LEMON Manuals: Even more car manuals for everyone
Home >> Audi >> 2012 >> A7 >> Repair and Diagnosis >> Engine Performance >> Engine Control Systems >> 3.0L - Generic Scan Tool - Engine Code: CGXB (2 Of 2) >> St Generic Scan Tool >> Diagnosis And Testing >> Diagnostic Procedures >> Camshaft Adjustment Valve 2, Checking

Camshaft Adjustment Valve 2, Checking

Observe all safety precautions: SAFETY PRECAUTIONS

View clean working conditions: CLEAN WORKING CONDITIONS

Use only gold-plated terminals when servicing any component with gold-plated electrical harness connector terminals.

For wiring diagrams, component locations, and connector views, Refer to the appropriate System Wiring Diagram.

Special tools and workshop equipment required 

Test requirements

Test procedure 

-- Perform a preliminary check to verify the customers complaint. Refer to PRELIMINARY CHECK .

Start diagnosis 

-- Remove the engine cover with air filter. Refer to appropriate Service Information.

Fig 1: Engine Cover -1- And -2-
GWWA10-11070Courtesy of AUDI OF AMERICA, LLC

-- Disconnect Camshaft Adjustment Valve 2 -N208- electrical harness connector -2-.

Fig 2: CMP Sensor And Exhaust Camshaft Control Valve Cylinder Bank 2 (Left)
GWWA15-10638Courtesy of AUDI OF AMERICA, LLC

-- Using a Multimeter, check the Camshaft Adjustment Valve 2 -N208- pins 1 & 2 for resistance.

Specified value: 5.0 to 8.0 Ω (at Approx. 20° C).

If the specified value was Not obtained:

-- Replace the Camshaft Adjustment Valve 1 - N205-. Refer to appropriate Service Information.

-- Go to Final procedures.

If the specified value was obtained:

Checking voltage 

-- Switch the ignition ON.

-- Using a Multimeter, Check the Camshaft Adjustment Valve 1 - N205- electrical harness connector terminal 1 to engine ground for voltage.

-- Switch the ignition OFF.

Specified value: battery voltage.

If the specified value was Not obtained:

-- Check the wiring connections for an open circuit, short circuit to Ground

-- Check the wiring connection for damage, corrosion, loose or broken terminals.

-- If necessary, repair the faulty wiring connection and replace any fuse if blown

-- Go to Final procedures.

If the specified value was obtained:

Checking wiring 

-- Remove the Engine Control Module -J623 -. Refer to appropriate Service Information.

-- Using a Multimeter, Check the Camshaft Adjustment Valve 1 -N205- electrical harness connector terminal 2 to the Engine Control Module electrical harness connector T60 terminal 39 for an open circuit.

Camshaft Adjustment Valve 1 - N205 - electrical harness connector terminal Engine Control Module electrical harness connector T60 terminal:
2 39

Specified value: 1.5 Ω Max.

If the specified value was Not obtained:

-- Check the wiring connection for an open circuit, short circuit to Battery voltage or Ground.

-- Check the wiring connection for damage, corrosion, loose or broken terminals.

-- If necessary, repair the faulty wiring connection.

-- Go to Final procedures.

If the specified value was obtained:

-- With the Engine Control Module Connectors still unplugged - J623 -. Refer to appropriate Service Information.

-- Use a Multimeter, Check the Camshaft Adjustment Valve 1 -N205- electrical harness connector terminal 2 to engine ground for continuity

If Specified value is 1.5 Ω or less.

-- Check the wiring connection for a short circuit to Engine Ground.

-- If necessary, repair the faulty wiring or connection, If no faults were found Replace the Engine Control Module - J623 -. Refer to appropriate Service Information.

Final procedures 

-- Reinstall the engine cover with air filter, if necessary. Refer to the appropriate Service Information.

-- After the repair work, the following work steps must be performed in the following sequence:

  1. Check the DTC memory. Refer to DIAGNOSTIC MODE 03 - READ DTC MEMORY .
  2. If necessary, erase the DTC memory. Refer to DIAGNOSTIC MODE 04 - ERASE DTC MEMORY .
  3. If the DTC memory was erased, generate readiness code. Refer to READINESS CODE .