LEMON Manuals: Even more car manuals for everyone
Home >> BMW >> 2021 >> X3 M Base >> Repair and Diagnosis >> Quick Lookups >> Technical Bulletins >> Technical Service Bulletins >> Anti-Theft Systems >> Remote Control Is Not Detected (SI B66 24 19)

Remote Control Is Not Detected (SI B66 24 19)

Publication date: 2022-09-06
Reference number: SI B66 24 19

REMOTE CONTROL IS NOT DETECTED

REMOTE CONTROL IS NOT DETECTED

TECHNICAL SERVICE BULLETIN

Reference Number(s): SI B66 24 19, Date of Issue:  September 06, 2022
BMW: F44 2 Series Gran Coupe; F90 M5 Sedan; F91 M8 Convertible; F92 M8 Coupe; F93 M8 Gran Coupe; F95 X5 M Sports Activity Vehicle; F96 X6 M Sports Activity Coupe; F97 X3 M Sports Activity Vehicle; F98 X4 M Sports Activity Coupe; G01 X3 Sports Activity Vehicle; G02 X4 Sports Activity Vehicle; G05 X5 Sports Activity Vehicle; G06 X6 Sports Activity Coupe; G07 X7 Sports Activity Vehicle; Start of production; G12 7 Series Sedan From March 1st, 2019 (LCI); G14 8 Series Convertible; G15 8 Series Coupe; G16 8 Series Gran Coupe; G20 3 Series Sedan; G22 4 Series Coupe; G26 4 Series Gran Coupe; G29 Z4 Roadster; Start of production; G30 5 Series Sedan G32 640i xDrive Gran Turismo; From July 1st, 2020 (LCI); G42 2 Series Coupe; G80 M3 Sedan Start of Production; G82 M4 Coupe; G83 M4 Convertible; Start of production

SERVICE INFORMATION

This Service Information Bulletin (Revision 6) replaces SI B66 24 19 dated June 2022. 

What's New  (Specific text highlighted):

SITUATION

Vehicle cannot be opened or closed using comfort access, engine start is not possible, and the vehicle may not start when placing the key against the steering column.

NOTE: Opening, closing and starting via the BMW Digital Key or the Digital Key Card are not affected.

CAUSE

Software error in the BDC (Body Domain Controller) module.

CORRECTION

Update the vehicle software.

PROCEDURE

  1. Perform a BDC reset through the control unit tree using ISTA. Also, a battery reset if needed when no key recognition is possible.
  2. Perform the following Test modules:
    • Test module "Comfort Access aerials": AT6100_BD2ANFUA --> in the case of a general key complaint
    • Test module "Ring aerial": AT6100_TSFUA --> In the case of the complaint "Engine start via ring aerial not possible"
  3. Ensure all key are recognized.
  4. Are all keys recognized by the vehicle?

    Yes  : Proceed to Step 5

    No  : Further diagnosis with ISTA is needed

  5. Is the vehicle current integration level S18A-21-03-500/S15A-21-03-500  or higher?

    Yes:  Do not program the vehicle and perform diagnosis with ISTA

    No:  Proceed to Step 6

  6. Program the vehicle using ISTA 4.28.2x  or higher (released March 2021).
    Model Target integration level
    F44, F90, F91, F92, F93, F95, F96, G05, G06, G07, G14, G15, G16, G20, G29 S18A-21-03-500  or higher
    G12, G30 S15A-21-03-500  or higher
  7. Perform vehicle sleep cycle until the lighting of the hazard warning switch goes out.
  8. Carry out a battery reset to resynchronize the vehicle keys with the BDC.
  9. Clear faults and ensure the vehicle can be started and comfort access is functioning.

Note that ISTA will automatically reprogram and code all programmable control modules that do not have the latest software.

Always connect a BMW-approved battery charger/power supply ( SI B04 23 10  ). 

For information on programming and coding with ISTA, refer to DealerSpeed/TIS/Technical Documentation/Diagnostics and Programming/Programming Documentation.

CLAIM INFORMATION

During this workshop visit, the affected vehicle may show one or more programming and encoding Technical Campaign repairs open, the programming and encoding procedure may only be invoiced one time.

Select one of these open Technical Campaigns to perform and submit for updating the vehicle's software to the required I-level or higher. 

Please be sure to perform any additional before and/or after work (including attaching labels) as required by the open campaigns on the vehicle. Close any remaining open programming and encoding Campaign repairs as outlined in the corresponding Service Information Bulletin. 

Only if the above situation does not apply, the BMW software solution is then:

Covered under the terms of the BMW New Vehicle Limited Warranty for Passenger Cars and Light Trucks, or the BMW Certified Pre-Owned Program as described below.

Defect Code: 6138270200 BDC Body Domain Controller software error/internal equipment fault

Refer to AIR for the corresponding flat rate unit (FRU) allowances.

Labor Operation Description Labor Allowance
00 00 006 Performing vehicle test (with vehicle diagnosis system - checking faults) (Main work) Refer to AIR
Or:    
00 00 556 Performing vehicle test (with vehicle diagnosis system - checking faults) (Plus work) Refer to AIR
And:    
61 21 528 Support voltage of the vehicle electrical system/recharge vehicle electrical system battery Refer to AIR
And, as necessary:    
61 00 006* Performing vehicle diagnosis - test module Work time (WT)
Or    
00 58 500* Diagnosis Worktime Flat Rate (See below) 2 FRU
And:    
61 00 730 Programming/encoding control unit(s) Refer to AIR

If you are using a Main labor code for another repair, use the Plus code labor operation 00 00 556 instead of 00 00 006, or exclude (including 61 21 528) when the Vehicle Test is included in another repair.

Work time labor operation codes 61 00 006 and 00 58 500 are not considered a Main labor operations.

*Based on which one applies to your center, please refer to SI B01 01 20 or B01 07 20 for the applicable procedure for documenting, claiming, and explaining, on the RO and in the claim comments, your diagnosis work time (WT), job/repair work time (WT), and the vehicle repairs your center performed, unless otherwise required by State law.

PROGRAMMING AND ENCODING - VEHICLE CONTROL UNITS (RO AND CLAIM COMMENTS REQUIRED)

This procedure automatically reprograms and encodes any vehicle control modules that do not have the latest software I-level.

If one or more control modules fail during the reprogramming procedure, claim the required consequential repair work procedures to address this issue (including performing the IRAP Control Unit Recovery first as required, refer to the SIB in AIR) under the Defect Code in this bulletin with the labor operations in AIR that apply.

Please explain the additional work procedures that were performed (The why and the what) on the repair order and in the claim comments.

For covered repairs that address control module failures that occurred prior to performing this reprogramming procedure, claim this work with the Defect Code and labor operations (including diagnosis that applies*) in AIR that apply.

OTHER REPAIRS

If other eligible and covered work is performed because of performing the ISTA diagnostics and related test plans, claim this work with the applicable Defect Code and the labor operations listed in AIR (including diagnosis that applies*).

FEEDBACK REGARDING THIS BULLETIN

Technical Feedback To submit feedback for the technical topics of this bulletin: Submit your feedback in the rating box at the top of this bulletin
Warranty Feedback To submit feedback for the CLAIMS section of this bulletin: Submit an IDS ticket to the Warranty Department, or use the chat available in the Warranty Documentation Portal
Parts Feedback To submit feedback for the PARTS section of this bulletin: Submit an IDS ticket to the Parts Department