LEMON Manuals: Even more car manuals for everyone

Manual Transaxle Unit: Reassembly: Procedure

  1. SECONDARY SHAFT COMPONENT AND PRIMARY SHAFT COMPONENT ASSEMBLY NOTE 
    1. Assemble the secondary shaft component and primary shaft component to the clutch housing component as a single unit.
      GTY491070Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Primary Shaft Component
      *b Secondary Shaft Component
    2. Shake the assembled parts and assemble each one completely.
  2. REVERSE IDLER SHAFT ASSEMBLY NOTE 
    1. Align the reverse idler shaft anchor bolt installation hole of the reverse idler shaft with the positioning mark of the clutch housing, and assemble the reverse idler shaft as shown in the figure.
      GTY485059Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Reverse Idler Shaft
      *b Reverse Idler Shaft Anchor Bolt Installation Hole
      *c Positioning Mark
  3. SHIFT FORK, SHIFT ROD END, SHIFT ROD, SPRING, AND REVERSE GATE ASSEMBLY NOTE 
    1. Assemble the shift fork (5GR/6GR), shift rod end (5GR/6GR), shift rod (5GR/6GR), spring, and reverse gate using the following procedure:
      GTY486005Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Shift Fork (5GR/6GR)
      *b Assembly Direction
      *c Shift Rod End (5GR/6GR)
      *d Reverse Gate
      *e Shift Rod (5GR/6GR)
      *f Spring
      N*m (kgf*cm, ft.*lbf): Specified torque
      • Non-reusable part

      Torque: 13.5 N*m (138 kgf*cm, 10 ft.*lbf) 

      1. Pass the shift rod through the assembly hole of the shift fork.
      2. Pass the shift rod through the assembly hole of the shift rod end.
      3. Pass the shift rod through the spring.
      4. Pass the shift rod through the assembly hole of the reverse gate.
      5. Assemble the shift fork to the clutch hub sleeve.
      6. Verify the assembly direction of the shift rod.

        HINT: 

        Assemble the shift rod so that the positioning pits used for verifying the assembly direction are facing the transaxle case side and the exterior side of the manual transaxle.

      7. Install the spring as shown in the figure.
        1. Shift rod end side
          GTY488187Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
          *a Shift Rod End (5GR/6GR)
          *b Spring
        2. Reverse gate side
          GTY493626Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
          *a Spring
          *b Reverse Gate
          1. Assemble the shift rod to the clutch housing.
          2. Tighten new bolts and assemble the shift rod end and the shift fork to the shift rod.
    2. Assemble the shift fork (3GR/4GR), shift rod end (3GR/4GR), shift rod end (reverse), and shift rod (3GR/4GR) using the following procedure:
      GTY494589Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Shift Fork (3GR/4GR)
      *b Shift Rod End (3GR/4GR)
      *c Assembly Direction
      *d Shift Rod End (Reverse)
      N*m (kgf*cm, ft.*lbf): Specified torque
      • Non-reusable part

      Torque: 13.5 N*m (138 kgf*cm, 10 ft.*lbf) 

      1. Assemble the shift fork to the clutch hub sleeve.
      2. Verify the assembly direction of the shift rod.

        HINT: 

        Assemble the shift rod so that the positioning pits used for verifying the assembly direction are facing the transaxle case side and the exterior side of the manual transaxle.

      3. Pass the shift rod through the assembly hole of the shift fork.
      4. Pass the shift rod through the assembly hole of the shift rod end (3GR/4GR).
      5. Pass the shift rod through the assembly hole of the shift rod end (reverse).
      6. Assemble the shift rod to the clutch housing.
      7. Tighten new bolts and assemble the shift rod end and the shift fork to the shift rod.
    3. Assemble the shift fork (1GR/2GR), shift rod end (1GR/2GR), and shift rod (1GR/2GR) using the following procedure:
      GTY494721Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Shift Rod (1GR/2GR)
      *b Shift Fork (1GR/2GR)
      *c Assembly Direction
      *d Shift Rod End (1GR/2GR)
      N*m (kgf*cm, ft.*lbf): Specified torque
      • Non-reusable part

      Torque: 13.5 N*m (138 kgf*cm, 10 ft.*lbf) 

      1. Assemble the shift fork to the clutch hub sleeve.
      2. Verify the assembly direction of the shift rod.

        HINT: 

        Assemble the shift rod so that the positioning pits used for verifying the assembly direction are facing the transaxle case side and the exterior side of the manual transaxle.

      3. Pass the shift rod through the assembly hole of the shift fork.
      4. Set the shift rod end to the position shown in the figure and pass the shift rod through the assembly hole of the shift rod end.
      5. Assemble the shift rod to the clutch housing.
      6. Tighten new bolts and assemble the shift rod end and the shift fork to the shift rod.
  4. TRANSAXLE CASE COMPONENT ASSEMBLY NOTE 
    1. Apply silicone sealant TB1216B or equivalent to the clutch housing as shown in the figure.
      GTY493147Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Clutch Housing
      *b 1 to 2 mm (0.04 to 0.07 in.)
      *c 2 mm (0.07 in.)
      *d 3 mm (0.12 in.)
      Sealant
    2. Assemble the transaxle case component using the following procedure:
      NOTE:

      Assemble the transaxle case component before the applied silicone sealant starts to harden.

