LEMON Manuals: Even more car manuals for everyone
Home >> Cadillac >> 2003 >> Seville STS >> Repair and Diagnosis >> Brakes >> Traction Control >> Antilock Brake System >> Repair Instructions >> Brake Pressure Modulator Valve (BPMV) Replacement >> Removal Procedure

Removal Procedure

CAUTION: For safety reasons, the brake pressure modulator valve assembly must not be repaired, the complete unit must be replaced. With the exception of the EBCM, no screws on the brake pressure modulator valve assembly may be loosened. If screws are loosened, it will not be possible to get the brake circuits leak-tight and personal injury may result.
  1. Turn OFF the ignition.
  2. Raise the vehicle. Refer to LIFTING AND JACKING THE VEHICLE in General Information.
  3. Remove the left front wheel. Refer to TIRE AND WHEEL REMOVAL AND INSTALLATION  in Tire and Wheels.
  4. Remove the left front fascia extension. Refer to BUMPER SYSTEM  in Bumpers.
  5. Remove the front air deflector. Refer to BODY FRONT END  in Body Front End.
    IMPORTANT: The area around the electronic brake control module (EBCM)/brake pressure modulator valve (BPMV) must be free from loose dirt to prevent contamination of disassembled ABS components.
  6. Thoroughly wash all contaminants from around the EBCM/BPMV.
  7. Rotate the EBCM connector tab up to the unlocked position.
  8. Disconnect the EBCM connector position assurance (2) from the EBCM electrical connector (1).
    NOTE: To prevent equipment damage, never connect or disconnect the wiring harness connection from the EBCM with the ignition switch in the ON position.
  9. Disconnect the EBCM electrical connector (1) from the EBCM (4).
    CAUTION: Brake fluid may irritate eyes and skin. In case of contact, take the following actions:
    • Eye contact-rinse thoroughly with water.
    • Skin contact-wash with soap and water.
    • If ingested-consult a physician immediately.
    NOTE: When removing the brake pressure modulator valve, protect the vehicle exterior from possible brake fluid spillage. Brake fluid can cause damage to painted surfaces.
    NOTE: Excessive bending of brake pipes during BPMV removal or installation may cause permanent damage that will require replacement.
    IMPORTANT: Record the location of all brake pipes to the BPMV for use as an aid during installation.
  10. Remove the 2 master cylinder brake pipes (1) from the BPMV (2).
    Fig 1: Removing Master Cylinder Brake Pipes From BPMV
    G02069252Courtesy of GENERAL MOTORS CORP.
  11. Remove the 4 wheel brake pipes (1) from the BPMV (2).
    Fig 2: Removing Wheel Brake Pipes From BPMV
    G02069253Courtesy of GENERAL MOTORS CORP.
  12. Clean any brake fluid spillage from the BPMV (1).
  13. Remove the 2 BPMV bracket nuts (2).
  14. Remove the EBCM/BPMV assembly (1) from the BPMV bracket (3).
    Fig 3: Removing EBCM/BPMV Assembly From BPMV Bracket
    G02069254Courtesy of GENERAL MOTORS CORP.
  15. Disconnect the BPMV electrical connector (2) from the EBCM (3).
    Fig 4: Disconnecting BPMV Electrical Connector From EBCM
    G02069255Courtesy of GENERAL MOTORS CORP.
  16. Remove the 6 EBCM to BPMV screws (2).
    Fig 5: Removing EBCM To BPMV Screws
    G02069256Courtesy of GENERAL MOTORS CORP.
  17. Clean the surface of the EBCM/BPMV assembly.
  18. Remove the EBCM (2) from the BPMV (1).
    Fig 6: Removing EBCM From BPMV
    G02069257Courtesy of GENERAL MOTORS CORP.