Lane Change Assistance, Calibrating
Special tools and workshop equipment required
- Calibration Tool: VAS6350A
- Calibration Tool - Spacing Laser: VAS6350/2A
- Calibration Tool - Lane Change Calibration Tool: VAS6350/4
- Calibration Tool - R8 Wheel Adapters: VAS6350/5
- Vehicle Diagnostic Tester
Calibration/Adjustment must be Performed if:
- "No or incorrect basic setting/adaptation" is actively entered in the DTC memory of the Lane Change Assistance Control Module -J769- / Lane Change Assistance Control Module 2 -J770-.
- The Lane Change Assistance Control Module -J769- and/or Lane Change Assistance Control Module 2 -J770- has/have been removed and installed or replaced.
- The rear bumper was removed and installed.
- The rear bumper cover has been damaged or replaced.
- The rear bumper cover was painted near the control modules while installed.
TIP:
When a software update should be made, this must be performed before the calibration.
Preparing for Calibration
- Calibration Tool - Spacing Laser: VAS6350/2A
- For distance measurement
- Refer to the : VAS6350/2A Operating Instructions for handling.
- Calibration Tool: VAS6350A
- Level
- On the : VAS6350A
- To check the horizontal position of the : VAS6350A
- Catch Bracket
- To mount the : VAS6350/2A for the distance measurement
- Distance to the : VAS6350/1A on the rear wheels: dimension -a- = 1700 ± 10 mm
- Calibration Tool - Lane Change Calibration Tool: VAS6350/4
- Is moved from one side of the measuring field to the other during calibration
- When installed correctly, the vehicle electrical system voltage line must be connected at lower left of the calibration device (as seen in direction of travel)
- Brand Emblem
- The linear laser is aligned to the center of the brand emblem
- Calibration Tool - Wheel Center Mounting: VAS6350/1A
- With wheel bolt adapter and measuring paddle
- Measuring Scale
- For positioning the : VAS6350/4
- Calibration Tool - Linear Laser: VAS6350/3A
- With "laser protective eyewear"
- On the : VAS6350A
- Refer to : VAS6350/3A Owner's Manual for handling.
- Plastic Foot
- Quantity: 3
- Adjustable for adjusting the horizontal position of the : VAS6350A
Preliminary Work
- Move the vehicle onto a solid, flat surface.
- Move the wheels so that they are in a straight-ahead position.
- For vehicles with rear axle steering, steer the rear axle to the zero position. Refer to Rear Axle Steering . This is the only way to ensure that the rear axle steering is in the straight-ahead position.
- Vehicles without air suspension: deflect the springs several times and let settle.
- Electromechanical parking brake applied.
- Vehicle exterior lamps switched off.
- All vehicle doors closed.
- Remove the label with the metal foil from the bumper cover, if necessary.
- Connect the battery charger for the battery support mode. Refer to BATTERY, CHARGING .
- Before starting the calibration/adjustment, check the DTC memory and correct all displayed entries.
Procedure
-- Check which hole circle the rims have.
-- On every : VAS6350/1A , attach three fitting wheel bolt adapters for the wheel bolts using the : VAS6350/5 .
-- Insert the measuring paddle at both : VAS6350/1A and secure with the locking nut.
-- Place the : VAS6350/1A onto the wheel bolts on both rear wheels.
- The wheel center mounting rotation center must be in the wheel rotation center.
-- Place the : VAS6350/1A on the wheels so that any "anti-theft wheel bolts" are not connected to the wheel center mounting.
-- Adjust the measuring paddle using the locking nuts so that they move freely just above the floor.
- The measuring paddles must move easily.
- The measuring paddles must be vertical.
-- Position the : VAS6350A at distance -a- to the rear wheels.
- Dimension -a- = 1, 700 ± 10 mm
-- Using the bubble level (level indicator) -arrow-, bring the : VAS6350A into a horizontal position by turning the plastic bases.
-- Wear "laser protective eyewear".
-- Turn on the : VAS6350/3A on the : VAS6350A .
-- Align the : VAS6350A so that the : VAS6350/3A strikes the center of the brand emblem on the rear lid.
-- Turn on the : VAS6350/2A . Refer to : VAS6350/2A Operating Instructions.
The Following Display Appears 1 :
The display -2- shows how to position the : VAS6350/2A .
- -Arrow 1- : position with front edge
- -Arrow 3- : position with rear edge
-- Press the corresponding button.
-- Hold the : VAS6350/2A -2- for the distance measurement on one side of the calibration board flush to the catch bracket, as shown.
- The : VAS6350/2A -2- must lie firmly against the catch bracket.
-- Push the measurement button briefly.
The laser switches on.
-- Make sure the "laser beam" for the distance measurement contacts the lower enlarged part of the measuring paddle -1-.
