LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2021 >> Tahoe SSV >> Repair and Diagnosis >> Collision >> Body Panels >> Body Panel Replacement >> Body Panel Replacement >> Body Side Outer Panel Sectioning (SWB) >> Installation Procedure

Installation Procedure

GM5437908Courtesy of GENERAL MOTORS COMPANY
  1. Select overlap or backing plate for the section joint (1). Overlap/Backing Plate Sectioning 
    GM5355062Courtesy of GENERAL MOTORS COMPANY
  2. NOTE:

    Prepare body side outer panel section before installation.

  3. Prepare body side outer panel section (1) per installation requirements.
  4. Prepare all joining surfaces for welding as necessary.
  5. Apply weld-thru coating or equivalent to all welding surfaces. Anti-Corrosion Treatment and Repair
    GM5354999Courtesy of GENERAL MOTORS COMPANY
  6. Clean and prepare body side outer panel and vehicle for adhesive according to adhesive manufacturer's recommendations. METAL PANEL BONDING
  7. Apply structural adhesive (1) on the mating surfaces on the body side outer panel and vehicle according to adhesive manufacturer's recommendations. METAL PANEL BONDING
    GM5354786Courtesy of GENERAL MOTORS COMPANY
  8. NOTE:

    Not all spot welds noted during removal process are required to be reinstalled. Per individual procedure structural adhesive can be used in place of spot welds. METAL PANEL BONDING

  9. Apply structural adhesive (1) on the mating surfaces on the body side outer panel and vehicle according to adhesive manufacturer's recommendations. METAL PANEL BONDING
    GM5354391Courtesy of GENERAL MOTORS COMPANY
  10. NOTE:

    Not all spot welds noted during removal process are required to be reinstalled. Per individual procedure structural adhesive can be used in place of spot welds. METAL PANEL BONDING

  11. Apply structural adhesive (1) on the mating surfaces on the body side outer panel and vehicle according to adhesive manufacturer's recommendations. METAL PANEL BONDING
    GM5344484Courtesy of GENERAL MOTORS COMPANY
  12. NOTE:

    Not all spot welds noted during removal process are required to be reinstalled. Per individual procedure structural adhesive can be used in place of spot welds. METAL PANEL BONDING

  13. Apply structural adhesive (1) on the mating surfaces on the body side outer panel and vehicle according to adhesive manufacturer's recommendations. METAL PANEL BONDING
    GM5344442Courtesy of GENERAL MOTORS COMPANY
  14. NOTE:

    Not all spot welds noted during removal process are required to be reinstalled. Per individual procedure structural adhesive can be used in place of spot welds. METAL PANEL BONDING

  15. Apply structural adhesive (1) on the mating surfaces on the body side outer panel and vehicle according to adhesive manufacturer's recommendations. METAL PANEL BONDING
    GM5344485Courtesy of GENERAL MOTORS COMPANY
  16. NOTE:

    Not all spot welds noted during removal process are required to be reinstalled. Per individual procedure structural adhesive can be used in place of spot welds. METAL PANEL BONDING

  17. Apply structural adhesive (1) on the mating surfaces on the body side outer panel and vehicle according to adhesive manufacturer's recommendations. METAL PANEL BONDING
    GM5348282Courtesy of GENERAL MOTORS COMPANY
  18. NOTE:

    Not all spot welds noted during removal process are required to be reinstalled. Per individual procedure structural adhesive can be used in place of spot welds. METAL PANEL BONDING

  19. Apply structural adhesive (1) on the mating surfaces on the body side outer panel and vehicle according to adhesive manufacturer's recommendations. METAL PANEL BONDING
    GM5337754Courtesy of GENERAL MOTORS COMPANY
  20. NOTE:

    Left side only.

  21. Apply sealer (1) on vehicle.
    GM5355062Courtesy of GENERAL MOTORS COMPANY
  22. Install body side outer panel (1) on vehicle and clamp into place.
    GM5385359Courtesy of GENERAL MOTORS COMPANY
  23. Re-hem the wheel opening flange area (1) of the body side outer panel.
    GM5346448Courtesy of GENERAL MOTORS COMPANY
  24. NOTE:

    Spot welds and MIG/MAG welds with 3 or 4 metals stacked up can be completed simultaneously when all panels or components are present.

    NOTE:

    Use text for actual weld count.

  25. Install spot welds (1). [69x]
    GM5355147Courtesy of GENERAL MOTORS COMPANY
  26. NOTE:

    Spot welds are required when securing the body side outer panel and lock plate striker to the vehicle.

  27. Install spot welds (1). [2x]
    GM5438015Courtesy of GENERAL MOTORS COMPANY
  28. Install MIG/MAG welds at the sectioned joint. Overlap/Backing Plate Sectioning 
  29. Install roof panel. (IF APPLICABLE FOR SECTIONING LOCATION) Roof Outer Panel Replacement (SWB) Roof Outer Panel Replacement (LWB Sunroof) Roof Outer Panel Replacement (LWB) Roof Outer Panel Replacement (SWB Sunroof) 
  30. Apply the sealers and anti-corrosion materials to the repair area as necessary. Anti-Corrosion Treatment and Repair
  31. NOTE:

    Before refinishing, refer to Anti-Corrosion Treatment and Repair

  32. Paint the repaired area. Basecoat/Clearcoat Paint Systems
  33. Install all related panels and components.
  34. Connect the battery negative cable. Battery Negative Cable Disconnection and Connection (9C1, 5W4)Battery Negative Cable Disconnection and Connection (KL9)
  35. Enable the SIR System. SIR Disabling and Enabling