LEMON Manuals: Even more car manuals for everyone

Steering Gearbox Removal and Installation: Removal

  1. Do the battery terminal disconnection procedure (see BATTERY TERMINAL DISCONNECTION AND RECONNECTION )
  2. Raise the vehicle on a lift, and support it with safety stands in the proper locations (see LIFT AND SUPPORT POINTS )
  3. Remove the front wheels
  4. Remove the driver's airbag (see DRIVER'S AIRBAG REPLACEMENT ) and the steering wheel (see STEERING WHEEL REMOVAL )
  5. Remove the steering joint cover (A)
    Fig 1: Identifying Steering Joint Cover
    G05987649Courtesy of AMERICAN HONDA MOTOR CO., INC.
  6. Loosen the upper steering joint bolt (A), and remove the lower steering joint bolt (B) Disconnect the steering joint (C) by sliding the steering joint into the column Tighten the upper steering joint bolt to hold the steering wheel Do not disconnect the steering joint from the column shaft (D)
    Fig 2: Identifying Upper Steering Joint Bolt, Lower Steering Joint Bolt, Steering Joint And Column Shaft
    G05987650Courtesy of AMERICAN HONDA MOTOR CO., INC.
  7. Remove the center guide (A) (if equipped) from the top of the pinion shaft (B), and discard it The center guide is for factory assembly use only
    Fig 3: Identifying Center Guide And Pinion Shaft
    G05987651Courtesy of AMERICAN HONDA MOTOR CO., INC.
  8. Apply vinyl tape to the splines on the pinion shaft
  9. Disconnect the support struts from both sides of the pivot ball (bolted to the hood) Secure the hood in a vertical position Remove the right side pivot ball and install it into the lower threaded hole, then reattach the support strut
    NOTE: Do not attempt to close the hood with the support strut in the vertical position, as it will damage the support strut and hood
    Fig 4: Identifying Support Struts Vertical Positions
    G05987652Courtesy of AMERICAN HONDA MOTOR CO., INC.
  10. Remove the left and right engine compartment covers, the strut brace cover, and the front bulkhead cover (see FRONT BULKHEAD BRACE COVER REPLACEMENT ), then remove the cowl cover (see FRONT BULKHEAD BRACE COVER REPLACEMENT )
  11. Remove the strut brace (see FRAME BRACE REPLACEMENT )
  12. Remove the cotter pin (A) from the tie-rod end ball joint, then remove the nut (B) on both sides
    Fig 5: Identifying Cotter Pin And Nut
    G05987653Courtesy of AMERICAN HONDA MOTOR CO., INC.
  13. Disconnect the tie-rod end ball joint from the knuckle using the ball joint thread protector and the ball joint remover on both sides (see BALL JOINT BOOT INSPECTION/REPLACEMENT )
  14. Remove the P/S heat shield (A)
    Fig 6: Identifying P/S Heat Shield
    G05987654Courtesy of AMERICAN HONDA MOTOR CO., INC.
  15. On the vehicle side, disconnect the EPS subharness 12P connector (A) and the EPS subharness 3P connector (B) by pushing the lock (C) and pulling up the lever (D) Wrap the connectors with vinyl tape to avoid contamination from grease or water
    Fig 7: Identifying EPS Subharness 12P Connector, EPS Subharness 3P Connector, Lock And Lever
    G05987655Courtesy of AMERICAN HONDA MOTOR CO., INC.
  16. On the steering gearbox side, remove the EPS subharness 12P connector (E), the EPS subharness 3P connector (F), and the harness clip (G) from the harness bracket (H)
  17. Remove the harness clips (A), then remove the heat shield bracket (B) from the steering gearbox
    Fig 8: Identifying Harness Clips And Heat Shield Bracket
    G05987656Courtesy of AMERICAN HONDA MOTOR CO., INC.
  18. Remove the steering gearbox mounting bolts (A) and washers (B) from the steering gearbox
    Fig 9: Identifying Steering Gearbox Mounting Bolts And Washers
    G05987657Courtesy of AMERICAN HONDA MOTOR CO., INC.
  19. Remove the connector bracket from the front cylinder head, use the bracket bolt hole to attach the engine hanger balance bar front arm
    Fig 10: Identifying Connector Bracket And Front Cylinder Head
    G05987658Courtesy of AMERICAN HONDA MOTOR CO., INC.
  20. Disconnect the vacuum hose (A), and remove the harness clamp (B), then remove the engine mount control solenoid valve bracket from the rear cylinder head, use the bracket bolt hole to attach the 2008 V6 attachment arm (SIL02C000033)
    Fig 11: Identifying Vacuum Hose And Harness Clamp
    G05987659Courtesy of AMERICAN HONDA MOTOR CO., INC.
  21. Lift and support the engine with the engine support hanger (AAR-T1256) and the engine hanger balance bar (VSB02C000019) Attach the front arm (A) to the front cylinder head with a spacer (B) and a 10 x 1 25 mm bolt (C) Remove the rear arm from the engine hanger balance bar, and install the 2008 V6 attachment arm (SIL02C000033), then attach the 2008 V6 attachment arm (D) to the rear cylinder head with the 8 x 1 25 mm bolt (E)
    Fig 12: Identifying Engine Support Hanger (AAR-T1256) And Engine Hanger Balance Bar (VSB02C000019)
    G05987660Courtesy of AMERICAN HONDA MOTOR CO., INC.
