LEMON Manuals: Even more car manuals for everyone

Manual Transaxle Assembly: Installation: Procedure

  1. INSTALL MANUAL TRANSAXLE 
    WARNING:

    Remove the manual transaxle carefully, holding it steady. If the manual transaxle falls it could be damaged or cause injury.

    1. Set the manual transaxle on a jack and lift into place.
      GTY486336Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Manual Transaxle
      *b Jack
    2. Install the manual transaxle to the engine, and tighten the transaxle mounting bolts.

      Torque: 45 N*m (459 kgf*cm, 33 ft.*lbf) 

      GTY493402Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      N*m (kgf*cm, ft.*lbf): Specified torque
    3. Assemble the stud bolt No. 1.
      GTY491157Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Stud Bolt No. 1
    4. Measure the projection of the stud bolts.

      Projection A of stud bolt No. 1

      70.7 to 72.7 mm (2.79 to 2.86 in.)

      Projection B of stud bolt No. 2

      40.0 to 42.0 mm (1.58 to 1.65 in.)

      Projection C of stud bolt No. 3

      70.7 to 72.7 mm (2.79 to 2.86 in.)

      1. If the projection amount is not within the range, adjust the projection amount of the stud bolt.
      GTY494350Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Stud Bolt No. 1
      *b Stud Bolt No. 2
      *c Stud Bolt No. 3
      *d Projection A of Stud Bolt No. 1
      *e Projection B of Stud Bolt No. 2
      *f Projection C of Stud Bolt No. 3
    5. Install the No. 4 engine mount bracket to No. 4 engine mount rubber, and temporarily tighten the installation bolt.
      GTY487284Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a No. 4 Engine Mount Rubber
      *b No. 4 Engine Mount Bracket
      *c Bolt
    6. GTY484872Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a No. 4 Engine Mount Bracket
      *b Stud Bolt
      *c Nut

      Lift up the manual transaxle using the SST, pass the stud bolt through the No. 4 engine mount bracket, and temporarily tighten the No. 4 engine mount bracket installation nuts.

      • SST: 49C0175A049L0175A0 
    7. Install the No. 1 engine mount bracket to the manual transaxle using the procedure shown in the figure, and tighten the bolts.
      GTY485679Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a No. 1 Engine Mount Bracket
      N*m (kgf*cm, ft.*lbf): Specified torque

      Torque: 91 N*m (928 kgf*cm, 67 ft.*lbf) 

    8. Install the front crossmember component and No. 1 engine mount rubber as a single unit.

      Refer to INSTALLATION

    9. Temporarily tighten the No. 1 engine mount rubber installation bolts.
      GTY493903Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a No. 1 Engine Mount Rubber
      *b Bolt
    10. Align the alignment marks on the No. 4 engine mount bracket and nuts, and temporarily tighten the nuts shown in the figure.
      GTY487892Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Good *b No Good
      *c Alignment Mark *d Alignment Marks and Nuts Are Aligned
      *e No. 4 Engine Mount Bracket *f Vehicle Front
    11. Tighten the No. 4 engine mount bracket installation nuts and bolt in the order shown in the figure.

      1, 2, 3 

      Torque: 104 N*m (1061 kgf*cm, 77 ft.*lbf) 

      4 

      Torque: 90 N*m (918 kgf*cm, 66 ft.*lbf) 

      GTY487522Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a No. 4 Engine Mount Bracket
      *b Vehicle Front
      N*m (kgf*cm, ft.*lbf): Specified torque
    12. Remove the SSTs.
      • SST: 49C0175A049L0175A0 
    13. Tighten the No. 1 engine mount rubber installation bolts in the order shown in the figure.
      GTY494328Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      N*m (kgf*cm, ft.*lbf): Specified torque

      1 

      Torque: 156.5 N*m (1596 kgf*cm, 115 ft.*lbf) 

      2 

      Torque: 147 N*m (1499 kgf*cm, 108 ft.*lbf) 

    14. Connect and/or install the following parts to the underside of the vehicle.
      1. Install the starter.

        Refer to INSTALLATION

      2. Install the clutch release cylinder to the manual transaxle.

        Refer to INSTALLATION

    15. Connect and/or install the following parts related to the suspension and axle.
      1. Install the drive shaft (RH) to the manual transaxle.

        Refer to INSTALLATION

      2. Install the drive shaft (LH) to the manual transaxle.

        Refer to INSTALLATION

      3. Install the front lower arms to the steering knuckles.

        Refer to INSTALLATION

      4. Install the front stabilizer control link to the front shock absorber.

        Refer to INSTALLATION

      5. Install the tie-rod end ball joints to the steering knuckles.

        Refer to INSTALLATION

      6. Install the front speed sensor to the steering knuckles.

        Refer to INSTALLATION

        Refer to INSTALLATION

      7. Install the brake hose to the front shock absorber.

        Refer to INSTALLATION

      8. Install the splash shield.

        Refer to INSTALLATION

      9. Install the front tires.

        Refer to PRECAUTION

    16. Connect and/or install the following parts in the engine compartment.
      1. Install the clip shown in the figure.
        GTY484685Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Fuel Hose
        *b Clip
      2. Install the clip shown in the figure.
        GTY487088Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Intake Manifold
        *b Clip
      3. Install the lower radiator hose clip and brackets to the manual transaxle.
        GTY495098Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Lower Radiator Hose
        *b Wiring Harness
        *c Bracket
        *d Bolt
        *e Clip
        N*m (kgf*cm, ft.*lbf): Specified torque

        Torque: 9.0 N*m (92 kgf*cm, 80 in.*lbf) 

      4. Connect the neutral switch connector.

        Refer to INSTALLATION 

      5. Connect the back-up light switch connector.

        Refer to INSTALLATION 

      6. Install the ground to the No. 4 engine mount bracket.
        GTY491497Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a No. 4 Engine Mount Bracket
        *b Ground
        *c Bolt
        N*m (kgf*cm, ft.*lbf): Specified torque

        Torque: 10.5 N*m (107 kgf*cm, 8 ft.*lbf) 

      7. Install the control cable bracket to the manual transaxle.
        GTY491539Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Control Cable Bracket
        *b Bolt
        N*m (kgf*cm, ft.*lbf): Specified torque

        Torque: 19 N*m (194 kgf*cm, 14 ft.*lbf) 

      8. Install the control cable to the manual transaxle.

        Refer to INSTALLATION 

      9. Install the battery tray and PCM component.

        Refer to INSTALLATION

      10. Install the air cleaner, air hose and fresh air duct as a single unit.

        Refer to INSTALLATION

    17. Install the front under cover No. 1.

      Refer to INSTALLATION

    18. Add the specified amount of manual transaxle oil.

      Refer to REPLACEMENT 

    19. Install the front under cover No. 2.

      Refer to INSTALLATION

    20. Connect the negative battery cable.

      Refer to INSTALLATION

    21. Install the plug hole plate.

      Refer to INSTALLATION

    22. If the manual transaxle is overhauled, perform the INSPECTION AFTER MANUAL TRANSAXLE OVERHAUL.

      Refer to PRECAUTION