Camshaft Adjustment Valve 1, Checking
Observe all safety precautions: SAFETY PRECAUTIONS .
View clean working conditions: CLEAN WORKING CONDITIONS .
Use only gold-plated terminals when servicing any component with gold-plated electrical harness connector terminals.
For wiring diagrams, component locations, and connector views, Refer to the appropriate System Wiring Diagram.
Special tools and workshop equipment required
- Multimeter
- Appropriate System Wiring diagram
Test requirements
- The Camshaft Adjustment Valve 1 -N205- fuse OK.
- Motronic Engine Control Module Power Supply Relay J271 OK.
- Battery voltage at least 12.5 volts.
- All electrical consumers such as, lights and rear window defroster, switched OFF.
- Vehicles with automatic transmission, shift selector lever into position "P" or "N".
- A/C switched OFF.
- Ground (GND) connections between engine/transmission/chassis OK.
- Ignition switched OFF.
Test procedure
-- Perform a preliminary check to verify the customers complaint. Refer to PRELIMINARY CHECK .
Start diagnosis
-- Remove the engine cover with air filter. Refer to appropriate Service Information.
-- Disconnect Camshaft Adjustment Valve 1 - N205- electrical harness connector -1-.
-- Using a Multimeter, check the Camshaft Adjustment Valve 1 -N205- pins 1 & 2 for resistance.
Specified value: 5.0 to 8.0 Ω (at Approx. 20° C)
If the specified value was Not obtained:
-- Replace the Camshaft Adjustment Valve 1 - N205-. Refer to appropriate Service Information.
-- Go to Final procedures.
If the specified value was obtained:
Checking voltage
-- Switch the ignition ON.
-- Using a Multimeter, Check the Camshaft Adjustment Valve 1 - N205- electrical harness connector terminal 1 to engine ground for voltage.
-- Switch the ignition OFF.
Specified value: battery voltage.
If the specified value was Not obtained:
-- Check the wiring connections for an open circuit, short circuit to Ground
-- Check the wiring connection for damage, corrosion, loose or broken terminals.
-- If necessary, repair the faulty wiring connection and replace any fuse if blown
-- Go to Final procedures.
If the specified value was obtained:
Checking wiring
-- Remove the Engine Control Module -J623 -. Refer to appropriate Service Information.
-- Using a Multimeter, Check the Camshaft Adjustment Valve 1 -N205- electrical harness connector terminal 2 to the Engine Control Module electrical harness connector T60 terminal 54 for an open circuit.
| Camshaft Adjustment Valve 1 - N205 - electrical harness connector terminal | Engine Control Module electrical harness connector T60 terminal |
|---|---|
| 2 | 54 |
Specified value: 1.5 Ω Max.
If the specified value was Not obtained:
-- Check the wiring connection for an open circuit, short circuit to Battery voltage or Ground
-- Check the wiring connection for damage, corrosion, loose or broken terminals.
-- If necessary, repair the faulty wiring connection.
-- Go to Final procedures.
If the specified value was obtained:
-- With the Engine Control Module Connectors still unplugged - J623 -. Refer to appropriate Service Information.
-- Use a Multimeter, Check the Camshaft Adjustment Valve 1 -N205- electrical harness connector terminal 2 to engine ground for continuity
If Specified value is 1.5 Ω or less
-- Check the wiring connection for a short circuit to Engine Ground
-- If necessary, repair the faulty wiring or connection, If no faults were found Replace the Engine Control Module - J623 -. Refer to appropriate Service Information.
Final procedures
-- Reinstall the engine cover with air filter, if necessary. Refer to the appropriate Service Information.
-- After the repair work, the following work steps must be performed in the following sequence:
- Check the DTC memory. Refer to DIAGNOSTIC MODE 03 - READ DTC MEMORY .
- If necessary, erase the DTC memory. Refer to DIAGNOSTIC MODE 04 - ERASE DTC MEMORY .
- If the DTC memory was erased, generate readiness code. Refer to READINESS CODE .