LEMON Manuals: Even more car manuals for everyone

Installation [11/2015 - ]: Procedure

  1. INSTALL BREATHER TUBE CLAMP 
    1. Engage the claw and clamp and install the breather tube clamp.
  2. INSTALL FUEL TANK FILLER PIPE PROTECTOR 
    1. Engage the 2 claws and install the fuel tank filler pipe protector.
    2. Engage the 2 claws and install the No. 1 fuel tube support protector.
    3. Install the clip to the fuel tank filler pipe protector.
  3. INSTALL FUEL TANK VENT HOSE SUB-ASSEMBLY 
    1. Install the fuel tank vent hose sub-assembly onto the fuel tank assembly.
  4. INSTALL FUEL TANK MAIN TUBE SUB-ASSEMBLY 
    1. Install the fuel tank main tube onto the fuel tank assembly.
  5. INSTALL FUEL TANK ASSEMBLY 
    1. Clean and degrease the bolt holes.
    2. Using an engine lifter, set the fuel tank assembly in the installation position.
      NOTE:

      Do not drop the fuel tank.

    3. Install the fuel tank assembly with 4 new bolts.

      Torque: 14 N*m (146 kgf*cm, 11 ft.*lbf) 

    4. Engage the claw and install the fuel tank filler pipe.
    5. Install the bolt.

      Torque: 34 N*m (347 kgf*cm, 25 ft.*lbf) 

  6. INSTALL CHARCOAL CANISTER ASSEMBLY 

    Refer to PROCEDURE - Step 6

  7. CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY 
    1. Align the fuel tube connector with the fuel pipe, connect the fuel tube connector and push the retainer in until the retainer makes a "click" sound to lock the claws of the retainer.
      GTY735625Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002.
      GTY728283Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002.
      TEXT IN ILLUSTRATION

      *1 Fuel Tank Main Tube Sub-assembly
      *2 Fuel Tank Pipe Setting Holder
      *3 Retainer
      *4 Nylon Tube
      *5 O-ring
      *6 Fuel Tube Connector
      *7 Fuel Pipe
      NOTE:
      • Check that there is no damage or foreign matter around the connecting parts of the fuel tube connector and fuel pipe before starting this step.
      • After connecting the fuel tube connector, check that the fuel tube connector is securely connected by pulling on the fuel tube connector.
    2. Engage the clamp and install the fuel tank pipe setting holder.
  8. INSTALL NO. 1 FUEL TUBE PROTECTOR 
    1. Install the No. 1 fuel tube protector to the fuel tube connector.
  9. INSTALL NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY 
    1. Install the No. 1 fuel tank protector sub-assembly with the bolt and clip.

      Torque: 5.4 N*m (55 kgf*cm, 48 in.*lbf) 

  10. INSTALL FRONT NO. 4 FLOOR HEAT INSULATOR 
    1. Install the front No. 4 floor heat insulator with the 2 nuts.
      GTY701042Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002.
      TEXT IN ILLUSTRATION

      *a Front

      Nut A 

      Torque: 5.5 N*m (56 kgf*cm, 49 in.*lbf) 

      Nut B 

      Torque: 5.4 N*m (55 kgf*cm, 48 in.*lbf) 

  11. INSTALL FUEL TANK CAP ASSEMBLY 
  12. INSTALL FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY 

    (Refer to INSTALLATION [11/2015 - 12/2016] , or refer to INSTALLATION [12/2016 - ] )

  13. ADD FUEL 
  14. INSTALL REAR WHEEL (for LH Side) 

    Torque: 103 N*m (1050 kgf*cm, 76 ft.*lbf)