LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2016 >> Spark LS, Standard Trans >> Repair and Diagnosis >> Body & Frame >> Windows >> Fixed And MOVEABLE Window System >> Diagnostic Information and Procedures >> Rear Window Defogger Malfunction (With C41) >> Circuit/System Testing

Circuit/System Testing

Rear Window Defogger Grid Malfunction

  1. Ignition OFF and all vehicle systems OFF, disconnect the KR5 Rear Defogger Relay. It may take up to 2 minutes for all vehicle systems to power down.
  2. Test for less than 10 Ω between the ground circuit terminal 85 and ground.
    • If 10 Ω or greater 
    1. Ignition OFF.
    2. Test for less than 2 Ω in the ground circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, repair the open/high resistance in the ground connection.
    • If less than 10 Ω 
  3. Ignition ON.
  4. Verify a test lamp illuminates between the B+ circuit terminal 30 and ground.
    • If the test lamp does not illuminate 
    1. Ignition OFF.
    2. Test for less than 2 Ω in the B+ circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
    • If the test lamp illuminates 
  5. Connect a test lamp between the control circuit terminal 86 and the ground circuit terminal 85. Engine running
  6. Verify the test lamp turns ON and OFF when commanding the E18 Rear Defogger Grid ON and OFF by pressing the rear window defogger switch.
    • If the test lamp is always OFF 
    1. Ignition OFF, disconnect the harness connector at the K9 Body Control Module.
    2. Test for infinite resistance between the control circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance
    3. Test for less than 2 Ω in the control circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K9 Body Control Module.
    • If the test lamp is always ON 
    1. Ignition OFF, disconnect the harness connector at the K9 Body Control Module, ignition ON.
    2. Test for less than 1 V between the control circuit and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V, replace the K9 Body Control Module.
    • If the test lamp turns ON and OFF 
  7. Verify that a test lamp does not illuminate between the control circuit terminal 30 and ground.
    • If the test lamp illuminates 

      Repair the short to voltage on the control circuit

    • If the test lamp does not illuminate 
  8. Ignition OFF and all vehicle systems OFF, disconnect the X2 harness connector at the E18 Rear Defogger Grid. It may take up to 2 minutes for all vehicle systems to power down.
  9. Test for less than 10 Ω between the ground circuit terminal 1 and ground.
    • If 10 Ω or greater 
    1. Ignition OFF.
    2. Test for less than 2 Ω in the ground circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, repair the open/high resistance in the ground connection.
    • If less than 10 Ω 
  10. Connect the X2 harness connector at the E18 Rear Defogger Grid.
  11. Ignition ON, connect a 20 A fused jumper wire between the B+ circuit terminal 87 and the control circuit terminal 30.
  12. Verify the E18 Rear Defogger Grid is activated.
    • If the E18 Rear Defogger Grid does not activate 
    1. Ignition OFF, disconnect the harness connector at the E18 Rear Defogger Grid.
    2. Test for infinite resistance between the control circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance
    3. Test for less than 2 Ω in the control circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the E18 Rear Defogger Grid.
    • If the E18 Rear Defogger Grid activates 
  13. Test or replace the KR5 Rear Defogger Relay.

Rear Window Defogger Indicator Malfunction

  1. Ignition OFF, disconnect the harness connector at the K33 HVAC Control Module. Ignition ON,
  2. Verify that a test lamp does not illuminate between the control circuit terminal 7 and ground.
    • If the test lamp illuminates 
    1. Ignition OFF, disconnect the harness connector at the K9 Body Control Module, ignition ON.
    2. Test for less than 1 V between the control circuit and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V, replace the K9 Body Control Module.
    • If the test lamp does not illuminate 
  3. Connect a test lamp between the control circuit terminal 7 and ground.
  4. Engine running, connect a 3 A fused jumper wire between the signal circuit terminal 3 and ground.
  5. Verify the test lamp illuminates
    • If the test lamp does not illuminate 
    1. Ignition OFF, disconnect the harness connector at the K9 Body Control Module.
    2. Test for infinite resistance between the control circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance
    3. Test for less than 2 Ω in the control circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K9 Body Control Module.
    • If the test lamp illuminates 
  6. Replace the K33 HVAC Control Module.

Rear Window Defogger System Inoperative

  1. Ignition OFF, disconnect the X1 harness connector at the K33 HVAC Control Module. Engine running.
  2. Verify the E18 Rear Defogger Grid is not active.
    • If the E18 Rear Defogger Grid is active 
    1. Ignition OFF, disconnect the X2 harness connector at the K9 Body Control Module.
    2. Test for infinite resistance between the K33 HVAC Control Module signal circuit terminal 3 X1 and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance, replace the K9 Body Control Module.
    • If E18 Rear Defogger Grid is not active 
  3. Install a 3 A fused jumper wire between the signal circuit terminal 3 and ground.
  4. Verify the E18 Rear Defogger Grid is active.
    • If not active 
    1. Ignition OFF, disconnect the harness connector at the K9 Body Control Module, ignition ON.
    2. Test for less than 1 V between the signal circuit and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V
    3. Test for less than 2 Ω in the signal circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K9 Body Control Module.
    • If Active 
  5. Replace the K33 HVAC Control Module.