If that is not the case, correct the measuring paddle -1- height using the clamping screw on the : VAS6350/1A .
-- Use one hand to hold the : VAS6350/2A firmly in the catch bracket on the : VAS6350A ; the laser beam should be seen on the measuring paddle during this.
-- Then press the measurement button for the distance measurement briefly.
Display on : VAS6350/2A :
- "1, 700 m" (specified value: 1700 ± 10 mm).
-- Repeat this measurement on the other side of the : VAS6350A in the same way for the rear wheel.
- The distance value must be the same on both sides.
-- If both measured values are not the same, then readjust the : VAS6350A correspondingly until the distance values are the same on both sides.
-- Make sure the : VAS6350/3A strikes the center above the brand emblem and that the level indicator remains centered. Adjust if necessary.
Calibration Procedure
The following should not occur during the calibration procedure:
- No metallic reflectors may be located within a 2 m radius of the calibration tool (meaning tool carts, metal cabinets).
- Vehicle doors must not be opened or closed.
- People must not sit in the vehicle.
- People must not go between the vehicle and the : VAS6350/4 .
-- Connect the Vehicle Diagnostic Tester.
-- Switch the ignition on.
-- Select and start the Diagnostic operating mode.
-- Select the Test plan tab.
-- Select the Select individual test button and select the following tree structure consecutively:
Vehicles Before Product Improvement
- Body
- Electrical system
- 01 - OBD-capable systems
- 3C - Lane Change Assistance Control Module - J769
- 3C - Lane change assistance control module, functions
- 3C - Calibration
Vehicles from Product Improvement
- Body
- Electrical system
- 01 - OBD-capable systems
- 003C - Lane Change Assistance Control Module - J769
- 003C - Lane change assistance control module, functions
- 003C - Calibration
Continuation for All Vehicles
-- Start the selected program and follow the instructions on the Vehicle Diagnostic Tester display.
TIP:
The following information clarifies which version of the lane change assist is installed.
This information for adjusting the calibration device is important for later steps in the procedure to avoid malfunctions.
-- Secure the : VAS6350/4 to the left rear side on the mount of the : VAS6350A
- When installed correctly, the vehicle electrical system voltage wire must be connected at the bottom left of the calibration device (as seen in direction of travel).
Dimension -a- is measured from the upper edge of the calibration device to the floor.
| Model | Q7 Basis, Before Product Improvement | SQ7/Q7 S-line, Before Product Improvement | Q7 From Product Improvement |
|---|---|---|---|
| Adjustment dimension height in mm dimension -a- | 681 | 675 | 700 |
-- The indicator on the base of the : VAS6350/4 must align with the adjustment dimension on the measuring scale -1- on the measuring field -arrow-.
| Model | Q7 Basis, Before Product Improvement | SQ7/Q7 S-line, Before Product Improvement | Q7 from product improvement |
|---|---|---|---|
| Left adjustment dimension read in mm on the measuring scale -1- | 800 | 817 | 860 |
-- Connect the : VAS6350/4 -1- to the vehicle electrical system voltage and switch it on at the voltage switch -2-.
- The green LED -4- must turn on.
-- If the red LED -3- turns on, then check the : VAS6350/4 -1-.
-- Follow the instructions in the vehicle diagnostic tester display.
During the program sequence, there is a prompt to switch the : VAS6350/4 from the left to the right side of the : VAS6350A
-- Turn off the : VAS6350/4 and reposition the calibration tool.
- When installed correctly, the vehicle electrical system voltage wire must be connected at the bottom left of the calibration device (as seen in direction of travel).
Dimension -a- is measured from the upper edge of the calibration device to the floor.
| Model | Q7 Basis, Before Product Improvement | SQ7/Q7 S-line, Before Product Improvement | Q7 from Product Improvement |
|---|---|---|---|
| Adjustment dimension height in mm dimension -a- | 681 | 675 | 700 |
-- The indicator on the base of the : VAS6350/4 must align with the adjustment dimension on the measuring scale -1- on the measuring field -arrow-.
| Model | Q7 Basis, Before Product Improvement | SQ7/Q7 S-line, Before Product Improvement | Q7 from Product Improvement |
|---|---|---|---|
| Right adjustment dimension read in mm on the measuring scale -1- | 800 | 817 | 860 |
-- Connect the : VAS6350/4 -1- to the vehicle electrical system voltage and switch it on at the voltage switch -2-.
- The green LED -4- must turn on.
-- Follow the instructions in the vehicle diagnostic tester display.
-- Switch off the ignition after successful calibration.
-- Disconnect the Vehicle Diagnostic Tester from the data link connector.
-- Disconnect the battery charger. Refer to BATTERY, CHARGING .