LEMON Manuals: Even more car manuals for everyone

Battery / Charging System (Service Information): Battery: Installation: Procedure

  1. ECM CONNECTOR CONNECTION NOTE 
    NOTE:
    • Do not touch the ECM connector terminal. The terminal is extremely thin and can be damaged by touching it.
    • If the ECM connector is inserted at an angle and the lever is moved, the connector could be damaged. Verify that the ECM connector is inserted straight.
      GTY485360Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Yes
      *b No
    1. Set the ECM connector lever to the position shown in the figure.
      GTY494471Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Lever
      *b ECM Connector Front Harness-Side
      *c ECM Connector Emission Harness-Side
    2. Align the ECM connector straight against the connection surface.
      GTY488646Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a ECM
    3. Insert the ECM connector straight and press it in until the lever moves up naturally. (Front harness side connector)
      GTY492414Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Press In
    4. Press the ECM connector lever until a click sound is heard.
      GTY491192Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Click
  2. BATTERY BOX INSTALLATION NOTE 
    1. Install the battery box so that the side with the larger notch is pointed at the engine side.
      GTY492089Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Notch
      *b Engine Side
      *c Vehicle Front
  3. NEGATIVE BATTERY CABLE CONNECTION NOTE (WITH CURRENT SENSOR) 
    1. Connect the negative battery cable with the current sensor and the battery parallel to each other.
      GTY494145Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Current Sensor
  4. INSTALL BATTERY 
    1. Install the battery tray and ECM component.

      Torque: 26 N*m (265 kgf*cm, 19 ft.*lbf) 

      GTY487695Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Negative Battery Cable *2 Positive Battery Cable
      *3 Battery Clamp *4 Battery Box
      *5 Battery *6 Battery Tray Bolt
      *7 ECM Connector *8 Battery Tray and ECM Component
      N*m (kgf*cm, ft.*lbf): Specified torque - -
    2. When replacing the battery tray with a new one, perform the following procedure:
      GTY482924Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 ECM
      *2 Bracket
      *3 Bracket
      *a Screw
      *b Bolt
      *c Nut
      N*m (kgf*cm, ft.*lbf): Specified torque
      1. Install the bracket.

        Torque: 9.0 N*m (92 kgf*cm, 80 in.*lbf) 

      2. Install the bracket.

        Torque: 3.0 N*m (31 kgf*cm, 27 in.*lbf) 

      3. Install the ECM.

        Torque: 9.0 N*m (92 kgf*cm, 80 in.*lbf) 

    3. Install the ECM connector.

      See step  1

    4. Install the battery tray bolt.
    5. Install the battery.
    6. Install the battery box.

      See step  2

    7. Install the battery clamp.

      Torque: 5.95 N*m (61 kgf*cm, 53 in.*lbf) 

    8. Install the positive battery cable.

      Torque: 5.0 N*m (51 kgf*cm, 44 in.*lbf) 

    9. Install the negative battery cable.

      Torque: 5.0 N*m (51 kgf*cm, 44 in.*lbf) 

      See step  3

  5. BATTERY RECHARGING 
    WARNING:
    • Keep all flames away from the battery and perform the servicing in a well-ventilated area. Otherwise, evaporated gas from the battery could ignite.
    • Do not leave the battery in the vehicle when recharging. Otherwise, damage to under-hood components from electrolyte overflow, misting or gassing, may occur.
    • When connecting to the battery recharger, make sure the battery cables are connected correctly.
    1. Using GR8-1291:
      1. Remove the battery.

        Refer to REMOVAL 

      2. Check the water level. If necessary, add water to the appropriate level.
      3. Attach the large red clamp to the positive battery terminal and the large black clamp to the negative terminal.
      4. Select the diagnostic icon in the Main Menu, then press the NEXT key.
      5. Follow the on-screen instructions to input the appropriate information. Refer to the GR8-1291 Instruction Manual for more information.
      6. The GR8-1291 will test and charge the battery. Before the diagnostic charging results are displayed, use the keypad on the Control Module to input the last 5 digits of the vehicle's VIN and press NEXT to continue.
      7. After the charging is completed, the GR8-1291 will print out the diagnostic charging results and display one of the following results listed below. Review the results and follow the action step for the displayed result.
        Battery Tester Display Action Step
        GOOD BATTERY Return the battery to service.
        REPLACE BATTERY Replace the battery.
        BAD CELL - REPLACE Replace the battery.
        WARNING:

        Do not charge the battery. Charging a battery with one or more bad cells could cause an explosion and serious harm to the user.

        SIDE POST TEST Test data was inconclusive using the side post. Retest using side post adapters.
        JUMP START POST Data was inconclusive using the jump start post. Retest at the battery terminals.
    2. Without Using GR8-1291:
      NOTE:

      Do not quick charge for more than 30 minutes. It will damage the battery.

      1. Remove the battery.

        Refer to REMOVAL 

      2. Connect a battery charger to the battery and adjust the charging current as follows.

        Battery slow charge current

        GR35 (60 A*h/20HR): 4.5 to 5.5 A

        Battery quick charge current [30 min]

        GR35 (60 A*h/20HR): 30 A

        GTY485038Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Battery Charger
        *b Negative Cable
        *c Negative Terminal
        *d Positive Cable
        *e Positive Terminal
        *f Battery
      3. After the battery is recharged, verify that the voltage is within the specification and remains at the same value for 1 hour or more after the recharging has been completed.

        If not within specification, replace the battery.

        Standard voltage

        12.4 V or more