LEMON Manuals: Even more car manuals for everyone

Windshield Glass: Removal: Procedure

  1. REMOVE WINDSHIELD GLASS 
    1. Disconnect the negative battery cable.

      Refer to REMOVAL

    2. Remove the following parts:
      1. Windshield wiper arm and blade

        Refer to PROCEDURE - Step 1

      2. Cowl grille

        Refer to PROCEDURE - Step 1

      3. Front fender molding

        Refer to PROCEDURE - Step 1

      4. Side cowl grille

        Refer to PROCEDURE - Step 1

      5. A-pillar trim

        Refer to PROCEDURE - Step 1

      6. Sunvisor

        Refer to PROCEDURE - Step 1

      7. Front map light

        Refer to REMOVAL

      8. Sensor cover (with smart city brake support (SCBS))

        See step  1

      9. Laser sensor (with smart city brake support (SCBS))

        Refer to PROCEDURE - Step 2

      10. Rearview mirror

        Refer to PROCEDURE - Step 1

    3. Set the headliner out of the way.
    4. Apply protective tape along the edge of the body.

      HINT: 

      Overlap and adhere the protective tape to the corners to prevent damage.

      GTY492703Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Corner *b Protective Tape
      *c Windshield - -
    5. Remove the windshield molding by pulling it outward.

      HINT: 

      If the windshield molding is difficult to remove, warm the windshield molding using a hot air blower.

      GTY492104Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Windshield Molding *b Windshield
      *c SEC. A-A • Non-reusable part
    6. Cut the tip of the piano wire diagonally to facilitate insertion of the piano wire through the sealant.
      GTY492323Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Piano Wire
    7. Pass the piano wire through from the cabin side.
      NOTE:

      Carefully pass the piano wire so as not to damage the body. If the piano wire contacts the body, the paint may be damaged.

      GTY492668Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Piano Wire
      *b Sealant
      *c Windshield
    8. Install the piano wire to the piano wire grip.
    9. Secure the piano wire on the outer side, and pull the wire on the cabin side in the direction of the arrow shown in the figure to cut the windshield sealant.

      HINT: 

      Use a long sawing action to spread the work over the whole length of piano wire to prevent it from breaking due to localized heating.

      GTY483472Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Piano Wire Grip
      *b Piano Wire
      *c Windshield
    10. When reaching the pin, pull the piano wire out to go around the pin, then pass the piano wire through from the cabin side again.
      GTY491500Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Pin *b Piano Wire
      *c Headliner - -
    11. Secure one end of piano wire, and while pulling the other end, cut the sealant around the windshield.
    12. Pinch the pin from the inside of the vehicle and detach it.

      HINT: 

      Before removing the windshield from the body, mark the windshield by affixing tape to the windshield and body panel.

    13. Remove the windshield.
    14. If the pin is damaged, remove the pin.

      HINT: 

      Before removing the pin from the windshield glass, place an alignment mark on the windshield.

  2. REMOVE NOT REUSING WINDSHIELD 
    1. Disconnect the negative battery cable.

      Refer to PROCEDURE - Step 1

    2. Remove the following parts:
      1. Windshield wiper arm and blade

        Refer to PROCEDURE - Step 1

      2. Cowl grille

        Refer to PROCEDURE - Step 1

      3. Front fender molding

        Refer to PROCEDURE - Step 1

      4. Side cowl grille

        Refer to PROCEDURE - Step 1

      5. A-pillar trim

        Refer to PROCEDURE - Step 1

      6. Sunvisor

        Refer to PROCEDURE - Step 1

      7. Front map light (dual light type)

        Refer to PROCEDURE - Step 1

      8. Assist handle

        Refer to PROCEDURE - Step 1

      9. Sensor cover (with smart city brake support (SCBS))

        See step  1

      10. Laser sensor (with smart city brake support (SCBS))

        Refer to PROCEDURE - Step 2

      11. Rearview mirror

        Refer to PROCEDURE - Step 1

    3. Set the headliner out of the way.
    4. Apply protective tape along the edge of the body.

      HINT: 

      Overlap and adhere the protective tape to the corners to prevent damage.

      GTY492703Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Corner *b Protective Tape
      *c Windshield - -
    5. Remove the windshield molding by pulling it outward.

      HINT: 

      If the windshield molding is difficult to remove, warm the windshield molding using a hot air blower.

      GTY491765Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Windshield Molding *b Windshield
      *c SEC. A-A • Non-reusable part
    6. Cut out the sealant all around the glass using a sealant remover.
      GTY488184Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Windshield *b Sealant Remover

      HINT: 

      If it is difficult to cut sealant, use piano wire and follow the procedure under "Reusing Windshield".

    7. Remove the windshield.