LEMON Manuals: Even more car manuals for everyone
Home >> Chrysler >> 2005 >> PT Cruiser Base, 2D Convertible, Automatic >> Repair and Diagnosis >> Steering >> Steering Column >> Steering System >> Pump >> Pump >> Removal >> Removal - 2.0L/2.4L Engine

Removal - 2.0L/2.4L Engine

NOTE: Before proceeding, (Refer to STEERING - WARNING) .
  1. Siphon as much fluid as possible from the power steering fluid reservoir.
  2. Raise the vehicle. (Refer to LUBRICATION & MAINTENANCE/HOISTING - STANDARD PROCEDURE)
  3. Remove the right front tire and wheel assembly.
  4. Remove the screws fastening the front fascia to the reinforcement as necessary in order to access the drive-belt splash shield forward fastener screw. See Fig 1.
    Fig 1: Fascia And Splash Shield Fasteners
    GC0021694Courtesy of DAIMLERCHRYSLER CORP.
    1 - FASCIA FASTENERS
    2 - FASCIA FASTENERS
    3 - SPLASH SHIELD FASTENERS
  5. Remove the drive-belt splash shield fasteners. See Fig 1. Remove the shield.
  6. Remove the accessory drive-belt from the A/C compressor and power steering pump. Refer to COOLING for the procedure.
  7. Remove the electrical connectors from the A/C compressor. See Fig 2.
    Fig 2: A/C Compressor Mounting
    GC0021702Courtesy of DAIMLERCHRYSLER CORP.
    1 - COMPRESSOR
  8. Remove the four bolts fastening the A/C compressor to the engine, then move the compressor toward the center of the vehicle, allowing the compressor to settle in place. See Fig 2.
  9. Remove the pressure hose from the pump in the following fashion. See Fig 3 and Fig 4.
    1. Place a crowfoot wrench on a long extension onto the pressure hose tube nut at the pump.
    2. Place a shop towel between the crowfoot and the pump pulley to avoid slipping and possibly damaging the pulley.
    3. Unthread the tube nut from the pump.
    Fig 3: Pressure Hose Connection To Pump
    GC0021703Courtesy of DAIMLERCHRYSLER CORP.
    1 - PUMP
    2 - PRESSURE HOSE
    Fig 4: Pressure Hose Tube Nut
    GC0021704Courtesy of DAIMLERCHRYSLER CORP.
    1 - PUMP PULLEY
    2 - POWER STEERING PUMP
    3 - PRESSURE HOSE TUBE NUT
  10. Lower the vehicle.
  11. Remove the grille from the front of the vehicle. See Fig 5.
    Fig 5: Grille Attachment
    GC0021705Courtesy of DAIMLERCHRYSLER CORP.
    1 - GRILLE
    2 - RETAINER
  12. Remove the hood-opening weatherstrip from across the radiator closure panel.
  13. Remove the ambient temperature sensor from the radiator closure panel. See Fig 6.
    Fig 6: Ambient Temperature Sensor
    GC0021706Courtesy of DAIMLERCHRYSLER CORP.
    1 - FASTENER
    2 - SENSOR
  14. Remove the fasteners securing the upper radiator closure panel in place, then remove the panel. See Fig 7.
    Fig 7: Radiator Closure Panel
    GC0021707Courtesy of DAIMLERCHRYSLER CORP.
    1 - FASTENERS
  15. Lift the cooling module out of its lower mounts and carefully move it toward the left side of the vehicle. It will move only a limited amount with the hoses still connected. Do not force it.
    NOTE: For additional room, the right side bolts securing the lower radiator closure panel in front of the cooling module can be removed.
  16. Using a bungee cord, tie the cooling module forward as shown. See Fig 8. Be sure to attach the cord in a location that will not damage the vehicle. Do not overtighten the bungee cord. It just needs to hold the module forward.
    Fig 8: Cooling Module Tied Forward
    GC0021708Courtesy of DAIMLERCHRYSLER CORP.
    1 - COOLING MODULE
  17. Remove the clamp securing the supply hose to the power steering pump supply fitting, then remove the hose from the supply fitting. See Fig 9.
    Fig 9: Supply Hose At Pump
    GC0021709Courtesy of DAIMLERCHRYSLER CORP.
    1 - SUPPLY HOSE CLAMP
    2 - POWER STEERING PUMP
  18. Remove the three bolts securing the pump in place. See Fig 10.
    Fig 10: Mounting Bolts
    GC0021710Courtesy of DAIMLERCHRYSLER CORP.
    1 - POWER STEERING PUMP
    2 - SUPPORT
  19. Remove the 2 bolts securing the stamped steel support bracket to the engine block. See Fig 10. Remove the bracket.
  20. Ease the cooling module forward, don't force it, and remove the power steering pump and pulley where shown. See Fig 11.
Fig 11: Power Steering Pump Removal
GC0021711Courtesy of DAIMLERCHRYSLER CORP.