LEMON Manuals: Even more car manuals for everyone
Home >> Alfa Romeo >> 2019 >> 4C >> Repair and Diagnosis >> Engine Mechanical >> Fuel System >> Fuel Delivery >> Rail, Fuel >> Removal And Installation

Removal And Installation

REMOVAL 

  1. Raise and support the vehicle. Refer to HOISTING, STANDARD PROCEDURE .
  2. Disconnect the negative battery terminal.
  3. Remove the front belly pan. Refer to BELLY PAN, FRONT, REMOVAL AND INSTALLATION .
  4. Remove the engine cover. Refer to COVER, ENGINE, REMOVAL AND INSTALLATION .
  5. Remove the engine bellypan. Refer to BELLY PAN, ENGINE, REMOVAL AND INSTALLATION .
  6. Drain the engine coolant. Refer to STANDARD PROCEDURE .
  7. Remove the Powertrain Control Module. Refer to MODULE, POWERTRAIN CONTROL (PCM), REMOVAL AND INSTALLATION .
  8. Remove the intake manifold

    Refer to MANIFOLD, INTAKE, REMOVAL AND INSTALLATION .

  9. Remove the HIGH PRESSURE PIPE FROM PRESSURE PUMP TO SINGLE FUEL MANIFOLD PIPE. Refer to LINES, FUEL, REMOVAL AND INSTALLATION .
  10. Remove the alternator guard. Refer to GAURD, GENERATOR, REMOVAL AND INSTALLATION .
    GC0167790Courtesy of CHRYSLER GROUP, LLC
  11. Detach the fuel pressure sensor electrical connection.
    GC0167469Courtesy of CHRYSLER GROUP, LLC
  12. Undo and remove the air intake chamber fixing stud bolt.
    GC0167789Courtesy of CHRYSLER GROUP, LLC
  13. Undo the fixing screws (1a) and partly remove the single manifold pipe (1b) complete with injectors.
    GC0167793Courtesy of CHRYSLER GROUP, LLC
  14. Detach the electrical connections for the injectors.
    GC0167941Courtesy of CHRYSLER GROUP, LLC
  15. Remove the single fuel manifold pipe from its housing.
  16. Undo the fuel pressure sensor and remove it.
    GC0167468Courtesy of CHRYSLER GROUP, LLC
  17. If required, press to remove the injectors with O-rings.

INSTALLATION 

  1. Place the fuel pressure sensor in its housing and tighten it.
    GC0167586Courtesy of CHRYSLER GROUP, LLC
    NOTE:

    To prevent engine malfunction, pay the utmost attention when refitting injectors, avoiding damage to the Teflon ring.

  2. Press fit the injectors with new O-rings.
  3. Check the deterioration of the Teflon ring: if it is worn, proceed to replace the injector.
    GC0167942Courtesy of CHRYSLER GROUP, LLC
  4. Fit the complete single fuel manifold pipe (1a) in position and tighten the fixing screws (1b).
    Component Fixing Ø Value (daNm)
    Single fuel manifold pipe Screw M8x1.25x40 2.0 ÷ 2.4
  5. Connect the electrical connections for the injectors.
  6. Connect the electrical connection for the fuel pressure sensor.
  7. Tighten the air intake chamber fixing stud bolt.
  8. Install the alternator guard. Refer to GAURD, GENERATOR, REMOVAL AND INSTALLATION .
  9. Install the HIGH PRESSURE PIPE FROM PRESSURE PUMP TO SINGLE FUEL MANIFOLD PIPE. Refer to LINES, FUEL, REMOVAL AND INSTALLATION .
  10. Install the intake manifold

    Refer to MANIFOLD, INTAKE, REMOVAL AND INSTALLATION .

  11. Install the Powertrain Control Module. Refer to MODULE, POWERTRAIN CONTROL (PCM), REMOVAL AND INSTALLATION .
  12. Refill the engine coolant. Refer to STANDARD PROCEDURE .
  13. Install the engine bellypan. Refer to BELLY PAN, ENGINE, REMOVAL AND INSTALLATION .
  14. Install the front belly pan. Refer to BELLY PAN, FRONT, REMOVAL AND INSTALLATION .
  15. Install the engine cover. Refer to COVER, ENGINE, REMOVAL AND INSTALLATION .
  16. Connect the negative battery terminal.
  17. Remove the vehicle from the hoist.