LEMON Manuals: Even more car manuals for everyone
Home >> Audi >> 2012 >> A7 >> Repair and Diagnosis >> Engine Performance >> Engine Control Systems >> 3.0L - Generic Scan Tool - Engine Code: CGXB (2 Of 2) >> St Generic Scan Tool >> Diagnosis And Testing >> Diagnostic Procedures >> Evaporative Purge Regulator Valve, Checking

Evaporative Purge Regulator Valve, Checking

Observe all safety precautions: SAFETY PRECAUTIONS

View clean working conditions: CLEAN WORKING CONDITIONS

Use only gold-plated terminals when servicing any component with gold-plated electrical harness connector terminals.

For wiring diagrams, component locations, and connector views, Refer to the appropriate System Wiring Diagram.

Special tools and workshop equipment required 

Test requirements

NOTE:

Voltage for the Evaporative Emission (EVAP) Canister Purge Regulator Valve -N80- is supplied via the Engine Component Power Supply Relay -J757-.

Test procedure 

-- Perform a preliminary check to verify the customers complaint. Refer to PRELIMINARY CHECK .

Start diagnosis 

-- Remove the engine covers. Refer to the appropriate Service Information.

Fig 1: Engine Cover -1- And -2-
GWWA10-11070Courtesy of AUDI OF AMERICA, LLC

-- Disconnect the Evaporative Emission (EVAP) Canister Purge Regulator Valve -N80- electrical harness connector.

Fig 2: Evaporative Emission (EVAP) Canister Purge Regulator Valve -N80- Electrical Harness Connector
GWWA20-10964Courtesy of AUDI OF AMERICA, LLC

Checking internal resistance 

-- Using a Multimeter, check the Evaporative Emission (EVAP) Canister Purge Regulator Valve -N80- terminals 1 and 2 for resistance.

Specified value: 17.0 to 25.0 Ω.

If the specified value was Not obtained:

-- Replace the Evaporative Emission (EVAP) Canister Purge Regulator Valve -N80-. Refer to the appropriate Service Information.

-- Go to Final procedures.

If the specified value was obtained:

Checking voltage supply 

-- Using a Multimeter, check the Evaporative Emission (EVAP) Canister Purge Regulator Valve -N80- electrical harness connector terminal 1 to Ground (GND).

Evaporative Emission (EVAP) Canister Purge Regulator Valve - N80- electrical harness connector terminal: Measure to
1 Engine Ground (GND)

-- Start the Engine.

Specified value: battery voltage.

-- Switch the ignition OFF.

If the specified value was Not obtained:

-- Check for an open or grounded circuit between terminal 1 and the appropriate fuse. Refer to appropriate System Wiring Diagram for fuse positions.

-- Check the wiring connection for damage, corrosion, loose or broken terminals.

-- If necessary, repair the faulty wiring connection.

-- Repair the circuit and replace any open fuses.

-- Go to Final procedures.

If the specified value was obtained:

Checking wiring 

-- Remove the Engine Control Module - J623 -. Refer to the appropriate Service Information.

-- Using a Multimeter, check the Evaporative Emission (EVAP) Canister Purge Regulator Valve -N80- electrical harness connector to Engine Control Module -J623 - electrical harness connector T94.

Evaporative Emission (EVAP) Canister Purge Regulator Valve - N80- electrical harness connector terminal: Engine Control Module -J623- electrical connector T60 terminal:
2 75

Specified value: 1.5 Ω max.

If the specified value was not obtained:

-- Check the wiring connection for an open circuit, short circuit to Battery voltage or Ground

-- Check the electrical harness connector for damage, corrosion, loose or broken terminals.

-- If necessary, repair the faulty wiring connection.

-- Go to Final procedures.

If the specified value was obtained:

-- If no faults were found Replace the Engine Control Module - J623 -. Refer to appropriate Service Information.

Final procedures 

-- Reinstall the engine cover with air filter, if necessary. Refer to the appropriate Service Information.

-- After the repair work, the following work steps must be performed in the following sequence:

  1. Check the DTC memory. Refer to DIAGNOSTIC MODE 03 - READ DTC MEMORY .
  2. If necessary, erase the DTC memory. Refer to DIAGNOSTIC MODE 04 - ERASE DTC MEMORY .
  3. If the DTC memory was erased, generate readiness code. Refer to READINESS CODE .