      1. Rotate the control rod of the control set as shown in the figure.
        GTY492641Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Control Rod
        *b Control Set
      2. Hold the reverse idler gear so that the control set is in the reverse condition.
        GTY485492Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Control Set
        *b Reverse Idler Gear
      3. Pull the shift lever in the direction shown in the figure.
        GTY487013Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Shift Lever
      4. Align the select lever with the positioning mark and set it to the reverse position.
        GTY489118Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Select Lever
        *b Align
        *c Positioning Mark
      5. Cover the transaxle case component.
        GTY494972Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Transaxle Case Component
      6. Rotate the shift lever in the direction shown in the figure.
        GTY491824Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Shift Lever
      7. Press the shift lever in the direction shown in the figure.
        GTY488192Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Shift Lever
      8. Assemble the shift lever shaft anchor bolt.
        GTY489824Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Shift Lever Shaft Anchor Bolt
        *b Gasket
        N*m (kgf*cm, ft.*lbf): Specified torque
        • Non-reusable part

        Torque: 11.5 N*m (117 kgf*cm, 8 ft.*lbf) 

      9. Widen the clip using snap ring pliers and hold.
        GTY485696Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Service Hole
        *b Clip
        *c Snap Ring Pliers
      10. While pressing the transaxle case so that it does not move, operate the select lever and shift lever to shift to 2nd gear, hold the secondary shaft component, and engage the clip with the groove of the ball bearing assembled to the secondary shaft.
        GTY487831Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Select Lever
        *b Shift Lever
        *c 1: Shift to 1GR/2GR
        *d 2: Shift to 2GR
      11. Tighten the transaxle case installation bolts and assemble the transaxle case component.
        GTY483771Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        N*m (kgf*cm, ft.*lbf): Specified torque

        Torque: 26 N*m (265 kgf*cm, 19 ft.*lbf) 

        Torque: 45 N*m (459 kgf*cm, 33 ft.*lbf) 

  5. OIL SEAL ASSEMBLY NOTE 
    1. Using the SSTs and a hammer, install a new oil seal (LH).
      • SST: 49G03079649G030797 
      GTY492406Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Oil Seal (LH) *b Hammering Direction
      *c A *d B
      • Non-reusable part Oil

      A

      0.3 mm (0.01 in.)

      B

      0.3 mm (0.01 in.)

    2. Using the SSTs and a hammer, install a new oil seal (RH).
      • SST: 49G03079649G030797 
      GTY488245Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Oil Seal (RH) *b Hammering Direction
      *c A *d B
      • Non-reusable part Oil

      A

      0.3 mm (0.01 in.)

      B

      0.3 mm (0.01 in.)

  6. SERVICE HOLE PLATE ASSEMBLY NOTE 
    1. Verify that there is no damage on the service hole plate installation surface.
    2. Apply silicone sealant TB1216B or equivalent to the service hole plate as shown in the figure.
      GTY483502Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Service Hole Plate
      *b 1 to 2 mm (0.04 to 0.07 in.)
      *c 2.8 mm (0.11 in.)
      Sealant
    3. Assemble the service hole plate.
      NOTE:

      Assemble the service hole plate before the applied silicone sealant starts to harden.

  7. STUD BOLT ASSEMBLY NOTE 
    1. Assemble the stud bolts.
      GTY484583Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Stud Bolt No. 1
      *b Stud Bolt No. 2
      *c Stud Bolt No. 3
    2. Measure the projection of the stud bolts.
      GTY486803Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Stud Bolt No. 1
      *b Stud Bolt No. 2
      *c Stud Bolt No. 3
      *d A
      *e B
      *f C

      Projection A of stud bolt No. 1

      70.7 to 72.7 mm (2.79 to 2.86 in.)

      Projection B of stud bolt No. 2

      40.0 to 42.0 mm (1.58 to 1.65 in.)

      Projection C of stud bolt No. 3

      70.7 to 72.7 mm (2.79 to 2.86 in.)

      If the projection amount is not within the range, adjust the projection amount of the stud bolt.

  8. TRANSAXLE ASSEMBLY 
    1. Step 1
      1. Perform the shim adjustment and select a shim of the appropriate thickness.

        Refer to ADJUSTMENT 

      2. Assemble the SST to the SST.
        • SST: 49G0190A0490107680A 
        GTY493038Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

        Bolt used

        Part number 

        9YA02 A220 or M12 x 1.75 bolt (length 40 mm (1.6 in.))

        Torque: 103 N*m (1050 kgf*cm, 76 ft.*lbf) 

      3. Assemble the clutch housing component to the SST.
        • SST: 49G0190A0 
        GTY489357Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Bolt A
        *b Bolt B
        *c Bolt C
        *d Bolt D

        Bolt A

        Part number 

        99450 1055 or M10 x 1.25 bolt (length 55 mm (2.2 in.)) and nut (M10 x 1.25)

        Bolt A tightening torque 

        Torque: 45 N*m (459 kgf*cm, 33 ft.*lbf) 

        Bolt B

        SST (component part for 49G0190A0: 49G019003)

        Bolt B tightening torque 

        Torque: 103 N*m (1050 kgf*cm, 76 ft.*lbf) 

        Bolt C

        Part number 

        9YA02 1080 or M10 x 1.5 bolt (length 55 mm (2.2 in.))

