LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2021 >> Traverse LS, FWD >> Repair and Diagnosis >> Quick Lookups >> Technical Bulletins >> Technical Service Bulletins >> Other Variant >> Collision/Avoidance >> Changing Front Pedestrian Braking Alert Options Error (PIT5957)

Changing Front Pedestrian Braking Alert Options Error (PIT5957)

WARNING: This page is about the Traverse High Country, 4WD, which is a different variant/trim than selected.
Publication date: 2023-04-26
Reference number: PIT5957
Supersedes refnos: 23-NA-078

CHANGING FRONT PEDESTRIAN BRAKING ALERT OPTIONS ERROR

CHANGING FRONT PEDESTRIAN BRAKING ALERT OPTIONS ERROR

TECHNICAL SERVICE BULLETIN

Reference Number(s): 23-NA-078, Date of Issue:  Apr 26, 2023
Supercedes: This Bulletin Replaces PIT5957. Please Discard all Copies of PIT5957.

SERVICE INFORMATION

Brand: Model: Model Year: VIN: Engine: Transmission:
from to from to
Chevrolet Traverse 2021 2023        
Involved Region or Country  United States, Canada
Additional Options (RPOs)  Equipped with RPO UGN Radar Based Sensing
Condition  Some customers may comment on not allowing the driver to change the option from Alert/Braking to only alert or off. Pedestrian Braking feature is not affected, only the option for changing the alerts.
Cause  The cause of the condition may be software anomalies.
Correction  Verify the option is not available then reprogram the Active Safety Control Module.
GM6182077Courtesy of GENERAL MOTORS COMPANY

SERVICE PROCEDURE

IMPORTANT:

Service agents must comply with all International, Federal, State, Provincial, and/or Local laws applicable to the activities it performs under this bulletin, including but not limited to handling, deploying, preparing, classifying, packaging, marking, labeling, and shipping dangerous goods. In the event of a conflict between the procedures set forth in this bulletin and the laws that apply to your dealership, you must follow those applicable laws. 

CAUTION:

Before downloading the update files, be sure the computer is connected to the internet through a network cable (hardwired). DO NOT DOWNLOAD or install the files wirelessly. If there is an interruption during programming, programming failure or control module damage may occur.

IMPORTANT:

The service technician always needs to verify that the VIN displayed in the TLC left side drop down menu and the top center window match the VIN plate of the vehicle to be programmed prior to using Service Programming System 2 (SPS2) for programming or reprogramming a module.

CAUTION:

Be sure the VIN selected in the drop down menu (1) is the same as the vehicle connected (2) before beginning programming.

GM5743643Courtesy of GENERAL MOTORS COMPANY
IMPORTANT:

If the vehicle VIN DOES NOT match, the message below will be shown

GM5877000Courtesy of GENERAL MOTORS COMPANY
GM5644477Courtesy of GENERAL MOTORS COMPANY
IMPORTANT:

Techline Connect screens shown above.

IMPORTANT:

If the same calibration/software warning is noted on the TLC Summary screen, select OK and follow screen instructions. After a successful programming event, the WCC is located in the Service Programming System dialogue box of the SPS Summary screen. No further action is required. Refer to the Warranty section of the bulletin.

  1. Reprogram the Active Safety Control Module.
    GM5644478Courtesy of GENERAL MOTORS COMPANY
    NOTE:

    The screenshot above is an example of module programming and may not be indicative of the specific module that is being programmed. Module selection and VIN information have been blacked out.

    IMPORTANT:

    To avoid warranty transaction rejections, you MUST record the warranty claim code provided on the Warranty Claim Code (WCC) screen shown above on the job card. Refer to callout 1 above for the location of the WCC on the screen.

  2. Record SPS Warranty Claim Code on job card for warranty transaction submission.

WARRANTY INFORMATION

For vehicles repaired under warranty, use:

Labor Operation Description Labor Time
*2810435 Active Safety Control Module Reprogramming with SPS Use Published Labor Operation Time
IMPORTANT:

*To avoid warranty transaction rejections, carefully read and follow the instructions below:

  • The Warranty Claim Code must be accurately entered in the "Warranty Claim Code" field of the transaction.
  • When more than one Warranty Claim Code is generated for a programming event, it is required to document all Warranty Claim Codes in the "Correction" field on the job card. Dealers must also enter one of the codes in the "Warranty Claim Code" field of the transaction, otherwise the transaction will reject. It is best practice to enter the FINAL code provided by SPS2.

Warranty Claim Code Information Retrieval 

GM6125774Courtesy of GENERAL MOTORS COMPANY

If the Warranty Claim Code was not recorded on the Job Card, the code can be retrieved in the SPS2 system as follows:

  1. Open TLC on the computer used to program the vehicle.
  2. Select and start SPS2.
  3. Select Settings (1).
  4. Select the Warranty Claim Code tab (2).

The VIN, Warranty Claim Code and Date/Time will be listed on a roster of recent programming events. If the code is retrievable, dealers should resubmit the transaction making sure to include the code in the SPS Warranty Claim Code field.

SERVICE INFORMATION

Version  1
Modified  Released April 25, 2023