Seat Memory Does Not Work (GROUP 72, NO. 13-09)
Publication date: 2013-09-25Reference number: GROUP 72, NO. 13-09
Supersedes refnos: 2035357
SEAT MEMORY DOES NOT WORK
TECHNICAL SERVICE BULLETIN
| AUDI: | A4 2012 - 2014; A5, A6, A7, A8, Q5, Q7 2011 - 2014 |
| GROUP: | 72 - Seat - Frame, Spring Core |
72 13 09 2035357/1 September 25, 2013.
| Model(s) | Year | VIN Range | Vehicle-Specific Equipment |
|---|---|---|---|
| A4 | 2012 - 2014 | All | Not Applicable |
| A5, A6, A7, A8, Q5, Q7 | 2011 - 2014 | All | Not Applicable |
CONDITION
- Seat memory function does not work.
- One of the following DTCs is stored:
- DTC 3FDB (Control Unit Faulty) in the seat adjustment driver side module, J136 (address word 36)
- DTC 3FDB (Control Unit Faulty) in the seat adjustment passenger side module, J521 (address word 06)
TECHNICAL BACKGROUND
In the event of a voltage fluctuation in the vehicle power system, the software of the seat adjustment module fails.
PRODUCTION SOLUTION
Software update for existing vehicles. Production solution is in preparation.
SERVICE
- Install approved vehicle battery maintainer on vehicle (Figure 1).
- The software must be updated with Guided Fault Finding (GFF). Self-diagnosis or "flash" cannot be used.
Note that in certain cases (such as with Q7), SVM will not code the seat control module.
Before performing the update, record the coding of the module by right-clicking on the control module in ODIS, then selecting "Control module ODB" (Figure 2).
- Perform Identification (Figure 3).
- Make note of the module coding (Figure 4). The coding should be double-checked after the control module update.
- To perform SVM in GFF, select the "Special functions" tab, then "SVM - Code input" (Figure 5).
- Enter SVM code 36A001 (Figure 6). Refer to the SVM table at the bottom of this section for software information.
- When prompted, select "Automatic sequence (Audi Flashing)" (Figure 7).
- Follow the instructions on the tester to complete the control module update (Figure 8).
- After updating the control module, verify that the coding is correct.
- Perform basic settings of the front seats. Each seat must run the full length of travel, forward, backward, up, and down for each motor (Figure 9). The number of adjustments will vary depending on vehicle options.
- If necessary, perform the additional seat and seatbelt basic settings shown in the MMI (varies by vehicle) (Figure 10).
When the seat is fully adapted and properly coded, the "SET" button will light up when pressed (Figure 11).
- Recheck the DTC memory (Figure 12). If all work has been performed properly, the fault will not return.
If the fault does return, run the affected adjustment to its end stops and recheck the fault.
- After all work is complete, end Diagnosis (Figure 13).
| Model | Old Software Part Number | Old Software Version | New Software Part Number | New Software Version (or higher) | SVM Action Code |
|---|---|---|---|---|---|
| A4/S4/allroad, A5/S5/RS5, A5/S5/RS5 cab, Q5/Q5 hybrid/SQ5, A6/S6, A7/S7/RS7, A8/A8L/S8, Q7 | 8K0959760D | 76 | 8K0959760D | 77 | 36A001 |
| 8K0959760E | 76 | 8K0959760E | 77 | ||
| 8T0959760E | 76 | 8T0959760E | 77 | ||
| 8T0959760F | 76 | 8T0959760F | 77 | ||
| 8R0959760D | 76 | 8R0959760D | 77 | ||
| 8R0959760E | 76 | 8R0959760E | 77 | ||
| 4H0959760H | 163 | 4H0959760H | 164 | ||
| 4H0959760D | 153 | 4H0959760D | 156 | ||
| 4H0959760E | 153 | 4H0959760E | 156 | ||
| 4H0959760F | 153 | 4H0959760F | 156 | ||
| 4H0959860 | 155 | 4H0959860 | 158 | ||
| 4H0959860A | 155 | 4H0959860A | 158 | ||
| 4G8959760 | 154 | 4G8959760 | 157 | ||
| 4G8959760A | 154 | 4G8959760A | 157 | ||
| 4G8959760B | 154 | 4G8959760B | 157 | ||
| 4G8959760C | 154 | 4G8959760C | 157 | ||
| 4F0959760D | 64 | 4F0959760D | 65 |
WARRANTY
| Claim Type: | Use applicable claim type. If vehicle is outside any warranty, this Technical Service Bulletin is informational only. | ||
| Service Number: | 7293 | ||
| Damage Code: | 0039 | ||
| Labor Operations: | Charge battery | 2706 8950 10 | TU |
| Diagnostic Time: | GFF | 0150 0000 | Time stated on diagnostic protocol (Max 100 TU) |
| Road test prior to service procedure | No allowance | 0 TU | |
| Road test after service procedure | No allowance | 0 TU | |
| Technical diagnosis at dealer's discretion (Refer to Section 2.2.1.2 and Audi Warranty Online for DADP allowance details) |
|||
| Claim Comment: | As per TSB #2035357/1 | ||
All warranty claims submitted for payment must be in accordance with the Audi Warranty Policies and Procedures Manual. Claims are subject to review or audit by Audi Warranty.
REQUIRED PARTS AND TOOLS
Approved battery charger
ADDITIONAL INFORMATION
The following Technical Service Bulletin may be necessary to complete this procedure:
- TSB 2011732 : Software Version Management (SVM), operating instructions .
All part and service references provided in this TSB (2035357) are subject to change and/or removal. Always check with your Parts Dept. and service manuals for the latest information.