LEMON Manuals: Even more car manuals for everyone
Home >> Buick >> 2001 >> LeSabre Custom, 4T65E/MN3 >> Repair and Diagnosis >> Engine Performance >> System >> Engine Control System Self-Diagnostics - 3.8L >> Diagnostic Tests >> DTC P0102: MAF Sensor Circuit - Low Frequency >> Diagnostic Procedures

Diagnostic Procedures

  1. Perform powertrain diagnostic system check. See POWERTRAIN DIAGNOSTIC SYSTEM CHECK  under SELF-DIAGNOSTIC SYSTEM. After performing powertrain diagnostic system check, go to next step.
  2. Install scan tool. Start engine. Using scan tool observe frequency parameter of MAF sensor. If scan tool indicates MAF sensor frequency is less than 1200 Hz, go to step  4. If scan tool indicates MAF sensor frequency is not less than 1200 Hz, go to next step.
  3. Observe FREEZE FRAME AND/OR FAILURE RECORDS data for this DTC. Turn ignition off for 30 seconds. Start engine. Operate vehicle within code enable criteria, or as close to FREEZE FRAME AND/OR FAILURE RECORDS data as possible. If DTC failed this ignition cycle, go to next step. If DTC did not fail this ignition cycle, see DIAGNOSTIC AIDS .
  4. Check fuse for ignition 1 voltage circuit of MAF sensor. If fuse is open, go to step  14. If fuse is okay, go to next step.
  5. Turn ignition off. Disconnect MAF sensor connector. See Figure or Figure . Turn ignition on, engine off. Measure voltage MAF sensor connector terminal "A" (Yellow wire) and ground. See Figure. If voltage is about 5.0 volts, go to next step. If voltage is not about 5.0 volts, go to step  8.
  6. Turn ignition off. Connect a fused jumper wire (3-amp) between MAF sensor connector terminal "A" (Yellow wire) and ground. Start engine. If any additional DTCs set, go to step  16. If no additional DTCs set, go to next step.
  7. Turn ignition off. Connect a test light between MAF sensor connector terminals "B" (Black/White wire) and "C" (Pink wire). Turn ignition on, engine off. If test light is on, go to step  18. If test light is off, go to step  11.
  8. If voltage is less than 4.5 volts, go to step  10. If voltage is not less than 4.5 volts, go to next step.
  9. NOTE: Disconnecting PCM connectors may eliminate short to voltage if signal circuit is shorted to another PCM circuit.
  10. Turn ignition off. Disconnect PCM. Turn ignition on, engine off. Measure voltage between MAF sensor connector terminal "A" (Yellow wire) and ground. If voltage is about zero volts, go to step  12. If voltage is not about zero volts, go to step  15.
  11. Turn ignition off. Disconnect PCM. Check Yellow wire between PCM and MAF sensor for high resistance, open, short to ground, or short to Black/White wire. If problem was found, repair as necessary. After repairs, go to step  22. If problem was not found, go to step  12.
  12. Connect a test light between MAF sensor connector terminal "C" (Pink wire) and ground. If test light is on, go to step  13. If test light is off, go to step  14.
  13. Using a DVOM, check continuity between PCM connector C1 terminal No. 69 (Yellow wire) and all other terminals in both PCM connectors. See Figure. If continuity exists between any circuits, go to step  17. If continuity does not exist between any circuits, go to step  19.
  14. Repair high resistance or open Black/White wire between MAF sensor and PCM. After repairs, go to step  22.
  15. NOTE: Ignition 1 voltage circuit of MAF sensor is spliced to other components on vehicle.
  16. Repair short to ground or open in Pink wire between MAF sensor and fuse. Replace fuse if necessary. After repairs, go to step  22.
  17. Repair short to voltage in Yellow wire between MAF sensor PCM. After repairs, go to step  22.
  18. Repair short between Yellow wire and circuit for which DTC set. After repairs, go to step  22.
  19. Repair circuits that are shorted together. After repairs, go to step  22.
  20. Check MAF sensor connector for poor connections. If problem was found, repair as necessary. After repairs, go to step  22. If problem was not found, go to step  20.
  21. Check PCM connectors for poor connections. If problem was found, repair as necessary. After repairs, go to step  22. If problem was not found, go to step  21.
  22. Replace MAF sensor. After repairs, go to step  22.
  23. Replace PCM. Program replacement PCM. See POWERTRAIN CONTROL MODULE  under PROGRAMMING. After repairs, go to next step.
  24. Using scan tool, clear DTCs. Turn ignition off for 30 seconds. Start engine. Operate vehicle within code enable criteria. If DTC runs and passes, go to next step. If DTC does not run and pass, go to step  2.
  25. Using scan tool, observe stored information. If scan tool displays any DTCs that have not been diagnosed, see DIAGNOSTIC TROUBLE CODE DEFINITIONS . If scan tool does not display any DTCs, system is okay.