Diagnostic Procedures
- Perform On-Board Diagnostic (OBD) System Check. After performing OBD system check, go to next step.
- If DTC P0460 is also set, go to that DTC first. If not, go to step 3).
- Check fuel cap for missing or loose condition. If problem is found, repair as necessary and go to step 20). If repair is not necessary, go to next step.
- Turn ignition on, with engine off. Using scan tool, command EVAP canister purge valve and EVAP vent solenoid on and off. If purge valve and vent solenoid click, go to next step. If purge valve and/or vent solenoid do not click, go to PCM OUTPUTS DIAGNOSIS.
- Ignition off. Remove fuel filler cap. Ignition on. If fuel tank pressure parameter on scan tool is less than one in. H2O, go to step 8). If not less than one in. H2O, go to next step.
- If battery has been disconnected, go to appropriate SYSTEM/COMPONENT TESTS article to diagnose evaporative control system. If not, go to next step.
- Disconnect battery cables. Go to step 5).
- Reinstall fuel cap. Using scan tool, command EVAP vent solenoid on (closed). Zero EVAP pressure and vacuum gauges on EVAP Pressure/Purge Cart (J-41413). Connect EVAP pressure/purge cart to EVAP service port. Attempt to pressurize EVAP system to 5 in. H2O. Monitor pressure using gauge on EVAP pressure/purge cart. If pressure can be achieved, go to next step. If pressure cannot be achieved, go to step 10).
- Maintain EVAP system pressure at 5 in. H2O. Using scan tool, observe FUEL TANK VACUUM PRESSURE. If pressure reading is 3-7 in H2O, go to step 12). If pressure reading is not 3-7 in. H2O, go to step 11).
- Disconnect fuel tank vapor and EVAP purge hoses from EVAP canister. Plug canister fitting for fuel tank vapor hose. Ensure EVAP vent solenoid is still commanded on. Connect a hand-held vacuum pump to EVAP purge hose fitting on EVAP canister and apply 5 in. Hg. If vacuum holds, go to step 15). If vacuum does not hold, go to step 14).
- Check for restricted fuel tank vapor and EVAP purge hoses. Repair as necessary. After repair is completed, go to step 20). If hoses are okay, check fuel tank pressure sensor. See appropriate SYSTEM/COMPONENT TESTS article. Replace fuel tank pressure sensor or repair related wiring as necessary.
- Disconnect vacuum hose at EVAP canister purge valve (from throttle body). Connect a hand-held vacuum pump to EVAP canister purge valve vacuum source fitting. Apply 10 in. Hg. Using scan tool, command EVAP canister purge valve on. If vacuum is released, go to next step. If vacuum holds, go to step 17).
- Connect a vacuum gauge to EVAP canister purge valve vacuum hose (from throttle body). Start engine. Increase engine speed to 2500 RPM. If vacuum is greater than 10 in. Hg, see DIAGNOSTIC AIDS. If vacuum is 10 in. Hg or less, go to step 18).
- Check for disconnected or damaged vent hose. Also, check for damaged EVAP canister. Repair as necessary. After repair is completed, go to step 20). If no problem is found, go to step 19).
- Check for missing or faulty fuel cap. Check for disconnected or leaking fuel tank vapor hose or disconnected or damaged EVAP purge hose. Repair as necessary. After repair is completed, go to step 20). If no problem is found, go to next step.
- Using scan tool, command EVAP vent solenoid on. With EVAP pressure/purge cart connected to EVAP service port, attempt to pressurize EVAP system by leaving cart control knob in PRESSURIZE position. Using Ultrasonic Leak Detector (J-41416), locate and repair EVAP system leak. It may be necessary to partially lower fuel tank to examine hose connections at top of tank. After repair is completed, go to step 20).
- Replace EVAP canister purge valve. After repair is completed, go to step 20).
- Locate and repair cause of low or no vacuum. After repair is completed, go to step 20).
- Replace EVAP vent solenoid. After repair is completed, go to next step.
- Turn ignition on, with engine off. Using scan tool, command EVAP vent solenoid on (closed). Using EVAP pressure/purge cart, pressurize EVAP system to 15 in. H2O. Set rotary switch on pressure/purge cart to HOLD and observe EVAP pressure gauge. If pressure decreases to less than 10 in. H2O within 2 minutes, system is functioning properly. If pressure does not decrease to less than 10 in. H2O within 2 minutes, go to step 3).