        Bolt C tightening torque 

        Torque: 45 N*m (459 kgf*cm, 33 ft.*lbf) 

        Bolt D

        Part number 

        99450 1030 or M10 x 1.25 bolt (length 30 mm (1.2 in.))

        Bolt D tightening torque 

        Torque: 45 N*m (459 kgf*cm, 33 ft.*lbf) 

      4. Install the clutch housing component.
        GTY489129Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *1 Clutch Housing Component *2 Differential
        *3 Secondary Shaft Component *4 Primary Shaft Component
        *5 Reverse Idler Gear *6 Reverse Idler Shaft
        *7 Reverse Gate *8 Spring
        *9 Shift Fork *10 Shift Rod End
        *11 Shift Rod *12 Control Set
        *13 Reverse Lever Component *14 Magnet
        *15 Shim *16 Transaxle Case Component
        *17 Gasket *18 Shift Lever Shaft Anchor Bolt
        *a Selective - -
        N*m (kgf*cm, ft.*lbf): Specified torque • Non-reusable part
        Specified Oil to Individual Parts Petroleum Jelly
        Sealant - -
      5. Install the differential.
      6. Install the secondary shaft component.

        See step  1

      7. Install the primary shaft component.

        See step  1

      8. Install the reverse idler gear.
      9. Install the reverse idler shaft.

        See step  2

      10. Install the reverse gate.

        See step  3

      11. Install the spring.

        See step  3

      12. Install the shift fork.

        Torque: 13.5 N*m (138 kgf*cm, 10 ft.*lbf) 

        See step  3

      13. Install the shift rod end.

        Torque: 13.5 N*m (138 kgf*cm, 10 ft.*lbf) 

        See step  3

      14. Install the shift rod.

        See step  3

      15. Install the control set.

        Torque: 15.5 N*m (158 kgf*cm, 11 ft.*lbf) 

      16. Install the reverse lever component.

        Torque: 15.5 N*m (158 kgf*cm, 11 ft.*lbf) 

      17. Install the magnet.
      18. Install the shim.

        See step  4

      19. Install the transaxle case component.

        Torque: 26 N*m (265 kgf*cm, 19 ft.*lbf) 

        Torque: 45 N*m (459 kgf*cm, 33 ft.*lbf) 

        See step  4

      20. Install the gasket.

        See step  4

      21. Install the shift lever shaft anchor bolt.

        Torque: 11.5 N*m (117 kgf*cm, 8 ft.*lbf) 

        See step  4

    2. Step 2
      1. Install the gasket.
        GTY487094Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *1 Gasket *2 Drain Plug
        *3 Pin *4 Spring
        *5 Gasket *6 Plug
        *7 Oil Seal *8 Service Hole Plate
        *9 Reverse Idler Shaft Anchor Bolt *10 Gasket
        *11 Oil Level Plug *12 Gasket
        *13 Back-Up Light Switch *14 Gasket
        *15 Plug *16 Gasket
        *17 Neutral Switch No. 1 *18 Detent Ball
        *19 Spring *20 Gasket
        *21 Plug *22 Stud Bolt
        N*m (kgf*cm, ft.*lbf): Specified torque • Non-reusable part
        Oil Sealant
      2. Install the drain plug.

        Torque: 49 N*m (500 kgf*cm, 36 ft.*lbf) 

      3. Install the pin.
      4. Install the spring.
      5. Install the gasket.
      6. Install the plug.

        Torque: 24.5 N*m (250 kgf*cm, 18 ft.*lbf) 

      7. Install the oil seal.

        See step  5

      8. Install the service hole plate.

        Torque: 9.0 N*m (92 kgf*cm, 80 in.*lbf) 

        See step  6

      9. Install the reverse idler shaft anchor bolt.

        Torque: 22 N*m (224 kgf*cm, 16 ft.*lbf) 

      10. Install the gasket.
      11. Install the oil level plug.

        Torque: 49 N*m (500 kgf*cm, 36 ft.*lbf) 

      12. Install the gasket.
      13. Install the back-up light switch.

        Torque: 24.5 N*m (250 kgf*cm, 18 ft.*lbf) 

      14. Install the gasket.
      15. Install the plug.

        Torque: 24.5 N*m (250 kgf*cm, 18 ft.*lbf) 

      16. Install the gasket.
      17. Install the neutral switch No. 1.

        Torque: 24.5 N*m (250 kgf*cm, 18 ft.*lbf) 

      18. Install the detent ball.
      19. Install the spring.
      20. Install the gasket.
      21. Install the plug.

        Torque: 24.5 N*m (250 kgf*cm, 18 ft.*lbf) 

      22. Install the stud bolt.

        See step  7