LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2002 >> Corvette Base, 2D Convertible, Automatic >> Repair and Diagnosis >> Engine Mechanical >> Engine Exhaust System >> Repair Instructions >> Exhaust Manifold Replacement - Left >> Installation Procedure

Installation Procedure

Important:  Tighten the exhaust manifold bolts as specified in the service procedure. Improperly installed and/or leaking exhaust manifold gaskets may effect vehicle emissions and/or On-Board Diagnostics (OBD) II system performance.

The cylinder head exhaust manifold bolt hole threads must be cleaned and free of debris or threadlocking material.

CAUTION: Refer to FASTENER NOTICE .
  1. If necessary, install the exhaust manifold heat shield and bolts.

    Tighten 

    Tighten the exhaust manifold heat shield bolts to 9 N.m (80 lb in).

  2. Apply a 5 mm (0.2 in) wide band of threadlock GM P/N 12345493 (Canadian P/N 10953489), or equivalent to the threads of the exhaust manifold bolts.
    Fig 1: Installing Exhaust Manifold Bolts
    G01695586Courtesy of GENERAL MOTORS CORP.
  3. Position the exhaust manifold and a NEW gasket into place.
  4. Install the exhaust manifold bolts.

    Tighten 

    1. 4.1.  Tighten the exhaust manifold bolts a first pass to 15 N.m (11 lb ft). Tighten the exhaust manifold bolts beginning with the center two bolts. Alternate from side-to-side, working toward the outside bolts.
    2. 4.2.  Tighten the exhaust manifold bolts a final pass to 25 N.m (18 lb ft). Tighten the exhaust manifold bolts beginning with the center two bolts. Alternate from side-to-side, working toward the outside bolts.
  5. Bend over the exposed edge of the exhaust manifold gasket at the rear of the cylinder head.
  6. Install the spark plugs.
  7. Place the ignition coil bracket into place.
  8. Apply threadlock GM P/N 12345382 (Canadian P/N 10953489), or equivalent to the threads of the coil bracket studs.
  9. Install the ignition coil bracket studs.

    Tighten 

    Tighten the ignition coil bracket studs to 12 N.m (106 lb in).

    Fig 2: Installing Spark Plugs
    G01695587Courtesy of GENERAL MOTORS CORP.
  10. Install the brake booster vacuum hose to the brake booster.
    Fig 3: Installing Brake Booster Vacuum Hose
    G01695588Courtesy of GENERAL MOTORS CORP.
  11. Install the AIR pipe (with check valve) and a NEW gasket.
  12. Install the AIR pipe bolts.

    Tighten 

    Tighten the AIR pipe bolts to 20 N.m (15 lb ft).

    Fig 4: Installing AIR Pipe Bolts
    G01695589Courtesy of GENERAL MOTORS CORP.
  13. Install the AIR pipe (2).
  14. Install the AIR injection pipe hose (3) to the left check valve.
  15. Install the AIR injection pipe hose (1) to the right check valve.
  16. Install the hose clamps at the right and left check valves.
    Fig 5: Installing AIR Injection Pipe Hose
    G01695590Courtesy of GENERAL MOTORS CORP.
  17. Install the AIR hose to the AIR pipe.
  18. Install the hose clamp at the AIR pipe.
  19. Raise the vehicle.
    Fig 6: Installing AIR Pipe Hose Clamp
    G01695591Courtesy of GENERAL MOTORS CORP.
  20. Apply anti-seize compound GM P/N 12377953 or equivalent to the threads of the oxygen sensor.
    CAUTION: Refer to OXYGEN SENSOR NOTICE .
  21. Install the oxygen sensor.

    Tighten 

    Tighten the oxygen sensor to 42 Nm (30 lb ft).

  22. Install the oxygen sensor connector clip at the body.
  23. Connect the oxygen sensor electrical connector.
  24. Install the CPA lock.
    Fig 7: Installing Oxygen Sensor
    G01695592Courtesy of GENERAL MOTORS CORP.
  25. Install the exhaust manifold nuts.

    Tighten 

    Tighten the exhaust manifold nuts to 20 N.m (15 lb ft).

  26. Lower the vehicle.
  27. Install the generator. Refer to GENERATOR .
    Fig 8: Installing Exhaust Manifold Nuts
    G01695593Courtesy of GENERAL MOTORS CORP.
  28. Install the fuel rail cover.
    Fig 9: Installing Fuel Rail Cover
    G01695594Courtesy of GENERAL MOTORS CORP.