LEMON Manuals: Even more car manuals for everyone
Home >> Audi >> 2025 >> Q3 Premium >> Repair and Diagnosis >> Transmission >> Transmission Control Systems >> Controls, Housing >> 37 Controls, Housing >> Transmission, Removing And Installing >> Transmission, Removing >> Removing

Transmission, Removing: Removing

-- Remove The Battery And Battery Tray. Refer To BATTERY .

-- Remove The Subframe Without Steering Gear. Refer To OVERVIEW - SUBFRAME .

-- Remove The Bevel Box. Refer To BEVEL BOX, REMOVING .

-- Remove The Left Front Wheel Housing Liner. Refer To OVERVIEW - FRONT WHEEL HOUSING LINER .

-- Loosen The Hose Clamp -1- And Remove The Air Duct Hose From The Charge Air Cooler.

GWWA21-10943Courtesy of AUDI OF AMERICA, LLC

-- Free Up The Coolant Hose.

GWWA21-10825Courtesy of AUDI OF AMERICA, LLC

-- Free Up The Wiring Harnesses -1 And 2- On The Air Duct Pipe.

-- Loosen The Screw-Type Clamp -4-.

-- Remove The Bolts -Arrows- And Remove The Air Duct Pipe.

-- Disconnect The Connector -1-.

Fig 1: Secondary Air Injection Sensor 1 -G609- / Secondary Air Injection Solenoid Valve -N112- Component Location
GWWA10-11993Courtesy of AUDI OF AMERICA, LLC

-- Remove The Secondary Air Injection Hose -2- By Pressing The Release Buttons On Both Sides.

-- Remove The Starter. Refer To STARTER, REMOVING AND INSTALLING .

GWWN37-10583Courtesy of AUDI OF AMERICA, LLC
CAUTION:

Risk Of Damaging The Selector Mechanism By Incorrectly Installing The Selector Lever.

- Do Not Press The Locking Button On The Selector Lever Handle.

-- Pry The Selector Lever Cable -1- Off The Selector Shaft Lever -2- Using For Example An Open End Wrench.

-- Disconnect The Connector -6- For The Multifunction Transmission Range Switch -F125- And Free Up The Wire On The Bracket.

-- Remove The Bolts -5- For The Cable Bracket -4-. Do Not Remove The Lock Washer -3-.

-- Disengage The Selector Lever Cable -1- From The Bracket Clip -2-.

GWWN37-10584Courtesy of AUDI OF AMERICA, LLC

Tip:

Secure The Selector Lever Cable To A Suitable Position On The Body Using A Cable Tie, For Example.

-- Remove The Bolts -1, 2 And 3- Connecting The Transmission To The Engine Using The :T10179  .

Fig 2: Identifying Transmission Bolts
GWWA37-11389Courtesy of AUDI OF AMERICA, LLC
GWWA37-11388Courtesy of AUDI OF AMERICA, LLC
CAUTION:

Risk Of Destroying Due To Electrostatic Charge.

- Do Not Touch The Connector Terminals.

- Touch A Grounded Object (For Example The Hoist) And Discharge Any Static Electricity.

-- To Discharge Any Static Electricity, Touch The Ground With A Hand (Without Gloves).

-- Disconnect The Connector -2-.

-- To Catch Escaping ATF, Place A Cloth Underneath.

-- Remove The Bolt -1- And Disconnect The ATF Lines.

-- Seal The Open Lines And Connections With Clean Plugs From The :VAS6122  .

-- Remove The Left Drive Axle From The Transmission. Refer To DRIVE AXLE, REMOVING AND INSTALLING .

Fig 3: Using T40263 & T40314
GWWA13-11145Courtesy of AUDI OF AMERICA, LLC
CAUTION:

Risk Of Damaging The Engine By The Timing Mechanism Skipping.

- Turn The Engine Only In The Direction Of Engine Rotation.

-- Use The :T40263  , :T40314  And A 24mm Wrench To Turn The Crankshaft -Arrow- Only Until The Respective Bolt Is Accessible.

-- Remove The Six Nuts -Arrow- For The Torque Converter -1- While Turning The Crankshaft An Additional 60°.

Fig 4: Torque Converter
GWWN37-10591Courtesy of AUDI OF AMERICA, LLC

-- Support The Engine In The Installation Position. Refer To ENGINE, SUPPORTING IN INSTALLATION POSITION (DSNA) , or ENGINE, SUPPORTING IN INSTALLATION POSITION (DSPA) .

-- Completely Remove The Bolts -Arrows- For The Transmission Mount.

Fig 5: Identifying Bolts
GWWN10-10748Courtesy of AUDI OF AMERICA, LLC

-- Using The Spindles On The :10-222B  , Lower The Engine To Dimension -A-.

Fig 6: Turning Spindles On 10 - 222 A And Lower Transmission To Dimension
GWWN34-10994Courtesy of AUDI OF AMERICA, LLC

The Transmission Is Separated From The Engine In This Position.

-- Place The :3282  -A- On The :VAS6931  -B-.

GWWN37-10593Courtesy of AUDI OF AMERICA, LLC

Install The :3282  On The Transmission As Follows With The Mounting Elements:

-- Install The :3282/29  In The Rear Hole For The Pendulum Support Bolt On The Transmission.

-- Support The Transmission By Carefully Lifting It Using The Engine And Gearbox Jack.

-- Remove The Remaining Bolts For The Transmission/Engine Connection.

Fig 7: Identifying Transmission Bolts
GWWA37-11389Courtesy of AUDI OF AMERICA, LLC

-- Pry The Transmission -3- Off The Engine While Pushing The Torque Converter -1- Against The Transmission -Arrow- Using, For Example, A Screwdriver -2-.

GWWA37-11257Courtesy of AUDI OF AMERICA, LLC

-- Carefully Drain The Transmission While Making Sure There Is Clearance To Other Components.

-- After The Removing The Transmission, Secure The Torque Converter From Falling. Refer To Fig 8.

Fig 8: Securing Torque Converter
GWWN37-0702Courtesy of AUDI OF AMERICA, LLC