LEMON Manuals: Even more car manuals for everyone

No. Fast Idle/Runs On: Procedure

  1. INSPECT COOLING SYSTEM FOR MALFUNCTION 
    1. Access the Engine coolant temperature PID using the Techstream.

      Refer to ON-BOARD DIAGNOSTIC TEST

    2. Start the engine and warm it up completely.
    3. Is the Engine coolant temperature PID value between 82-112°C {180-234°F}?

      Result

      Result
      Yes
      No

    Result:  2

    No 

    ENGINE COOLANT TEMPERATURE PID VALUE IS HIGHER THAN 112°C {234°F}: 

    1. Engine coolant temperature PID value is higher than 112°C {234°F}:
      1. Perform the symptom troubleshooting "NO. 17 COOLING SYSTEM CONCERNS-OVERHEATING".

        Refer to NO. 17 COOLING SYSTEM CONCERNS-OVERHEATING 

    2. Engine coolant temperature PID value is less than 82°C {180°F}:
      1. Perform the symptom troubleshooting "NO. 18 COOLING SYSTEM CONCERNS-RUNS COLD".

        Refer to NO. 18 COOLING SYSTEM CONCERNS-RUNS COLD 

    Result:  1

    Yes 

    See step  2

  2. VERIFY ECM DTC 
    1. Retrieve any DTCs using the Techstream.

      Refer to ON-BOARD DIAGNOSTIC TEST

    2. Are any DTCs present?

      Result

      Result
      Yes
      No

    Result:  2

    Yes 

    GO TO THE APPLICABLE DTC INSPECTION. 

    1. Refer to DIAGNOSTIC TROUBLE CODE CHART

    Result:  1

    No 

    See step  3

  3. VERIFY CURRENT INPUT SIGNAL STATUS 
    NOTE:
    • While performing this step, always operate the vehicle in a safe and lawful manner.
    • When the Techstream is used to observe monitor system status while driving, be sure to have another technician with you, or record the data in the Techstream using the PID/DATA MONITOR AND RECORD capturing function and inspect later.
    1. Access the following PIDs using the Techstream:

      Refer to ON-BOARD DIAGNOSTIC TEST

      1. Accelerator pedal position sensor 1
      2. Accelerator pedal position sensor 2
      3. Clutch Pedal Position Switch/Neutral Switch Circuit (MTX)
      4. Heated Exhaust Gas Oxygen Sensor (bank 1, sensor 1)
      5. Heated Exhaust Gas Oxygen Sensor (bank 1, sensor 2)
      6. Short term fuel trim 1
      7. Long term fuel trim 1
    2. Do the PIDs indicate the correct values under the malfunction condition?

      Refer to INSPECTION

      Result

      Result
      Yes
      No

    Result:  2

    No 

    ACCELERATOR PEDAL POSITION SENSOR 1, ACCELERATOR PEDAL POSITION SENSOR 2 PIDS ARE NOT AS SPECIFIED: 

    1. Accelerator pedal position sensor 1, Accelerator pedal position sensor 2 PIDs are not as specified:
      1. Inspect the APP sensor.

        Refer to INSPECTION

    2. Clutch Pedal Position Switch/Neutral Switch Circuit PID is not as specified: (MTX)
      1. Inspect the neutral switch.

        Refer to INSPECTION

    3. Heated Exhaust Gas Oxygen Sensor (bank 1, sensor 1), Short term fuel trim 1, Long term fuel trim 1 PIDs are not as specified:
      1. Inspect the A/F sensor.

        Refer to INSPECTION

    4. Heated Exhaust Gas Oxygen Sensor (bank 1, sensor 2) PID is not as specified:
      1. Inspect the HO2S.

        Refer to INSPECTION

    5. Repair or replace the malfunctioning part according to the inspection results.
      1. If the malfunction remains:
        • Inspect communication error between TCM and ECM. (ATX)
          • Repair or replace the malfunctioning part according to the inspection results if necessary.

