Service Action 275 - Retrofitting Adapter Cable For MK II Plus Navigation Computer (84 06 00)
Publication date: 2000-08-01Reference number: 84 06 00
SERVICE ACTION 275 - RETROFITTING ADAPTER CABLE FOR MK II PLUS NAVIGATION COMPUTER
SERVICE CAMPAIGN BULLETIN
| BMW: | E38, 7 Series with standard BMW Navigation System; E39, 5 Series with optional BMW Navigation System; E46, 3 Series with optional BMW Navigation System; |
| GROUP: | 84 - Phone, Navigation Systems |
PERFORM THE PROCEDURE OUTLINED IN THIS SERVICE INFORMATION ON ALL AFFECTED VEHICLES THE NEXT TIME THEY ARE IN THE SHOP FOR MAINTENANCE OR REPAIRS.
SUBJECT
Retrofitting Adapter Cable for MK II Plus Navigation Computer on E38, E39 E46 Vehicles
SITUATION I
This situation applies when no customer complaint of a navigation failure is received. The resistors installed in the input circuitry of the Navigation Computer can fail (due to an overloading condition), causing irreversible damage to the Navigation Computer. As a result of such a failure, the screen of the on-board monitor will remain white or black permanently (without displayed image), and the audio system of the vehicle will be inoperative.
To protect these resistors against overloading (and to avoid the situation described above), a special adapter cable with an integrated resistance module has been developed. The adapter cable has to be installed between the Navigation Computer and the vehicle navigation wiring harness.
The Customer Notification Letter is attached.
SITUATION II
This situation applies when no customer complaint of a permanently black or white screen is received. In case of a total Navigation Computer failure, after switching the ignition ON the screen of the on-board monitor remains white or black permanently, and no image is displayed. Both LED's on the Navigation Computer are off, and it is no longer possible to eject the road map CD from the Navigation computer drive. The Navigation Computer has been irreversibly damaged due to the failure of input circuitry resistors.
AFFECTED VEHICLES
This Service Action involves E38, E39 and E46 vehicles equipped with a BMW Navigation System which were produced from May 1999 to October 1999.
To determine if a specific vehicle is affected by this Service Action, it will be necessary to utilize the "Service Menu" of the DCS (Dealer Communication System). Based on the response of the system, either proceed with the corrective action or take no further action.
The Chassis Number Ranges listed below are only for informational purposes and are not to be considered as the only deciding factor.
| Model | Chassis Number Range |
|---|---|
| 323i | KC62649 - KC68016 |
| 323iA | FP63580 - FP71306 |
| 328i | EJ40055 - EJ41409 |
| 328i | KG10408 - KG10488 |
| 328i | KG17031 - KG17946 |
| 328iA | FR11529 - FR11940 |
| 328iA | FR15004 - FR17585 |
| 328iA | JR56603 - JR58019 |
| 323iT | JM00006 - JM00018 |
| 323Ci | JN60282 - JN61896 |
| 323CiA | JN80319 - JN82537 |
| 328Ci | JP00308 - JP01720 |
| 328CiA | JN92439 - JN92804 |
| 528i | BY17211 - BY18003 |
| 528iA | GU03336 - U10628 |
| 528iT | BR95356 - BR95543 |
| 528iAT | BV63040 - BV64494 |
| 540i | GC92997 - GC94108 |
| 540iA | GM64205 - GM65849 |
| 540iAT | GN90890 - GN91125 |
| M5 | BZ94010 - BZ94210 |
| 740iA | DN76845 - DN78704 |
| 740iLA | DE05009 - DE05028 |
| 740iLA | DP08591 - DP12806 |
| 750iLA | DD73661 - DD73871 |
| 750iLP | DE35010 - DE35027 |
CORRECTION I
On the affected vehicles first verify if the improved Navigation Computer has already been installed, as per enclosed procedure. If the old type unit is still installed, then retrofit a navigation adapter cable between the navigation computer and the vehicle wiring harness.
CORRECTION II
Only in case of a permanent Navigation Computer failure, replace the unit with an improved part (P/N 65 90 6 908 311), load with current version of Navigation operating software (CD V15.0 or higher), and recode using DIS/MoDiC version CD 22.0 or later. Perform Campaign Entry into DCS System, and affix the campaign label after replacing failed Navigation Computer
IMPORTANT NOTE: The appropriate map software CD must be ordered from Navigation Technologies.
