LEMON Manuals: Even more car manuals for everyone
Home >> Buick >> 2019 >> Regal Preferred >> Repair and Diagnosis >> Suspension >> Suspension Control Systems >> Diagnostic Information and Procedures >> DTC C0670 or C0675 >> Circuit/System Testing

Circuit/System Testing

  1. Ignition ON, verify that DTC C0870 is not present.
    • If the DTC C0870 is present,  refer to DTC C0870 
    • Go to next step: If the DTC C0870 is not present 
  2. Vehicle OFF and all vehicle systems OFF. Disconnect the harness connector at the appropriate B161 Vertical Suspension Acceleration Sensor. It may take up to 2 min for all vehicle systems to power down.
  3. Test for less than 10 Ω between the low reference circuit terminal 2 and ground.
    • If 10 Ω or greater 
    1. Vehicle OFF, disconnect the harness connector at the K19 Suspension Control Module.
    2. Test for less than 2 Ω in the low reference circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K19 Suspension Control Module.
    • Go to next step: If less than 10 Ω 
  4. Vehicle in Service Mode.
  5. Test for 4.8 - 5.2 V between the 5 V reference circuit terminal 1 and ground.
    • If less than 4.8 V 
    1. Vehicle OFF, disconnect the harness connector at the K19 Suspension Control Module.
    2. Test for infinite resistance between the 5 V reference circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • Go to next step: If infinite resistance
    3. Test for less than 2 Ω in the 5 V reference circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K19 Suspension Control Module.
    • If greater than 5.2 V 
    1. Vehicle OFF, disconnect the harness connector at the K19 Suspension Control Module, vehicle in Service Mode.
    2. Test for less than 1 V between the 5 V reference circuit and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V, replace the K19 Suspension Control Module.
    • Go to next step: If within 4.8 - 5.2 V 
  6. Vehicle OFF, disconnect the harness connector at the K19 Suspension Control Module, vehicle in Service Mode.
  7. Test for less than 1 V between the appropriate B161 Vertical Suspension Acceleration Sensor signal circuit terminal 3 and ground.
    • If greater than 1 V 

      Repair the short to voltage on the circuit.

    • Go to next step: If less than 1 V 
  8. Vehicle OFF.
  9. Test for infinite resistance between the appropriate B161 Vertical Suspension Acceleration Sensor signal circuit terminal 3 and ground.
    • If less than infinite resistance 

      Repair the short to ground on the circuit.

    • Go to next step: If infinite resistance 
  10. Test for less than 2 Ω between the appropriate B161 Vertical Suspension Acceleration Sensor signal circuit terminal 3 and the K19 Suspension Control Module signal circuit listed below.
    • Terminal 10
    • Terminal 11
    • If 2 Ω or greater 

      Repair the open/high resistance in the circuit.

    • Go to next step: If less than 2 Ω 
  11. Replace the appropriate B161 Vertical Suspension Acceleration Sensor.
  12. Verify the DTC does not set while operating the vehicle under Conditions for Running the DTC.
    • If the DTC sets 

      Replace the K19 Suspension Control Module.

    • Go to next step: If the DTC does not set 
  13. All OK.