    Result:  1

    Yes 

    See step  4

  4. DETERMINE IF MALFUNCTION CAUSE IS A/C REQUEST SIGNAL OR OTHER 
    1. Access the A/C Request Signal PID using the Techstream.

      Refer to ON-BOARD DIAGNOSTIC TEST

    2. Monitor the A/C Request Signal PID while turning on and off the air conditioner using the switch on the control panel.
    3. Does the A/C Request Signal PID value change from Yes(True) to No(False) according to switch control panel?

      Result

      Result
      Yes
      No

    Result:  2

    No 

    IF THE A/C REQUEST SIGNAL PID IS ALWAYS ON: 

    1. If the A/C Request Signal PID is always Yes(True):
      1. Perform the symptom troubleshooting "NO. 24 A/C IS ALWAYS ON OR A/C COMPRESSOR RUNS CONTINUOUSLY".

        Refer to NO. 24 A/C IS ALWAYS ON OR A/C COMPRESSOR RUNS CONTINUOUSLY 

    2. If the A/C Request Signal PID is always No(False):
      1. Perform the symptom troubleshooting "NO. 23 A/C DOES NOT WORK SUFFICIENTLY".

        Refer to NO. 23 A/C DOES NOT WORK SUFFICIENTLY 

    Result:  1

    Yes 

    See step  5

  5. INSPECT DRIVE-BY-WIRE CONTROL SYSTEM OPERATION 
    1. Perform the Electronic Control Throttle Operation Inspection.

      Refer to ON-VEHICLE INSPECTION

    2. Does the drive-by-wire control system work properly?

      Result

      Result
      Yes
      No

    Result:  1

    No 

    REPAIR OR REPLACE THE MALFUNCTIONING PART ACCORDING TO THE INSPECTION RESULTS. 

    Result:  2

    Yes 

    See step  10

  6. INSPECT FUEL INJECTOR OPERATION 
    1. Perform the Fuel Injector Operation Inspection.

      Refer to ON-VEHICLE INSPECTION

    2. Do the fuel injectors operate properly?

      Result

      Result
      Yes
      No

    Result:  2

    No 

    REPAIR OR REPLACE THE MALFUNCTIONING PART ACCORDING TO THE INSPECTION RESULTS. 

    Result:  1

    Yes 

    See step  7

  7. INSPECT HIGH PRESSURE FUEL PUMP 
    1. Inspect the high pressure fuel pump.

      Refer to INSPECTION

    2. Is there any malfunction?

      Result

      Result
      Yes
      No

    Result:  2

    Yes 

    REPLACE THE HIGH PRESSURE FUEL PUMP. 

    1. Refer to REMOVAL

    Result:  1

    No 

    See step  8

  8. INSPECT CRUISE CONTROL SYSTEM 
    1. Inspect the operation of cruise control system.
    2. Does the cruise control system work properly?

      Result

      Result
      Yes
      No

    Result:  2

    No 

    REPAIR OR REPLACE THE MALFUNCTIONING PART ACCORDING TO THE INSPECTION RESULTS. 

    Result:  1

    Yes 

    See step  9

  9. INSPECT INTAKE-AIR SYSTEM FOR AIR LEAKAGE 
    1. Inspect for leakage in intake-air system.
    2. Is there any leakage?

      Result

      Result
      Yes
      No

    Result:  1

    No 

    INJECTOR DRIVER MALFUNCTION. 

    1. Injector driver malfunction.
      1. Replace the ECM.

        Refer to REMOVAL

    2. If the problem remains, overhaul the engine.

    Result:  2

    Yes 

    REPAIR OR REPLACE THE MALFUNCTIONING PART ACCORDING TO THE INSPECTION RESULTS. 

  10. VISUALLY INSPECT THE THROTTLE BODY (DAMAGE/SCRATCHING). 
    1. If there is any malfunction:
      1. Repair or replace the malfunctioning part according to the inspection results.
    2. If there is no malfunction:
      1. Go to the next step.

        Result

        Proceed to
        NEXT

    Result:  1

    NEXT 

    See step  6