When calling the NavTech Hot Line, you have to provide the following information in order to receive a free of charge map CD (special program for service applications only):
- Personal identification
- BMW center name, address, and dealer code
- Affected VIN
- Appropriate map CD selection (region of the country).
Ordering CD maps without justification (no warranty claim filed), will incur a charge of $127.00 per CD map.
PROCEDURE I
- 1) Switch the ignition off.
- 2) Open the rear left-hand side trim panel in the trunk.
- 3) Using the special tool (1) (65 5 400), release and remove the navigation computer (for removal instructions, please refer to RA 65 90 510). See Fig 2 .
- 4)
Check the part number on the label attached to the navigation computer. See Fig 3
. If the part number is:
- 65 90 8 386 849, or
- 65 90 8 385 439, or
- 65 90 8 386 851 then continue with the step 5.
If the part number differs from those listed above, the navigation computer has already been replaced with the updated part, and NO action is required.
E38 Vehicles:
- 5) Disconnect two connectors (blue and violet) at the back of the nav. computer.
- 6) Unclip and remove the computer's plastic trim panel (1). See Fig 4 .
- 7) Remove trim panel over the Nav/DSP/CD changer (for removal instructions, please refer to RA 51 47 172).
- 8) Remove trim panel at the rear left wheel housing (for removal instructions, please refer to RA 51 47 151).
- 9)
Push the computer's connector cable back and route it over the computer's support bracket, towards the wheel housing.
IMPORTANT: Cable must be routed over the support, otherwise it will be pinched when the nav. computer is installed.
- 10)
Route the adapter cable as shown in Fig 5
(above the navigation computer support), connect it into the vehicle harness plug and into the navigation computer. Secure the plug connector (1) and the resistance module (2) with the cable straps.
IMPORTANT: Make sure that the adapter cable does not rub against any body components, or it is not trapped between the computer and its housing.
- 11) Reinstalled all removed parts.
- 12) Perform a functional check: turn ignition ON, from the main menu screen select Navigation.
E39 sedan:
- 5) Disconnect two connectors (blue and violet) at the back of navigation computer.
- 6) Remove the navigation connector cable from the computer support housing, and route it towards the radio (down and closer to the taillight).
- 7)
Route the adapter cable as shown in Fig 6
, connect it into the vehicle harness plug and into the navigation computer. Secure the plug connector (1) and the resistance module (2) with the cable straps.
IMPORTANT: Make sure that the adapter cable does not rub against any body components, or it is not trapped between the computer and its housing.
- 8) Reinstalled all removed parts. Perform a functional check: turn ignition ON, from the main menu screen select Navigation.
E39 sport wagon:
- 5) Disconnect two connectors (blue and violet) at the back of navigation computer.
- 6) Remove the navigation connector cable from the computer support housing, and route it downwards (if a DSP amplifier, or an Alpine CD changer is installed the adapter cable must be routed downwards and to the left of such an equipment).
- 7)
Route the adapter cable as shown in Fig 7
, connect it into the vehicle harness plug and into the navigation computer. Secure the plug connector (1) and the resistance module (2) with the cable straps.
IMPORTANT: Make sure that the adapter cable does not rub against any body components, or it is not trapped between the computer and its housing.
- 8) Reinstalled all removed parts. Perform a functional check: turn ignition ON, from the main menu screen select Navigation.
E46 Vehicles:
- 5) Disconnect two connectors (blue and violet) at the back of the navigation computer.
- 6) Remove trim panel at the rear left wheel housing (for removal instructions, please refer to RA 51 47 151).
- 7)
Push the computer's connector cable back and route it over the computer's support bracket, towards the wheel housing.
IMPORTANT: Cable must be routed over the support, otherwise it will be pinched when the navigation computer is installed.
- 8)
Route the adapter cable behind the navigation computer, connect it into the vehicle harness plug and into the navigation computer. Secure the plug connector (1) and the resistance module (2) with the cable straps. See Fig 8
.
IMPORTANT: Make sure that the adapter cable does not rub against any body components, or it is not trapped between the computer and its housing.
- 9) Reinstalled all removed parts.
- 10) Perform a functional check: turn ignition ON, from the main menu screen select Navigation.
PROCEDURE II
- Switch the ignition off.
- Open the rear left-hand side trim panel in the trunk
- Using the special tool (1) (65 5 400), release and remove the navigation computer (for removal instructions, please refer to RA 65 90 510). See Fig 9 .
- Install improved unit (P/N 65 90 6 908 311), load the Operating Software CD V 15.0 (for loading procedure refer to Service Information Bulletin 84 11 97 ), and recode with DIS/MoDiC CD 22.0.
