LEMON Manuals: Even more car manuals for everyone
Home >> Acura >> 2013 >> TL Base >> Repair and Diagnosis >> Engine Mechanical >> Cooling Fan >> Fan Controls >> Radiator Fan High Speed Circuit Troubleshooting

Radiator Fan High Speed Circuit Troubleshooting

NOTE: Information marked with an asterisk (*1) applies to without SH-AWD and (*2) applies to with SH-AWD.
  1. Check the No. 3-5 (30 A) (*1), (40 A) (*2) fuse, the No. 14 (15 A) fuse, and the No. 21 (7.5 A) fuse in the under-hood fuse/relay box, and the No. 16(7.5 A) fuse in the driver's under-dash fuse/relay box.

    Are the fuse(s) OK? 

    YES  - Reinstall the fuses, then go to step 2.

    NO  - Replace the fuse(s) and recheck. If the fuse(s) blow again, repair the short to ground on the No. 3-5 (30A) (*1), (40 A) (*2) fuse, the No. 14 (15A) fuse, the No. 21 (7.5A) fuse, and the No. 16 (7.5A) fuse circuit.

  2. Disconnect and remove the relay circuit board from the under-hood fuse/relay box, and test it (see FIVE-TERMINAL TYPE ).

    Is the relay circuit board OK? 

    YES  - Go to step 3.

    NO  - Replace the relay circuit board (see REMOVAL AND INSTALLATION ).

  3. Measure the voltage between under-hood fuse/relay box connector terminal C3 and body ground.
    Fig 1: Measuring Voltage Between Under-Hood Fuse/Relay Box Connector Terminal C3 And Body Ground
    G08067245Courtesy of AMERICAN HONDA MOTOR CO., INC.

    Is there battery voltage? 

    YES  - Go to step 4.

    NO  - Replace the under-hood fuse/relay box (see REMOVAL AND INSTALLATION ).

  4. Connect under-hood fuse/relay box connector terminals C1 and C3 with a jumper wire.
    Fig 2: Connecting Under-Hood Fuse/Relay Box Connector Terminals C1 And C3 With Jumper Wire
    G08067246Courtesy of AMERICAN HONDA MOTOR CO., INC.

    Does the radiator fan run at high speed? 

    YES  - Go to step  8.

    NO  - Go to step 5.

  5. Disconnect the radiator fan motor 2P connector, then test the fan motor (see FAN MOTOR TEST ).

    Is the fan motor OK? 

    YES  - Go to step 6.

    NO  - Replace the radiator fan motor (see FAN, FAN MOTOR, AND SHROUD REMOVAL AND INSTALLATION ).

  6. Check for continuity between under-hood fuse/relay box connector terminal C1 and radiator fan motor 2P connector terminal No. 2.
    Fig 3: Checking Continuity Between Under-Hood Fuse/Relay Box Connector And Radiator Fan Motor 2P Connector
    G08067247Courtesy of AMERICAN HONDA MOTOR CO., INC.

    Is there continuity? 

    YES  - Go to step 7.

    NO  - Repair an open in the wire between under-hood fuse/relay box connector terminal C1 and radiator fan motor 2P connector terminal No. 2.

  7. Check for continuity between radiator fan motor 2P connector terminal No. 1 and body ground.
    Fig 4: Checking Continuity Between Radiator Fan Motor 2P Connector Terminal No. 1 And Body Ground
    G08067248Courtesy of AMERICAN HONDA MOTOR CO., INC.

    Is there continuity? 

    YES  - Check for poor connections or loose terminals at the radiator fan motor and body ground G302.

    NO  - Repair an open in the wire between radiator fan motor 2P connector terminal No. 1 and body ground.

  8. Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode.
  9. Measure the voltage between under-hood fuse/relay box connector terminal B8 and body ground.
    Fig 5: Measuring Voltage Between Under-Hood Fuse/Relay Box Connector Terminal B8 And Body Ground
    G08067249Courtesy of AMERICAN HONDA MOTOR CO., INC.

    Is there battery voltage? 

    YES  - Go to step 10.

    NO  - Repair an open in the wire between driver's under-dash fuse/relay box connector terminal F26 and under-hood fuse/relay box connector terminal B8.

  10. Measure the voltage between under-hood fuse/relay box connector terminal B9 and body ground.
    Fig 6: Measuring Voltage Between Under-Hood Fuse/Relay Box Connector Terminal B9 And Body Ground
    G08067250Courtesy of AMERICAN HONDA MOTOR CO., INC.

    Is there battery voltage? 

    YES  - Go to step 11.

    NO  - Check the PGM-FI subrelay. If the relay is OK, replace the under-hood fuse/relay box (see REMOVAL AND INSTALLATION ).

  11. Turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.
  12. Connect the HDS to the DLC (see HOW TO USE THE HDS (HONDA DIAGNOSTIC SYSTEM) ).
  13. Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode.
  14. Make sure the HDS communicates with the vehicle and the ECM/PCM. If it does not communicate, troubleshoot the DLC circuit (see DLC CIRCUIT TROUBLESHOOTING ).
  15. Jump the SCS line with the HDS, then turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.
    NOTE: This step must be done to protect the ECM/PCM from damage.
  16. Disconnect ECM/PCM connector A (49P).
  17. Check for continuity between ECM/PCM connector terminal A5 and under-hood fuse/relay box connector terminal B10.
    Fig 7: Checking Continuity Between ECM/PCM Connector Terminal A5 And Under-Hood Fuse/Relay Box Connector Terminal B10
    G08067251Courtesy of AMERICAN HONDA MOTOR CO., INC.

    Is there continuity? 

    YES  - Update the ECM/PCM if it does not have the latest software (see ECM/PCM UPDATE ), or substitute a known-good ECM/PCM (see SUBSTITUTING THE ECM/PCM ), then recheck. If the symptom/indication goes away with a known-good ECM/PCM, replace the original ECM/PCM (see ECM/PCM REPLACEMENT ).

    NO  - Repair an open in the wire between under-hood fuse/relay box connector terminal B10 and ECM/PCM connector terminal A5.