LEMON Manuals: Even more car manuals for everyone
Home >> Audi >> 2012 >> A7 >> Repair and Diagnosis >> Engine Performance >> Engine Control Systems >> 3.0L - Generic Scan Tool - Engine Code: CGXB (2 Of 2) >> St Generic Scan Tool >> Diagnosis And Testing >> Diagnostic Procedures >> Secondary Air Injection Solenoid Valve, Checking

Secondary Air Injection Solenoid Valve, Checking

Special tools and workshop equipment required 

Test requirements 

Test procedure 

-- Perform a preliminary check to verify the customers complaint. Refer to PRELIMINARY CHECK .

Start diagnosis 

NOTE:

Voltage is supplied to the Secondary Air Injection (AIR) Solenoid Valve -N112- from the Engine Component Power Supply Relay -J757-.

Procedure 

-- Disconnect the Secondary Air Injection (AIR) Solenoid Valve -N112- electrical harness connector -1-.

Fig 1: Installed Location: Secondary Air Injection Solenoid Valve And Intake Manifold Runner Control (IMRC) Valve -N316-
GWWA21-10366Courtesy of AUDI OF AMERICA, LLC

Checking internal resistance 

-- Using a multimeter, check the Secondary Air Injection (AIR) Solenoid Valve -N112- terminals 1 to 2 for resistance.

Fig 2: 2-Pin Electrical Connector & Terminals
GWWA28-0040Courtesy of AUDI OF AMERICA, LLC

Specified value: 25 to 35 Ω (at Approx. 20° C).

If the specified value was not obtained:

-- Replace the Secondary Air Injection (AIR) Solenoid Valve -N112- : Refer to appropriate Service Information.

If the specified value was obtained:

Checking voltage supply 

Switch the ignition ON.

-- Using a multimeter, check the Secondary Air Injection (AIR) Solenoid Valve -N112- electrical connector terminal 1 to Ground (GND) for voltage.

Fig 3: 2-Pin Electrical Connector & Terminals
GWWA28-0040Courtesy of AUDI OF AMERICA, LLC

Specified value: battery voltage.

Switch the ignition OFF.

If the specified value was not obtained:

-- Check the wiring from the Secondary Air Injection (AIR) Solenoid Valve -N112- electrical connector terminal 1 to the Engine Component Power Supply Relay -J757- terminal 8 for an open circuit.

-- Check the electrical harness connector for damage, corrosion, lose or broken terminals.

-- If necessary, repair the wiring connection.

If no malfunctions are found in the wiring:

Checking wiring 

If the manufacturers test box is being used. Perform the following step.

-- Install the test box.

If the manufacturers test box is not being used, perform the following step.

-- Remove the Engine Control Module -J623-. Refer to the appropriate Service Information.

-- Using a multimeter, check the Secondary Air Injection (AIR) Solenoid Valve -N112- electrical harness connector terminal 2 to the Engine Control Module -J623- electrical harness connector T94 terminal 49 for an open circuit.

Fig 4: 2-Pin Electrical Connector & Terminals
GWWA28-0040Courtesy of AUDI OF AMERICA, LLC
Secondary Air Injection (AIR) Solenoid Valve -N112- electrical harness connector terminal: Engine Control Module -J623- electrical connector T94 terminal:
2 49

Specified value: 1.5 Ω Max.

If the specification was not obtained:

-- Check the wiring for a short circuit to each other, Battery (+), and Ground (GND).

-- Check the electrical harness connector for damage, corrosion, lose or broken terminals.

-- If necessary, repair the faulty wiring connection.

If no malfunction is detected in the wiring:

-- Replace the Engine Control Module -J623-. Refer to appropriate Service Information.

Final procedures 

After repair work, the following work steps must be performed in the following sequence:

  1. Check the DTC memory. Refer to DIAGNOSTIC MODE 03 - READ DTC MEMORY .
  2. If necessary, erase the DTC memory. Refer to DIAGNOSTIC MODE 04 - ERASE DTC MEMORY .
  3. If the DTC memory was erased, generate readiness code. Refer to READINESS CODE .