LABEL INSTRUCTIONS
This Service Action has been assigned code number 275. After the vehicle has been checked, and corrected if necessary, obtain a label (SD 92-120) and:
- emboss your BMW dealer warranty number in the middle of the label (1);
- punch out code number 275 printed on the label and,
- affix the label to the B pillar as shown in Fig 10 .
If the vehicle already has a label from a previous Service Action/Recall Campaign, affix the new label next to the old one. Do not affix one label on top of another one because a number from an underlying label could appear in the punched-out hole of the new label.
WARRANTY INFORMATION
Reimbursement for this Service Action will be provided through Campaign Entry.
- For E46 - 323i, 323iA, 328i, 328iA, 323Ci, 323CiA, 328Ci, 328CiA, 323iT, 323iAT;
- For E38 - 740i, 740iL;
- For E39 - 528i, 528iA, 528iAT, 540i, 540iA, 540iAT, M5:
WORK PACKAGE #1
Check part number of Navigation computer.
| Defect Code | Labor Operation | Labor Allowance |
|---|---|---|
| 00 65 41 01 00 | 84 99 000 | 3 FRU |
WORK PACKAGE #2
Check part number of Navigation computer and retrofit adapter cable.
| Defect Code | Labor Operation | Labor Allowance |
|---|---|---|
| 00 65 41 01 00 | 84 99 000 | 7 FRU E38 |
| 00 65 41 01 00 | 84 99 000 | 5 FRU E39 |
| 00 65 41 01 00 | 00 52 749 | 6 FRU E46 sedan, E46 coupe |
| 00 65 41 01 00 | 00 52 749 | 5 FRU E46 touring |
| Part Number | Description | Qty. |
|---|---|---|
| 65 90 4 106 111 | Adapter Cable | 1 |
| 61 13 1 377 134 | Cable strap | 5 |
WORK PACKAGE #3
Replaced failed Navigation Computer.
| Defect Code | Labor Operation | Labor Allowance |
|---|---|---|
| 00 65 41 01 00 | 00 52 112 | 5 FRU |
| Part Number | Description | Qty. |
|---|---|---|
| 65 90 6 908 311 | MK2 Computer | 1 |
WARRANTY INFORMATION
- For E38 with M73TU ONLY - 750iL, and 750iLP:
WORK PACKAGE #1
Check part number of Navigation computer.
| Defect Code | Labor Operation | Labor Allowance |
|---|---|---|
| 00 65 42 01 00 | 00 52 754 | 3 FRU |
WORK PACKAGE #2
Check part number of Navigation computer and retrofit adapter cable.
| Defect Code | Labor Operation | Labor Allowance |
|---|---|---|
| 00 65 42 01 00 | 00 52 755 | 7 FRU |
| Part Number | Description | Qty. |
|---|---|---|
| 65 90 4 106 111 | Adapter Cable | 1 |
| 61 13 1 377 134 | Cable strap | 5 |
WORK PACKAGE #3
Replaced failed Navigation Computer.
| Defect Code | Labor Operation | Labor Allowance |
|---|---|---|
| 00 65 42 01 00 | 00 52 112 | 5 FRU |
| Part Number | Description | Qty. |
|---|---|---|
| 65 90 6 908 311 | MK2 Computer | 1 |
CUSTOMER NOTIFICATION LETTER
July 2000
Dear BMW Owner,
BMW has determined that the Navigation System installed in certain 2000 Model Year BMW automobiles may prematurely fail. As a result of such a failure, the screen of the on-board monitor will permanently remain white (without displayed image), and be non functional. Our records indicate that you are the owner of a potentially affected vehicle.
To protect the Navigation System against such a failure, a special adapter cable has to be fitted between the Navigation Computer and the vehicle wiring harness.
This modification will require approximately one hour and will be performed free of charge by your Authorized BMW center. Additional time will probably be required, depending on the BMW center's scheduling and processing.
PLEASE CONTACT YOUR AUTHORIZED BMW CENTER TO HAVE THE NECESSARY MODIFICATION PERFORMED AS SOON AS POSSIBLE.
If you are no longer the owner of this vehicle, we would appreciate your furnishing us with the name and address of the new owner, using the enclosed return postage-paid card.
Should you have any questions related to this issue, please contact your Authorized BMW center.
We appreciate your confidence in our product, and we wish to do everything we can to retain your confidence. Should you need additional assistance, you may contact BMW Customer Relations at 1-800-831-1117.
BMW of North America, Inc.