  22. Support the engine with a jack and a wood block under the oil pan
  23. Remove the rear engine mount stop (A) and the heat shield (B), then remove the rear engine mount (C)
    Fig 13: Identifying Rear Engine Mount Stop, Heat Shield And Rear Engine Mount
    G05987661Courtesy of AMERICAN HONDA MOTOR CO., INC.
  24. Disconnect the vacuum hose (D)
  25. Remove the EPS subharness holder (A), then remove the rear engine mount base (B)
    Fig 14: Identifying EPS Subharness Holder And Rear Engine Mount Base
    G05987662Courtesy of AMERICAN HONDA MOTOR CO., INC.
  26. Remove the front engine mount stop (A) and the vacuum hose bracket (B), then remove the front engine mount bolt (C)
    Fig 15: Identifying Front Engine Mount Stop, Vacuum Hose Bracket And Front Engine Mount Bolt
    G05987663Courtesy of AMERICAN HONDA MOTOR CO., INC.
  27. Raise the vehicle on a lift
  28. Remove the front splash shield (see FRONT SPLASH SHIELD REPLACEMENT )
  29. Remove the front subframe stiffener (A)
    Fig 16: Identifying Front Subframe Stiffener
    G05987664Courtesy of AMERICAN HONDA MOTOR CO., INC.
  30. Remove the exhaust pipe A
  31. With SH-AWD Remove the propeller shaft (see PROPELLER SHAFT REMOVAL )
  32. Remove the cotter pin (A) from the knuckle ball joint, then remove the castle nut (B)
    Fig 17: Identifying Cotter Pin And Castle Nut
    G05987665Courtesy of AMERICAN HONDA MOTOR CO., INC.
  33. Disconnect the knuckle ball joint from the lower arm using the ball joint remover (see BALL JOINT BOOT INSPECTION/REPLACEMENT )
    NOTE:
    • Be careful not to damage the ball joint boot when installing the remover
    • Do not force or hammer on the lower arm, or pry between the lower arm and the knuckle You could damage the ball joint
  34. Remove the damper fork mounting nut (A) and mounting bolt (B)
    Fig 18: Identifying Damper Fork Mounting Nut And Mounting Bolt
    G05987666Courtesy of AMERICAN HONDA MOTOR CO., INC.
  35. Remove the front subframe middle mounts (A)
    Fig 19: Identifying Front Subframe Middle Mounts
    G05987667Courtesy of AMERICAN HONDA MOTOR CO., INC.
  36. Remove the lower transmission mount nuts (A)
    Fig 20: Identifying Lower Transmission Mount Nuts
    G05987668Courtesy of AMERICAN HONDA MOTOR CO., INC.
  37. Attach the front subframe adapter (VSB02C000016) to a transmission jack, then raise the jack to the subframe Hang the belt (A) over the front of the subframe, then secure the belt by inserting the stop (B) and then tightening the wing nut (C)
    Fig 21: Identifying Front Subframe Adapter (VSB02C000016) On Transmission Jack
    G05987669Courtesy of AMERICAN HONDA MOTOR CO., INC.
  38. Remove the stiffener mounting bolt (A) on both sides
    Fig 22: Identifying Stiffener Mounting Bolt And Subframe Mounting Bolts
    G05987670Courtesy of AMERICAN HONDA MOTOR CO., INC.
  39. Loosen the subframe mounting bolts (B) so they are about 20 mm (13/16 in) from the mounting surface Do not loosen the front subframe mounting bolts more than necessary
  40. Remove the stiffener mounting bolt (A) and subframe mounting bolts (B) from the rear stiffeners (C)
    Fig 23: Identifying Stiffener Mounting Bolt, Subframe Mounting Bolts And Rear Stiffeners
    G05987671Courtesy of AMERICAN HONDA MOTOR CO., INC.
  41. Lower the jack slowly until the front subframe has dropped about 70 mm (2 3/4 in)
    Fig 24: Identifying Lowering Jack
    G05987672Courtesy of AMERICAN HONDA MOTOR CO., INC.
  42. Remove the EPS subharness (A) from the steering gearbox (B)
    NOTE: Disconnect the EPS subharness 3P connector (C) by pushing the lock (D) and pulling down the lever (E)
    Fig 25: Identifying EPS Subharness 3P Connector, Lock And Lever
    G05987673Courtesy of AMERICAN HONDA MOTOR CO., INC.
  43. Carefully move the steering gearbox (A) toward the driver's side until the pinion shaft clears the fender well opening on the body
    Fig 26: Identifying Steering Gearbox
    G05987674Courtesy of AMERICAN HONDA MOTOR CO., INC.
  44. Remove the steering gearbox (A) through the fender well opening on the driver's side
    Fig 27: Removing Steering Gearbox
    G05987675Courtesy of AMERICAN HONDA MOTOR CO., INC.
  45. Remove the pinion shaft grommet (A) from the top of the torque sensor (B)
    Fig 28: Identifying Pinion Shaft Grommet And Torque Sensor
    G05987676Courtesy of AMERICAN HONDA MOTOR CO., INC.