LEMON Manuals: Even more car manuals for everyone
Home >> Acura >> 2009 >> RDX >> Repair and Diagnosis >> Engine Performance >> System >> Variable Valve Timing And Lift Electronic Control (VTEC) >> DTC Troubleshooting >> DTC P0010: VTC Oil Control Solenoid Valve Malfunction

DTC P0010: VTC Oil Control Solenoid Valve Malfunction

NOTE: Before you troubleshoot, record all freeze data and any on-board snapshot, and review the general troubleshooting information (see GENERAL TROUBLESHOOTING INFORMATION ).
  1. Turn the ignition switch ON (II).
  2. Clear the DTC with the HDS.
  3. Start the engine. Hold the engine speed at 3,000 RPM without load (in Park or neutral) until the radiator fan comes on, then let it idle.
  4. Do the VTC TEST in the INSPECTION MENU with the HDS.
  5. Check for Temporary DTCs or DTCs with the HDS.

    Is DTC P0010 indicated? 

    YES  - Go to step  6.

    NO  - Intermittent failure, the system is OK at this time. Check for poor connections or loose terminals at the VTC oil control solenoid valve and the PCM.

  6. Turn the ignition switch OFF.
  7. Disconnect the VTC oil control solenoid valve 2P connector.
  8. At the solenoid side, measure resistance between VTC oil control solenoid valve 2P connector terminals No. 1 and No. 2.
    Fig 1: Measuring Resistance Between VTC Oil Control Solenoid Valve 2P Connector Terminals No. 1 And 2
    G05447024Courtesy of AMERICAN HONDA MOTOR CO., INC.

    Is there 6.75- 8.25 Ω at room temperature? 

    YES  - Go to step  9.

    NO  - Go to step  14.

  9. Check for continuity between VTC oil control solenoid valve 2P connector terminal No. 1 and body ground.
    Fig 2: Checking Continuity Between VTC Oil Control Solenoid Valve 2P Connector Terminal No. 1 And Body Ground
    G05447025Courtesy of AMERICAN HONDA MOTOR CO., INC.

    Is there continuity? 

    YES  - Go to step  10.

    NO  - Repair open in the wire between the VTC oil control solenoid valve and G101 (see ENGINE WIRE HARNESS ), then go to step  15.

  10. Jump the SCS line with the HDS.
  11. Disconnect PCM connector C (44P).
  12. Check for continuity between PCM connector terminal C23 and body ground.
    Fig 3: Checking Continuity Between PCM Connector Terminal C23 And Body Ground
    G05447026Courtesy of AMERICAN HONDA MOTOR CO., INC.

    Is there continuity? 

    YES  - Repair short in the wire between the PCM (C23) and the VTC oil control solenoid valve, then go to step  15.

    NO  - Go to step  13.

  13. Check for continuity between VTC oil control solenoid valve 2P connector terminal No. 2 and PCM connector terminal C23.
    Fig 4: Checking Continuity Between VTC Oil Control Solenoid Valve 2P Connector Terminal No. 2 And PCM Connector Terminal C23
    G05447027Courtesy of AMERICAN HONDA MOTOR CO., INC.

    Is there continuity? 

    YES  - Go to step  22.

    NO  - Repair open in the wire between the PCM (C23) and the VTC oil control solenoid valve, then go to step  15.

  14. Replace the VTC oil control solenoid valve (see VTC OIL CONTROL SOLENOID VALVE REMOVAL/TEST/INSTALLATION ).
  15. Reconnect all connectors.
  16. Turn the ignition switch ON (II).
  17. Reset the PCM with the HDS.
  18. Do the PCM idle learn procedure (see PCM IDLE LEARN PROCEDURE ).
  19. Do the VTC TEST in the INSPECTION MENU with the HDS.
  20. Check for Temporary DTCs or DTCs with the HDS.

    Is DTC P0010 indicated? 

    YES  - Check for poor connections or loose terminals at the VTC oil control solenoid valve and the PCM, then go to step  1.

    NO  - Go to step  21.

  21. Monitor the OBD STATUS for DTC P0010 in the DTCs MENU with the HDS.

    Does the screen indicate PASSED? 

    YES  - Troubleshooting is complete. If any other Temporary DTCs or DTCs were indicated in step 20, go to the indicated DTCs troubleshooting.

    NO  - If the screen indicates FAILED, check for poor connections or loose terminals at the VTC oil control solenoid valve and the PCM, then go to step  1. If the screen indicates NOT COMPLETED, go to step  19.

  22. Reconnect all connectors.
  23. Update the PCM if it does not have the latest software (see PCM UPDATE ), or substitute a known-good PCM (see SUBSTITUTING THE PCM ).
  24. Do the VTC TEST in the INSPECTION MENU with the HDS.
  25. Check for Temporary DTCs or DTCs with the HDS.

    Is DTC P0010 indicated? 

    YES  - Check for poor connections or loose terminals at the VTC oil control solenoid valve and the PCM. If the PCM was updated, substitute a known-good PCM (see SUBSTITUTING THE PCM ), then go to step  24. If the PCM was substituted, go to step  1.

    NO  - Go to step  26.

  26. Monitor the OBD STATUS for DTC P0010 in the DTCs MENU with the HDS.

    Does the screen indicate PASSED? 

    YES  - If the PCM was updated, troubleshooting is complete. If the PCM was substituted, replace the original PCM (see PCM REPLACEMENT ). If any other Temporary DTCs or DTCs were indicated in step 25, go to the indicated DTCs troubleshooting.

    NO  - If the screen indicates FAILED, check for poor connections or loose terminals at the VTC oil control solenoid valve and the PCM. If the PCM was updated, substitute a known-good PCM (see SUBSTITUTING THE PCM ), then go to step  24. If the PCM was substituted, go to step  1. If the screen indicates NOT COMPLETED, go to step  24.