A/C Compressor Clutch Circuit Troubleshooting
NOTE:
- Do not use this troubleshooting procedure if the fans are also inoperative. Refer to the SYMPTOM TROUBLESHOOTING INDEX .
- Before performing symptom troubleshooting, check for powertrain DTCs (see GENERAL TROUBLESHOOTING INFORMATION ).
- Check the No. 1 (30 A) fuse in the underhood fuse/relay box, and the No. 14 (10 A) fuse in the under-dash fuse/relay box.
Are the fuses OK?
- YES - Go to step 2.
- NO - Replace the fuse(s), and recheck.
- Check the engine coolant temperature, the throttle position sensor, and the idle speed (use the HDS PGM-FI data list if possible).ECT SENSOR REFERENCE
ECT Sensor 169-194 °F (76-90 °C) TP Sensor About 0.5 V RPM K20A02, K20Z1 engine: 700 K20A03 engine: 650 Are the engine coolant temperature, throttle position, and idle speed OK?
- YES - Go to step 3.
- NO - Troubleshoot and repair the cause of the high engine coolant temperature, low idle, or excessively high throttle position sensor reading.
- Remove the A/C compressor clutch relay from the underhood fuse/relay box, and test it (see
POWER RELAY TEST
).
Is the relay OK?
- YES - Go to step 4.
- NO - Replace the A/C compressor clutch relay.
- Measure the voltage between the No. 2 terminal of the A/C compressor clutch relay 4P socket and body ground.
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Is there battery voltage?
- YES - Go to step 5.
- NO - Replace the underhood fuse/relay box.
- Connect the No. 1 and No. 2 terminals of the A/C compressor clutch relay 4P socket with a jumper wire.
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Does the A/C compressor clutch click?
- YES - Go to step 6.
- NO - Go to step 14.
- Disconnect the jumper wire.
- Turn the ignition switch ON (II).
- Measure the voltage between the No. 3 terminal of the A/C compressor clutch relay 4P socket and body ground.
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Is there battery voltage?
- YES - Go to step 9.
- NO - Repair open in the BLK/YEL wire between the No. 14 (10 A) fuse in the under-dash fuse/relay box and the A/C compressor clutch relay.
- Turn the ignition switch OFF.
- Reinstall the A/C compressor clutch relay.
- Make sure the A/C switch is OFF.
- Turn the ignition switch ON (II).
- Using a backprobe set, measure the voltage between the No. 18 terminal of ECM/PCM connector E (31P) and body ground with the ECM/PCM connectors connected.
'02-04 models
Fig 4: Measuring Voltage Between Terminal Of ECM/PCM Connector E (31P) And Body Ground ('02-04 Models)Courtesy of AMERICAN HONDA MOTOR CO., INC.
'05-06 models
Fig 5: Measuring Voltage Between Terminal Of ECM/PCM Connector E (31P) And Body Ground ('05-06 Models)Courtesy of AMERICAN HONDA MOTOR CO., INC.
Is there battery voltage?
- YES - Update the ECM/PCM if it does not have the latest software, or substitute a known-good ECM/PCM, then recheck (see HOW TO UPDATE THE ECM/PCM ). If the symptom/indication goes away with a known-good ECM/PCM, replace the original ECM/PCM.
- NO - Repair open in the wire between the A/C compressor clutch relay and the ECM/PCM.
- Disconnect the jumper wire.
- Disconnect the A/C compressor clutch 1P connector.
- Check for continuity between the No. 1 terminal of the A/C compressor clutch relay 4P socket and the No. 1 terminal of the A/C compressor clutch 1P connector.Fig 6: Checking Continuity Between A/C Compressor Clutch Relay 4P Socket And A/C Compressor Clutch 1P Connector Terminals
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Is there continuity?
- YES - Check the A/C compressor clutch clearance, the thermal protector, and the A/C compressor clutch field coil (see A/C COMPRESSOR CLUTCH CHECK ).
- NO - Repair open in the wire between the A/C compressor clutch relay and the A/C compressor clutch.