LEMON Manuals: Even more car manuals for everyone

Manual Transaxle Unit: Disassembly: Procedure

  1. SERVICE HOLE PLATE REMOVAL NOTE 
    NOTE:

    Do not damage the transaxle case when removing the service hole plate.

    1. Remove the service hole plate while lightly tapping the side of the service hole plate using a cloth wrapped flathead screwdriver.
      GTY486560Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Service Hole Plate
  2. TRANSAXLE CASE COMPONENT REMOVAL NOTE 
    1. Remove the transaxle case component installation bolts.
      GTY489126Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. While pulling up the ball bearing outer race using pliers as shown in the figure, turn the clip to align the clip opening with the service hole.
      GTY483625Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Ball Bearing Outer Race
      *b Clip
      *c Pliers
      NOTE:

      Cover a cloth with the servicing area and hold the ball bearing outer race with pliers while being careful not to damage the ball bearing outer race.

    3. Keep apart the pliers from the ball bearing outer race.
    4. Insert the snap ring pliers into the service hole, widen the clip, and disconnect the secondary shaft component from the transaxle case.
      GTY494973Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Snap Ring Pliers
      *b Service Hole
      *c Clip
      NOTE:

      Be careful not to damage or scratch the transaxle case when using the snap ring pliers. Otherwise, oil could leak.

      HINT: 

      If the clip and the secondary shaft component are disengaged, the secondary shaft component will dislodge slightly so that it can be disconnected from the transaxle case.

    5. Align the select lever with the positioning mark and set it to the reverse position.
      GTY483787Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Positioning Mark
      *b Select Lever
      *c Align
    6. Pull the shift lever in the direction shown in the figure.
      GTY484049Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Shift Lever
    7. Tap the locations shown in the figure using a plastic hammer to remove the transaxle case component.
      GTY489063Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  3. PRIMARY SHAFT COMPONENT, SECONDARY SHAFT COMPONENT REMOVAL NOTE 
    1. Remove the primary shaft component and secondary shaft component as a single unit.
      GTY491219Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Primary Shaft Component
      *b Secondary Shaft Component
  4. TRANSAXLE DISASSEMBLY 
    1. Step 1
      GTY493798Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. Assemble the SST to the SST.
        • SST: 49G0190A0490107680A 

        Bolt used

        Part number 

        9YA02 A220 or M12 x 1.75 bolt (length 40 mm (1.6 in.))

        Torque: 103 N*m (1050 kgf*cm, 76 ft.*lbf) 

      2. Assemble the MTX to the SST.
        • SST: 49G0190A0490107680A49G019003 

        Bolt A

        Part number 

        99450 1055, or M10 x 1.25 bolt (length 55 mm (2.2 in.)) and nut (M10 x 1.25)

        Bolt A tightening torque 

        Torque: 45 N*m (459 kgf*cm, 33 ft.*lbf) 

        Bolt B

        SST (component part for 49G0190A0: 49G019003)

        Bolt B tightening torque 

        Torque: 103 N*m (1050 kgf*cm, 76 ft.*lbf) 

        Bolt C

        Part number 

        9YA02 1080, or M10 x 1.5 bolt (length 55 mm (2.2 in.))

        Bolt C tightening torque 

        Torque: 45 N*m (459 kgf*cm, 33 ft.*lbf) 

        Bolt D

        Part number 

        99450 1030 or M10 x 1.25 bolt (length 30 mm (1.2 in.)

        Bolt D tightening torque 

        Torque: 45 N*m (459 kgf*cm, 33 ft.*lbf) 

        GTY485052Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Bolt A
        *b Bolt B
        *c Bolt C
        *d Bolt D
      3. Remove the stud bolt.
        GTY495087Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *1 Stud Bolt *2 Plug
        *3 Gasket *4 Spring
        *5 Detent Ball *6 Neutral Switch
        *7 Gasket *8 Shift Lever Shaft Anchor Bolt
        *9 Gasket *10 Plug
        *11 Gasket *12 Back-Up Light Switch
        *13 Gasket *14 Oil Level Plug
        *15 Gasket *16 Reverse Idler Shaft Anchor Bolt
        *17 Service Hole Plate *18 Oil Seal
        *19 Plug *20 Gasket
        *21 Spring *22 Pin
        *23 Drain Plug *24 Gasket
        N*m (kgf*cm, ft.*lbf): Specified torque • Non-reusable part
      4. Remove the plug.
      5. Remove the gasket.
      6. Remove the spring.
      7. Remove the detent ball.
      8. Remove the neutral switch.
      9. Remove the gasket.
      10. Remove the shift lever shaft anchor bolt.
      11. Remove the gasket.
      12. Remove the plug.
      13. Remove the gasket.
      14. Remove the back-up light switch.
      15. Remove the gasket.
      16. Remove the oil level plug.
      17. Remove the gasket.
      18. Remove the reverse idler shaft anchor bolt.
      19. Remove the service hole plate.

        See step  1

      20. Remove the oil seal.
      21. Remove the plug.
      22. Remove the gasket.
      23. Remove the spring.
      24. Remove the pin.
      25. Remove the drain plug.
      26. Remove the gasket.
    2. Step 2
      GTY488445Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Transaxle Case Component *2 Shim
      *3 Magnet *4 Control Set
      *5 Reverse Lever Component *6 Shift Rod
      *7 Shift Rod End *8 Shift Fork
      *9 Spring *10 Reverse Gate
      *11 Reverse Idler Shaft *12 Reverse Idler Gear
      *13 Primary Shaft Component *14 Secondary Shaft Component
      *15 Differential *16 Clutch Housing Component
      N*m (kgf*cm, ft.*lbf): Specified torque • Non-reusable part
      1. Remove the transaxle case component.

        See step  2

      2. Remove the shim.
      3. Remove the magnet.
      4. Remove the control set.
      5. Remove the reverse lever component.
      6. Remove the shift rod.
      7. Remove the shift rod end.
      8. Remove the shift fork.
      9. Remove the spring.
      10. Remove the reverse gate.
      11. Remove the reverse idler shaft.
      12. Remove the reverse idler gear.
      13. Remove the primary shaft component.

        See step  3

      14. Remove the secondary shaft component.

        See step  3

      15. Remove the differential.
      16. Remove the clutch housing component.
    3. Remove the silicone sealant of the transaxle case component and clutch housing component, and clean all the parts.