Moonroof Control Unit Input Test
NOTE:
- If the moonroof works OK manually, but will not work in AUTO, or reverses frequently (obstacle detection), reset the moonroof (see RESETTING THE MOONROOF CONTROL UNIT ) before proceeding with the input test.
- SRS components are located in this area. Review the SRS component locations (see COMPONENT LOCATION INDEX ), and precautions and procedures (see PRECAUTIONS AND PROCEDURES ) before doing repairs or servicing.
- Turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.
- Remove the headliner (see HEADLINER REMOVAL/INSTALLATION ).
- Disconnect the 14P connector (A) from the moonroof control unit/motor (B).
- Inspect the connector and socket terminals to be sure they are all making good contact.
- If the terminals are bent, loose, or corroded, repair them as necessary, and recheck the system.
- If the terminals look OK, go to step 5.
- With the moonroof control unit/motor 14P connector still disconnected, do the following input tests:
- If any test indicates a problem, find and correct the cause, then recheck the system.
- If the input test proves OK, go to step 6.
Cavity Wire Test condition Test: Desired result Possible cause if desired result is not obtained 11 PNK Disconnect the power window master switch 37P connector and the front passenger's power window switch 37P connector Check for continuity between moonroof switch 14P connector terminal No. 11 and power window master switch 37P connector terminal No. 27: There should be continuity. An open in the UART wire Check for continuity to ground: There should be no continuity. A short to ground in the UART wire - Reconnect the connector to the control unit, and do the following input tests:
- If any test indicates a problem, find and correct the cause, then recheck the system.
- If all the input tests prove OK, go to step 7.
Cavity Wire Test condition Test: Desired result Possible cause if desired result is not obtained 7 WHT Under all conditions Measure the voltage to ground: There should be battery voltage. - Blown No. 20 (20 A) fuse in the driver's under-dash fuse/relay box
- An open or high resistance in the wire
8 BLK In all ignition switch positions or all power modes Measure the voltage to ground: There should be less than 0.2 V. - Poor ground(G403)
- An open or high resistance in the ground wire
2 BLU Ignition switch to ON (II), or power mode ON, moonroof switch in CLOSE position Measure the voltage to ground: There should be less than 0.2 V. - Faulty moonroof switch
- Poor ground (G401) or an open in the ground wire
- An open or high resistance in the wire
Ignition switch to ON (II), or power mode ON, moonroof switch released Measure the voltage to ground: There should be battery voltage. - Blown No. 20 (20 A) fuse in the driver's under-dash fuse/relay box
- Faulty driver's under-dash fuse/relay box
- Faulty moonroof switch
- A short to ground in the wire
3 LT GRN Ignition switch to ON (II), or power mode ON, moonroof switch in TILT position Measure the voltage to ground: There should be less than 0.2 V. - Faulty moonroof switch
- Poor ground (G401) or an open in the ground wire
- An open or high resistance in the wire
Ignition switch to ON (II), or power mode ON, moonroof switch released Measure the voltage to ground: There should be battery voltage. - Blown No. 20 (20 A) fuse in the driver's under-dash fuse/relay box
- Faulty driver's under-dash fuse/relay box
- Faulty moonroof switch
- A short to ground in the wire
4 LT BLU Ignition switch to ON (II), or power mode ON, moonroof switch in OPEN position Measure the voltage to ground: There should be less than 0.2 V. - Faulty moonroof switch
- Poor ground (G401) or an open in the ground wire
- An open or high resistance in the wire
Ignition switch to ON (II), or power mode ON, moonroof switch released Measure the voltage to ground: There should be battery voltage. - Blown No. 20 (20 A) fuse in the driver's under-dash fuse/relay box
- Faulty driver's under-dash fuse/relay box
- Faulty moonroof switch
- A short to ground in the wire
9 PUR Ignition switch to ON (II), or power mode ON, moonroof switch in AUTO OPEN or AUTO CLOSE position Measure the voltage to ground: There should be less than 0.2 V. - Faulty moonroof switch
- Poor ground (G401) or an open in the ground wire
- An open or high resistance in the wire
Ignition switch to ON (II), or power mode ON, moonroof switch released Measure the voltage to ground: There should be battery voltage. - Blown No. 20 (20 A) fuse in the driver's under-dash fuse/relay box
- Faulty driver's under-dash fuse/relay box
- Faulty moonroof switch
- A short to ground in the wire
- If all the input tests are OK and multiple failures are found, replace the moonroof control unit/motor assembly (see MOTOR REPLACEMENT ). If the problem is related to the key-off operation, go to the driver's MICU input test (see CONTROL UNIT INPUT TEST ), and power window master switch input test (see POWER WINDOW MASTER SWITCH INPUT TEST ).