LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2001 >> Cavalier Base, 2D Coupe, Standard >> Repair and Diagnosis >> Engine Performance >> System >> Engine Controls Self-Diagnostics - 2.2L & 2.4L >> Self-Diagnostic System >> Powertrain Diagnostic System Check (CNG)

Powertrain Diagnostic System Check (CNG)

NOTE: Check for applicable Technical Service Bulletins (TSBs) before proceeding. DO NOT perform the following procedure if driveability conditions are not present. DO NOT turn ignition off during the following procedure or clear DTCs unless instructed to do so.
  1. Ensure both fuel tanks are at least 1/4 full. Turn ignition off. Connect scan tool to Data Link Connector (DLC). Turn ignition on. If Malfunction Indicator Light (MIL) is illuminated, go to next step. If MIL does not illuminate, go to MIL INOPERATIVE (CNG)  under SYSTEM TESTS.
  2. Using scan tool, attempt to establish communication with Powertrain Control Module (PCM). If scan tool communicates with PCM, go to next step. If scan tool does not communicate with PCM, see SCAN TOOL DOES NOT COMMUNICATE WITH CLASS 2 DEVICE in appropriate BODY CONTROL MODULES article. If scan tool does not power up, go to SCAN TOOL DOES NOT POWER UP in appropriate BODY CONTROL MODULES article in ACCESSORIES & EQUIPMENT.
  3. Using scan tool, attempt to communicate with Alternative Fuels Engine Control Unit (AF ECU). If scan tool displays alternative fuel data, go to next step. If scan tool does not display alternative fuel data, go to IGNITION RELAY DIAGNOSIS (2.2L - CAVALIER - CNG) under IGNITION SYSTEMS in SYSTEM & COMPONENT TESTING - CARS - EXCEPT METRO & PRIZM article.
  4. Select DTC display function for PCM and AF ECU. If DTCs are set, go to step  10 . If DTCs are not set, go to next step.
  5. Using scan tool, command MIL off. If MIL turns off, go to next step. If MIL does not turn off, go to MIL ON STEADY (CNG)  under SYSTEM TESTS.
  6. Crank engine for a maximum of 10 seconds. If engine starts, go to next step. If engine does not start, go to step  9 .
  7. Monitor Fuel Indicator Light (FIL) and select NGO ENABLE OUTPUT and INPUT parameters on scan tool to determine which fuel system is operating. If vehicle is operating on gasoline and FIL is not illuminated, go to fuel indicator light diagnosis in appropriate ANALOG INSTRUMENT PANELS article in ACCESSORIES & EQUIPMENT. If NGO ENABLE OUTPUT and INPUT parameters do not indicate same data, go to FUEL SYSTEM UNWANTED SWITCH TO GASOLINE under FUEL SYSTEMS (2.2L - CAVALIER CNG) in SYSTEM & COMPONENT TESTING - CARS - EXCEPT METRO & PRIZM article.
  8. Operate vehicle and observe/record engine data parameters on scan tool. If parameters are within operating range, go to step  11 . If parameters are not within operating range, go to DTC testing procedure that best matches out of range condition. See DIAGNOSTIC TROUBLE CODE DEFINITIONS  .
  9. Remove CNG fuse (20-amp) located in underhood fuse block. Crank engine for at least 10 seconds. If engine starts and runs with fuse removed, reinstall fuse and go to IGNITION RELAY DIAGNOSIS (2.2L - CAVALIER - CNG) under IGNITION SYSTEMS in SYSTEM & COMPONENT TESTING - CARS - EXCEPT METRO & PRIZM article. If engine does not start and run, go to POWERTRAIN DIAGNOSTIC SYSTEM CHECK (GASOLINE)  .
  10. Compare stored AF ECU DTCs with PCM DTCs. If DTCs are stored only in PCM, diagnose gasoline related DTCs. See DIAGNOSTIC TROUBLE CODE DEFINITIONS  . If same DTCs are stored in AF ECU and PCM or only in AF ECU, diagnose alternative fuel (CNG) related DTCs. If multiple DTCs are set in both AF ECU and PCM, diagnose gasoline related DTCs first.
  11. If driveability conditions exist, go to next step. If driveability conditions do not exist, go to step  13 .
  12. Perform FUEL SYSTEM DIAGNOSIS under FUEL SYSTEMS (2.2L - CAVALIER CNG) in SYSTEM & COMPONENT TESTING - CARS - EXCEPT METRO & PRIZM article. If fuel system diagnosis locates and repairs a malfunction, go to step  15 . If fuel system diagnosis does not locate and repair a malfunction, attempt to diagnose by symptom. See appropriate TROUBLE SHOOTING - NO CODES article.
  13. If symptoms exist for fuel gauge, fuel gauge selector or fuel indicator light, diagnose and repair as necessary. See SYSTEM TESTS in appropriate ANALOG INSTRUMENT PANELS article in ACCESSORIES & EQUIPMENT. If symptoms do not exist for fuel gauge, fuel gauge selector or fuel indicator light, go to next step.
  14. Ensure ignition is off. Remove CNG fuse (20-amp) from underhood fuse block. This will cause a forced switch to gasoline operation. Crank engine for at least 10 seconds. If engine starts and runs on gasoline, go to next step. If engine does not start and run on gasoline, go to FUEL PUMP RELAY DIAGNOSIS under FUEL SYSTEMS (2.2L - CAVALIER CNG) in SYSTEM & COMPONENT TESTING - CARS - EXCEPT METRO & PRIZM article.
  15. Remove all test equipment except scan tool. Reconnect any disconnected components. Using scan tool, clear DTCs from AF ECU and PCM. Turn ignition off and wait 30 seconds. Start engine and operate vehicle. Monitor FIL and MIL operation. Observe vehicle performance and driveability. After operating vehicle check for DTCs in AF ECU and PCM. If vehicle operates on CNG with normal driveability, no FIL/MIL illumination and no set DTCs, system is okay. If vehicle does not operate on CNG with normal driveability, or FIL/MIL are illuminated or DTCs are set, go to step  1 .