LEMON Manuals: Even more car manuals for everyone
Home >> Buick >> 2001 >> Century Custom >> Repair and Diagnosis >> Body & Frame >> Seats >> Power Seat System >> System Tests >> Test B: Lumbar Support Inoperative

Test B: Lumbar Support Inoperative

NOTE: Reviewing system description and operation information will help determine if condition described by customer is normal operation, and may help determine correct symptom diagnostic procedure when a malfunction exists.
  1. If lumbar system description and operation has been reviewed, go to next step. If description and operation has not been reviewed, see LUMBAR SUPPORT SYSTEM  under DESCRIPTION & OPERATION.
  2. Attempt to adjust lumbar support up, down, in and out. If all lumbar support functions do not operate properly, go to next step. If all lumbar support functions operate properly, go to DIAGNOSING INTERMITTENTS  .
  3. If all lumbar support functions are inoperative, go to next step. If not all lumbar support functions are inoperative, go to step  5 .
  4. Test Orange wire between instrument panel fuse block and lumbar adjuster switch 6-pin harness connector terminal "E" for an open or high resistance. See Fig 1 . See WIRING DIAGRAMS  . If an open or high resistance is not found, go to next step. If an open or high resistance is found, repair as necessary. After repair, go to step  16
  5. Using a test light, backprobe between suspect lumbar adjuster relay 6-pin harness connector terminals "B" and "E". See Fig 1 or Fig 2 . See WIRING DIAGRAMS  . Lumbar adjuster relays are located under driver seat. Press suspect lumbar adjuster switch in both directions. If test light does not illuminate when switch is pressed in both directions, go to next step. If test light illuminates when switch is pressed in both directions, go to step  9 .
  6. Remove suspect lumber adjuster relay. Connect a test light between ground and suspect lumbar adjuster relay 6-pin harness connector terminal "C" (Orange wire). If test light illuminates, go to next step. If test light does not illuminate, go to step  11 .
  7. Connect test light between suspect lumbar adjuster relay 6-pin harness connector terminals "C" and "D". See Fig 1 or Fig 2 . See WIRING DIAGRAMS  . If test light illuminates, go to next step. If test light does not illuminate, go to step  12 .
  8. Connect test light between ground and appropriate lumbar adjuster switch signal circuit terminal at suspect lumbar adjuster relay 6-pin harness connector. See Fig 1 or Fig 2 . See WIRING DIAGRAMS  . Press suspect lumbar adjuster switch. If test light does not illuminate, go to step  10 . If test light illuminates, go to step  14 .
  9. Test wires between suspect lumbar support motor 2-pin harness connector and suspect lumbar adjuster relay 6-pin harness connector terminals "B" and "E" for an open, high resistance or short to ground. See Fig 1 or Fig 2 . See WIRING DIAGRAMS  . If open, high resistance or short to ground is not found, go to step  15 . If open, high resistance or short to ground is found, repair as necessary. After repair, go to step  16 .
  10. Test wires between suspect lumbar support lumbar adjuster relay 6-pin harness connector and lumbar adjuster switch 6-pin harness connector for an open, high resistance or short to ground. See Fig 1 or Fig 2 . See WIRING DIAGRAMS  . If open, high resistance or short to ground is not found, go to step  13 . If open, high resistance or short to ground is found, repair as necessary. After repair, go to step  16 . 16 .
  11. Repair open, high resistance or short to ground in Orange wire between suspect lumbar adjuster relay 6-pin harness connector and instrument panel fuse block. After repair, go to step  16 .
  12. Repair open, high resistance or short to ground in Black wire between suspect lumbar adjuster relay 6-pin harness connector and ground point. Ground point is located inside left door sill, forward of left front seat. After repair, go to step  16 .
  13. Replace lumbar adjuster switch. See POWER SEAT SWITCHES  under REMOVAL & INSTALLATION. After repair, go to step  16 .
  14. Replace lumbar adjuster relay. After repair, go to step  16 .
  15. Replace lumbar adjuster motor. See LUMBAR ASSEMBLY  under REMOVAL & INSTALLATION. After repair, go to next step.
  16. Operate system to verify repair. If system does not operate properly, go to step  3 . If system operates properly, system is okay.
Fig 1: Identifying Lumbar Switch & Lumbar Horizontal Adjuster Relay Harness Connector Terminals
G98I12367Courtesy of GENERAL MOTORS CORP.
Fig 2: Identifying Lumbar Vertical Adjuster Relay Connector Terminals
G99H02291Courtesy of GENERAL MOTORS CORP.