LEMON Manuals: Even more car manuals for everyone
Home >> Audi >> 1983 >> 5000 Base >> Repair and Diagnosis >> Quick Lookups >> Technical Bulletins >> Technical Service Bulletins >> Cruise Control Systems >> Cruise Control Repairing/Troubleshooting (GROUP 22, NO. 82-01)

Cruise Control Repairing/Troubleshooting (GROUP 22, NO. 82-01)

Publication date: 1983-02-23
Reference number: GROUP 22, NO. 82-01

CRUISE CONTROL REPAIRING/TROUBLESHOOTING

CRUISE CONTROL REPAIRING/TROUBLESHOOTING

TECHNICAL SERVICE BULLETIN

Reference Number(s): GROUP 22, NO. 82-01

CRUISE CONTROL - REPAIRING/TROUBLESHOOTING

Model(s): 1981-on Audi 5000 (All)

Group: 22

Bulletin No.: 82-01

Date: December 17, 1982 (revised February 23, 1983)

NOTE: The bulletin supersedes Suppl. No. 70 of November 1980.

CRUISE CONTROL SYSTEM GENERAL LAYOUT

For cruise control system general layout, refer to Fig 1 .

NOTE: For cruise control current-flow diagram, refer to Fig 2 .

CONTROL UNIT, REMOVING/INSTALLING

- Remove cover below instrument panel on left.

- Remove screw. See Fig 3 , (arrow).

RELAY, REMOVING/INSTALLING

- Remove cover below instrument panel on left.

- Remove screw. See Fig 4 , (arrow).

CLUTCH/BREAK PEDAL VENT VALVE, REMOVING/INSTALLING

- Remove cover below instrument panel on left.

- Loosen locknut on clutch pedal vent valve. See Fig 5 , (arrow 1).

- Loosen locknut on brake pedal vent valve. See Fig 5 , arrow 2).

- Remove hose and vent valve.

VENT VALVES, ADJUSTING

- Install vent valve shown in Fig. Fig 6 , and turn until there is no resistance (zero ohms) between terminals, measured with ohmmeter.

- Tighten locknut to 3.5 N.m (3 ft-lbs.).

- Pressing the brake pedal opens the contacts, thus interrupting the ground to the control unit. This action causes the control unit to shut off electrically until the resume button is pressed.

VACUUM PUMP, REMOVING/INSTALLING

- Remove cover for water tray.

- Remove screws. See Fig 7 , (arrows).

SERVO UNIT, REMOVING/INSTALLING

- Unhook linkage.

- Remove nut. See Fig 8 , (arrow).

SERVO UNIT LINKAGE, CIS ENGINE, ADJUSTING

- Set throttle at idle position.

- Adjust linkage (1) until play is felt at (2). See Fig 9 .

SERVO UNIT LINKAGE, DIESEL ENGINE, ADJUSTING

- Set throttle at idle position.

- Loosen nut on ball joint.

- Adjust linkage (1) until play is felt at (2). See Fig 10 .

CRUISE CONTROL, TROUBLESHOOTING

NOTE: See Fig 12 and Fig 13 .

Check these first:

NOTE: If while checking, an inoperative component is found, check wiring from control unit plug to component.
Fig 1: Cruise Control System General Layout
G93B59692
Fig 2: Current Flow Diagram (Cruise Control System)
G93C59693
Fig 3: Control Unit Mounting Screw Location
G93D59694
Fig 4: Relay Location
G93E59695
Fig 5: Clutch/Brake Pedal Vent Valves Locations
G93F59696
Fig 6: Clutch/Brake Pedal Vent Valve
G93G59697
Fig 7: Vacuum Pump Mounting Screw Locations
G93H59698
Fig 8: Servo Unit Mounting Nut Location
G93B59577
Fig 9: Servo Unit Linkage Adjustment (CIS Engine)
G93C59578
Fig 10: Servo Unit Linkage Adjustment (Diesel Engine)
G93I59699
Fig 11: Control Unit Connector For Cruise Control
G93G59580
Fig 12: CRUISE CONTROL TROUBLESHOOTING (1 OF 2)
GB0043868
Fig 13: CRUISE CONTROL TROUBLESHOOTING (2OF 2)
GB0043869