any chafed, pierced, pinched, or partially broken wires. Visually inspect the related wiring harness connectors. Look for broken, bent, pushed out, or corroded terminals. Were any of the above conditions present? If yes, repair as necessary. If no, test is complete.
WARNING:
The fuel system is under a constant pressure (even with the engine off). Before testing or servicing any fuel system hose, fitting or line, the fuel system pressure must be released. See FUEL SYSTEM PRESSURE RELEASE .
WARNING:
When the engine is operating, do not stand in a direct line with the fan. Do not put your hands near the pulleys, belts or fan. Do not wear loose clothing.
NOTE:
For this test to be valid, the thermostat must be operating correctly. This test works best if performed on a cold engine (cold soak).
WARNING:
When the engine is operating, do not stand in a direct line with the fan. Do not put your hands near the pulleys, belts or fan. Do not wear loose clothing.
WARNING:
When the engine is operating, do not stand in a direct line with the fan. Do not put your hands near the pulleys, belts or fan. Do not wear loose clothing.