LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2001 >> Blazer 2D Utility, 4WD, Part Time, Standard >> Repair and Diagnosis >> Engine Performance >> System >> Engine Controls Self-Diagnostics - 4.3L >> Diagnostic Tests >> DTC P0106: Manifold Absolute Pressure System Performance >> Diagnostic Procedures

Diagnostic Procedures

  1. Perform powertrain diagnostic system check. See POWERTRAIN DIAGNOSTIC SYSTEM CHECK  under SELF-DIAGNOSTIC SYSTEM. After performing powertrain diagnostic system check, go to next step.
  2. Using scan tool, observe the throttle angle parameter. Move the throttle slowly from closed to wide open position. If throttle angle moves steadily and completely from zero to greater than 98 percent, go to next step. If throttle angle does not move steadily and completely from zero to greater than 98 percent, go to DTC P0121 .
  3. NOTE: In order to determine correct MAP sensor value of barometric pressure for any elevation, perform either of following:
  4. Compare MAP sensor value to BARO value in a known-good vehicle. Obtain the local weather service barometer reading (in. Hg). Multiply reading by 3.4. The result indicates the correct BARO value in kPa for your area. If MAP value normal for the altitude, go to next step. If MAP value is not normal for the altitude, go to step  8.
  5. Observe MAP sensor kPa display on scan tool. Start engine. If MAP sensor changes value, go to next step. If MAP sensor does not change value, go to step  8.
  6. Turn ignition off. Disconnect vacuum hose from MAP sensor. Leave harness connected. Connect a hand-held vacuum pump to MAP sensor. Turn ignition on, with engine off. Observe MAP sensor value as vacuum is slowly applied at one in. Hg at a time. Each inch of vacuum should result in a 3-4 kPa drop in MAP sensor value. Observe MAP sensor value or display for a skip or a jump while increasing vacuum up to 20 in. Hg. If scan tool indicates a skip or a jump in value, go to step  16. If scan tool does not indicate a skip or jump in value, go to next step.
  7. Observe MAP sensor value with 20 in. Hg applied to MAP sensor. If scan tool indicates that MAP sensor value is less than 34 kPa, go to next step. If scan tool does not indicate that MAP sensor value is less than 34 kPa, go to step  8.
  8. Disconnect hand-held vacuum pump. MAP sensor value should return to value observed in step  3. If MAP sensor value returns to original value observed in step  3, see DIAGNOSTIC AIDS . If MAP sensor value does not return to original value observed in step  3, go to step  16.
  9. Turn ignition off. Disconnect MAP sensor harness connector. Turn ignition on, with engine off. If scan tool indicates that MAP sensor voltage is greater than 0.1 volt, go to step  15. If scan tool does not indicate that MAP sensor voltage is not greater than 0.1 volt, go to next step.
  10. Connect a fused jumper wire between MAP sensor harness connector terminals "B" (Light Green wire) and "C" (Gray wire). See Figure. If scan tool indicates that MAP sensor voltage is about 5 volts, go to next step. If scan tool does not indicate that MAP sensor voltage is about 5 volts, go to step  14.
  11. Remove jumper wire. Check voltage between a known-good ground and MAP sensor harness connector terminal "C" (Gray wire). If voltage reading is greater than 5.2 volts, go to step  12. If voltage reading is not greater than 5.2 volts, go to next step.
  12. Using a test light connected to battery voltage, probe MAP sensor harness connector terminal "A" (Orange/Black wire on "L" and "M" Series; Orange wire on "S" and "T" Series). If test light illuminates, go to step  16. If test light does not illuminate, go to step  13.
  13. Turn ignition off. Check for short to voltage in Gray wire. Repair as necessary. After repairs, go to step  20. If circuit is okay, go to step  17.
  14. Turn ignition off. Check for high resistance or open in Orange/Black wire ("M" and "L" Series) or Orange wire ("S" and "T" Series). Repair as necessary. After repairs, go to step  20. If circuit is okay, go to step  17.
  15. Turn ignition off. Check for high resistance in Gray wire or Light Green wire. Repair as necessary. After repairs, go to step  20. If circuit(s) are okay, go to step  17.
  16. Turn ignition off. Check for short to voltage in Light Green wire. Repair as necessary. After repairs, go to step  20. If circuit is okay, go to step  17.
  17. Turn ignition off. Check MAP sensor for poor connections. Repair as necessary. After repairs, go to step  20. If connections are okay, go to step  18.
  18. Check PCM for poor connections. Repair as necessary. After repairs, go to step  20. If connections are okay, go to step  19.
  19. Replace MAP sensor. After replacing sensor, go to step  20.
  20. Replace PCM. Perform PCM relearn procedure. See POWERTRAIN CONTROL MODULE  under PROGRAMMING. After replacing PCM, go to next step.
  21. Using scan tool, clear DTCs. Turn ignition off for 30 seconds. Start and operate vehicle within the conditions for running the DTC. See CODE ENABLE CRITERIA . If DTC runs and passes, go to next step. If DTC resets, go to step  2.
  22. Using scan tool, observe the stored information and Capture Info. If scan tool displays any undiagnosed DTCs, diagnose affected DTCs. See DIAGNOSTIC TROUBLE CODE DEFINITIONS . If no DTCs are displayed, system is okay.