LEMON Manuals: Even more car manuals for everyone

BRAKE ACTUATOR (w/o VSC): Installation: Installation

  1. INSTALL BRAKE ACTUATOR 
    1. Install the brake actuator to the brake actuator bracket assembly with the 3 bolts.
      Fig 1: Locating Brake Actuator Assembly Bolts
      GTY183775Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Torque: 5.4 N*m (55 kgf*cm, 48 in.*lbf) 

      NOTE:
      • Do not remove the hole plugs of a new brake actuator before connecting the 6 brake lines because the brake actuator is filled with brake fluid.
      • Do not carry the brake actuator assembly by the connector.
      • Tighten the 3 bolts in the order shown in the illustration.
  2. INSTALL BRAKE ACTUATOR WITH BRACKET 
    1. Install the brake actuator with bracket to the body with the 2 bolts and nut.
      Fig 2: Locating Brake Actuator Bolts And Nut
      GTY204731Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Torque: 19 N*m (194 kgf*cm, 14 ft.*lbf) 

      NOTE:
      • Do not damage the brake lines or wire harness.
      • Tighten the nut and 2 bolts in the order shown in the illustration.
    2. Temporarily tighten each brake line to the correct position of the brake actuator assembly with bracket as shown in the illustration.

      HINT: 

      • *1: To front wheel cylinder RH
      • *2: To front wheel cylinder LH
      • *3: To rear wheel cylinder RH
      • *4: To rear wheel cylinder LH
      • *5: From 1st master cylinder
      • *6: From 2nd master cylinder
      Fig 3: Identifying Brake Lines
      GTY223326Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Using a union nut wrench (10 mm), fully tighten each brake line.
      Fig 4: View Of Brake Line Tightening Procedure
      GTY177949Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      without a union nut wrench 

      Torque: 15 N*m (155 kgf*cm, 11 ft.*lbf) 

      with a union nut wrench 

      Torque: 14 N*m (143 kgf*cm, 10 ft.*lbf) 

      NOTE:
      • Use a torque wrench with a fulcrum length of 250 mm (9.84 in.).
      • This torque value is effective when the union nut wrench is parallel to the torque wrench.
    4. Install the brake line clamp with brake line with the bolt.

      Torque: 5.4 N*m (55 kgf*cm, 48 in.*lbf) 

      Fig 5: Locating Brake Line Clamp And Bolt
      GTY204728Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Connect the actuator connector and lock the lock lever.
      Fig 6: Locating Actuator Connector
      GTY244535Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      NOTE:

      Make sure that the connector is locked securely.

  3. INSTALL RADIATOR RESERVE TANK ASSEMBLY 
    1. Install the radiator reserve tank assembly with the 3 bolts.

      Torque: 7.0 N*m (71 kgf*cm, 62 in.*lbf) 

      Fig 7: Locating Radiator Reserve Tank Assembly Mounting Bolts
      GTY232433Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  4. INSTALL WINDSHIELD WASHER JAR ASSEMBLY 
    1. Install the windshield washer jar assembly and clamp to the body with the 2 bolts.

      Torque: 5.5 N*m (56 kgf*cm, 49 in.*lbf) 

      Fig 8: Locating Windshield Washer Jar Assembly, Bolt And Clamp
      GTY204980Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Install the bolt and clamp connect the washer hoses and motor connectors.

      Torque: 5.5 N*m (56 kgf*cm, 49 in.*lbf) 

      Fig 9: Locating Washer Hoses, Motor Connectors, Bolt And Clamp
      GTY218759Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  5. INSTALL FRONT BUMPER ASSEMBLY 

    HINT: 

    Refer to the instructions for Installation of the front bumper assembly . Refer to INSTALLATION .

  6. INSTALL GENERATOR ASSEMBLY (for 2ZR-FE) 

    HINT: 

    Refer to the instructions for Installation of the generator assembly . Refer to INSTALLATION - Step 1 .

  7. INSTALL GENERATOR ASSEMBLY (for 2AZ-FE) 

    HINT: 

    Refer to the instructions for Installation of the generator assembly . Refer to INSTALLATION - Step 1 .

  8. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL 
  9. REMOVE CENTER COWL TOP VENTILATOR LOUVER  . Refer to REPLACEMENT - Step 1
  10. FILL UP BRAKE FLUID RESERVOIR  . Refer to REPLACEMENT - Step 2
  11. BLEED BRAKE MASTER CYLINDER  . Refer to BLEEDING - Step 3
  12. BLEED BRAKE LINE  . Refer to REPLACEMENT - Step 3
  13. INSPECT BRAKE FLUID LEVEL  . Refer to ON-VEHICLE INSPECTION - Step 1
  14. INSPECT FOR FLUID LEAK 
  15. INSTALL CENTER COWL TOP VENTILATOR LOUVER  . Refer to REPLACEMENT - Step 6
  16. INSPECT ACTUATOR USING TECHSTREAM 

    HINT: 

    Refer to ON-VEHICLE INSPECTION 

  17. PREPARATION FOR FOG LIGHT AIMING (w/ Fog Light)  . Refer to ADJUSTMENT - Step 2
  18. INSPECT FOG LIGHT AIMING (w/ Fog Light)  . Refer to ADJUSTMENT - Step 3
  19. ADJUST FOG LIGHT AIMING (w/ Fog Light)  . Refer to ADJUSTMENT - Step 4